IPAC2014 - List of Authors (Steele, G.E.)

Paper	Title	Page
MOPRO021	Power Deposition in LHC Magnets With and Without Dispersion Suppressor Collimators Downstream of the Betatron Cleaning Insertion	112
	A. Lechner, B. Auchmann, R. Bruce, F. Cerutti, P.P. Granieri, A. Marsili, S. Redaelli, N.V. Shetty, E. Skordis, G.E. Steele, A.P. Verweij CERN, Geneva, Switzerland
	The power deposited in dispersion suppressor (DS) magnets downstream of the LHC betatron cleaning insertion is governed by off-momentum protons which predominantly originate from single-diffractive interactions in primary collimators. With higher beam energy and intensities anticipated in future operation, these clustered proton losses could possibly induce magnet quenches during periods of short beam lifetime. In this paper, we present FLUKA simulations for nominal 7 TeV operation, comparing the existing layout with alternative layouts where selected DS dipoles are substituted by pairs of shorter higher-field magnets and a collimator. Power densities predicted for different collimator settings are compared against present estimates of quench limits. Further, the expected reduction factor due to DS collimators is evaluated.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRO032	Upgrades to the LHC Injection and Beam Dumping Systems for the HL-LHC Project	141
	J.A. Uythoven, M.J. Barnes, B. Goddard, J. Hrivnak, A. Lechner, F.L. Maciariello, A. Mereghetti, A. Perillo Marcone, N.V. Shetty, G.E. Steele CERN, Geneva, Switzerland
	The HL-LHC project will push the performance of the LHC injection and beam dumping systems towards new limits. This paper describes the systems affected and presents the new beam parameters for these systems. It also describes the studies to be performed to determine which sub-components of these systems need to be upgraded to fulfill the new HL-LHC requirements. The results from the preliminary upgrade studies for the injection absorbers TDI are presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO032
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI096	The New Transfer Line Collimation System for the LHC High Luminosity Era	839
	V. Kain, C. Bracco, B. Goddard, F.L. Maciariello, M. Meddahi, A. Mereghetti, G.E. Steele, F.M. Velotti CERN, Geneva, Switzerland E. Gianfelice-Wendt Fermilab, Batavia, Illinois, USA
	A set of passive absorbers is located at the end of each of the 3 km long injection lines to protect the LHC in case of failures during the extraction process from the LHC’s last pre-injector or the beam transfer itself. In case of an erroneous extraction, the absorbers have to attenuate the beam to a safe level and be robust enough themselves to survive the impact. These requirements are difficult to fulfil with the very bright and intense beams produced by the LHC injectors for the high luminosity era. This paper revisits the requirements for the SPS-to-LHC transfer line collimation system and the adapted strategy to fulfill these for the LHC high luminosity operation. A possible solution for the new transfer line collimation system is presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI096
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI098	Design Studies of the Upgraded Collimation System in the SPS-to-LHC Transfer Lines	845
	A. Mereghetti, C. Bracco, F. Cerutti, B. Goddard, J. Hrivnak, V. Kain, F.L. Maciariello, M. Meddahi, G.E. Steele CERN, Geneva, Switzerland R. Appleby UMAN, Manchester, United Kingdom
	In the framework of the LHC Injectors Upgrade (LIU) Project, the collimators in the SPS-to-LHC transfer lines are presently under re-design, in order to cope with the unprecedented beam intensities and emittances required by the High Luminosity LHC (HL-LHC). Factors ruling the design phase are the robustness of the jaws on one side and, on the other side, the proton absorption and the emittance blow-up, essential for an effective protection of the equipment in the LHC injection regions and the LHC machine. In view of the new design, based on the one of the currently installed TCDI collimators and past investigations, the FLUKA Monte Carlo code is used to address these two factors. The present studies are intended to give essential feedback to the identification of viable solutions.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI098
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME069	Performance Studies of the SPS Beam Dump System for HL-LHC Beams	3394
	F.M. Velotti, O. Aberle, C. Bracco, E. Carlier, F. Cerutti, K. Cornelis, L. Ducimetière, B. Goddard, V. Kain, R. Losito, C. Maglioni, M. Meddahi, F. Pasdeloup, V. Senaj, G.E. Steele CERN, Geneva, Switzerland
	The Super Proton Synchrotron (SPS) beam dump system is a concern for the planned High Luminosity LHC (HL-LHC) operation. The system has initially been designed for very different beam parameters compared to those which will reign after the completion of the LHC injectors upgrade, when the SPS will have to operate with unprecedented beam brightness. This paper describes the relevant operational and failure modes of the dump system together with the expected beam loading levels. Tracking studies are presented, considering both normal operation and failure scenarios, with particular attention on the location and level of proton losses. First FLUKA investigations and thermo-mechanical analysis of the high-energy absorber block are described
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME069
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Power Deposition in LHC Magnets With and Without Dispersion Suppressor Collimators Downstream of the Betatron Cleaning Insertion

