IPAC2014 - List of Authors (Mikawa, K.)

Paper	Title	Page
MOPRO001	Upgrade Status of Injector LINAC for SuperKEKB	59
	T. Miura, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, Y. Funakoshi, K. Furukawa, T. Higo, H. Honma, R. Ichimiya, N. Iida, M. Ikeda, E. Kadokura, H. Kaji, K. Kakihara, T. Kamitani, H. Katagiri, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, F. Miyahara, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, Y. Ohnishi, S. Ohsawa, F. Qiu, M. Satoh, T. Shidara, A. Shirakawa, H. Sugimoto, T. Suwada, T. Takenaka, M. Tanaka, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou KEK, Ibaraki, Japan D. Satoh TIT, Tokyo, Japan
	The SuperKEKB collider is under construction to achieve 40-times higher luminosity than that of previous KEKB collider. The injector LINAC should provide high-intensity and low-emittance beams of 7-GeV electron and 4-GeV positron for SuperKEKB based on a nano-beam scheme. A photocathode RF-gun for low emittance electron beam has been already installed and the commissioning has started. The construction of positron capture section using a flux-concentrator and the dumping ring for low emittance positron beam is in progress. The simultaneous top-up injections to four storage-rings including photon factories is also required. In the upstream of dumping ring, the compatible optics between positron and electron has been designed. In the downstream of dumping ring, RF phase, focusing, and steering magnets will be switched by pulse to pulse against each beam-mode for optimising beam-transportation. This paper describes recent upgrade status toward the SuperKEKB.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO001
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI002	Design, Manufacture and Operation of the Beam Spoiler for Positron Target Protection	573
	L. Zang, K. Kakihara, T. Kamitani, K. Mikawa, F. Miyahara, T. Suwada KEK, Ibaraki, Japan
	In order to produce positrons, intensive pulsed electron beam is used to strike on a tungsten target. The energy deposition is distributed non-uniformly over the target, leading to a mechanical stress. As a result of large thermal gradient, the target could be potentially damaged. To avoid the target destruction, the peak energy deposition density (PEDD) in the target should be well below the critical limit (35J/g) based on the SLAC operational experience. With an expected primary electron spot size on the target of the SuperKEKB positron source, the PEDD will exceeds the limit. We will introduce a beam spoiler to enlarge the spot size by multiple scattering in thin beam screen and aluminum plate. It reduces the PEDD down to half of the limit. This paper describes the design of the spoiler and the beam screen system used in the positron beam commissioning of the SuperKEKB positron source started in 2014.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI002
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI004	SuperKEKB Positron Source Construction Status	579
	T. Kamitani, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, Y. Funakoshi, K. Furukawa, T. Higo, H. Honma, N. Iida, M. Ikeda, E. Kadokura, H. Kaji, K. Kakihara, H. Katagiri, M. Kikuchi, H. Koiso, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, T. Mimashi, T. Miura, F. Miyahara, T. Mori, A. Morita, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, Y. Ohnishi, S. Ohsawa, M. Sato, T. Shidara, A. Shirakawa, M. Suetake, H. Sugimoto, T. Suwada, T. Takatomi, T. Takenaka, M. Tanaka, M. Tawada, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou KEK, Ibaraki, Japan D. Satoh TIT, Tokyo, Japan
	The KEKB positron source is under the upgrade for SuperKEKB. The previous positron production target and capture section have been removed and the new system is constructed at a location forty meters upstream to have sufficient energy margin for beam injection to the newly introduced damping ring. A flux concentrator is introduced in the new capture section to make an adiabatic matching system. Large aperture (30mm in diameter) S-band accelerating structures are introduced in the capture section and in the subsequent accelerator module to enlarge the transverse phase space acceptance. The beam focusing system of quadrupoles is also upgraded for a comparable beam acceptance to that of the capture section. This paper reports on the status of the SuperKEKB positron source construction and the preliminary positron beam commissioning.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI004
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Upgrade Status of Injector LINAC for SuperKEKB

59

T. Miura, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, Y. Funakoshi, K. Furukawa, T. Higo, H. Honma, R. Ichimiya, N. Iida, M. Ikeda, E. Kadokura, H. Kaji, K. Kakihara, T. Kamitani, H. Katagiri, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, F. Miyahara, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, Y. Ohnishi, S. Ohsawa, F. Qiu, M. Satoh, T. Shidara, A. Shirakawa, H. Sugimoto, T. Suwada, T. Takenaka, M. Tanaka, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou
KEK, Ibaraki, Japan
D. Satoh
TIT, Tokyo, Japan

The SuperKEKB collider is under construction to achieve 40-times higher luminosity than that of previous KEKB collider. The injector LINAC should provide high-intensity and low-emittance beams of 7-GeV electron and 4-GeV positron for SuperKEKB based on a nano-beam scheme. A photocathode RF-gun for low emittance electron beam has been already installed and the commissioning has started. The construction of positron capture section using a flux-concentrator and the dumping ring for low emittance positron beam is in progress. The simultaneous top-up injections to four storage-rings including photon factories is also required. In the upstream of dumping ring, the compatible optics between positron and electron has been designed. In the downstream of dumping ring, RF phase, focusing, and steering magnets will be switched by pulse to pulse against each beam-mode for optimising beam-