112

A. Lechner, B. Auchmann, R. Bruce, F. Cerutti, P.P. Granieri, A. Marsili, S. Redaelli, N.V. Shetty, E. Skordis, G.E. Steele, A.P. Verweij
CERN, Geneva, Switzerland

The power deposited in dispersion suppressor (DS) magnets downstream of the LHC betatron cleaning insertion is governed by off-momentum protons which predominantly originate from single-diffractive interactions in primary collimators. With higher beam energy and intensities anticipated in future operation, these clustered proton losses could possibly induce magnet quenches during periods of short beam lifetime. In this paper, we present FLUKA simulations for nominal 7 TeV operation, comparing the existing layout with alternative layouts where selected DS dipoles are substituted by pairs of shorter higher-field magnets and a collimator. Power densities predicted for different collimator settings are compared against present estimates of quench limits. Further, the expected reduction factor due to DS collimators is evaluated.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRO032

Upgrades to the LHC Injection and Beam Dumping Systems for the HL-LHC Project

141

J.A. Uythoven, M.J. Barnes, B. Goddard, J. Hrivnak, A. Lechner, F.L. Maciariello, A. Mereghetti, A. Perillo Marcone, N.V. Shetty, G.E. Steele
CERN, Geneva, Switzerland

The HL-LHC project will push the performance of the LHC injection and beam dumping systems towards new limits. This paper describes the systems affected and presents the new beam parameters for these systems. It also describes the studies to be performed to determine which sub-components of these systems need to be upgraded to fulfill the new HL-LHC requirements. The results from the preliminary upgrade studies for the injection absorbers TDI are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO032

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI096

The New Transfer Line Collimation System for the LHC High Luminosity Era

839

V. Kain, C. Bracco, B. Goddard, F.L. Maciariello, M. Meddahi, A. Mereghetti, G.E. Steele, F.M. Velotti
CERN, Geneva, Switzerland
E. Gianfelice-Wendt
Fermilab, Batavia, Illinois, USA

A set of passive absorbers is located at the end of each of the 3 km long injection lines to protect the LHC in case of failures during the extraction process from the LHC’s last pre-injector or the beam transfer itself. In case of an erroneous extraction, the absorbers have to attenuate the beam to a safe level and be robust enough themselves to survive the impact. These requirements are difficult to fulfil with the very bright and intense beams produced by the LHC injectors for the high luminosity era. This paper revisits the requirements for the SPS-to-LHC transfer line collimation system and the adapted strategy to fulfill these for the LHC high luminosity operation. A possible solution for the new transfer line collimation system is presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI096

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI098

Design Studies of the Upgraded Collimation System in the SPS-to-LHC Transfer Lines

845

A. Mereghetti, C. Bracco, F. Cerutti, B. Goddard, J. Hrivnak, V. Kain, F.L. Maciariello, M. Meddahi, G.E. Steele
CERN, Geneva, Switzerland
R. Appleby
UMAN, Manchester, United Kingdom

In the framework of the LHC Injectors Upgrade (LIU) Project, the collimators in the SPS-to-LHC transfer lines are presently under re-design, in order to cope with the unprecedented beam intensities and emittances required by the High Luminosity LHC (HL-LHC). Factors ruling the design phase are the robustness of the jaws on one side and, on the other side, the proton absorption and the emittance blow-up, essential for an effective protection of the equipment in the LHC injection regions and the LHC machine. In view of the new design, based on the one of the currently installed TCDI collimators and past investigations, the FLUKA Monte Carlo code is used to address these two factors. The present studies are intended to give essential feedback to the identification of viable solutions.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI098

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPME069

Performance Studies of the SPS Beam Dump System for HL-LHC Beams

3394

F.M. Velotti, O. Aberle, C. Bracco, E. Carlier, F. Cerutti, K. Cornelis, L. Ducimetière, B. Goddard, V. Kain, R. Losito, C. Maglioni, M. Meddahi, F. Pasdeloup, V. Senaj, G.E. Steele
CERN, Geneva, Switzerland

The Super Proton Synchrotron (SPS) beam dump system is a concern for the planned High Luminosity LHC (HL-LHC) operation. The system has initially been designed for very different beam parameters compared to those which will reign after the completion of the LHC injectors upgrade, when the SPS will have to operate with unprecedented beam brightness. This paper describes the relevant operational and failure modes of the dump system together with the expected beam loading levels. Tracking studies are presented, considering both normal operation and failure scenarios, with particular attention on the location and level of proton losses. First FLUKA investigations and thermo-mechanical analysis of the high-energy absorber block are described

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME069

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)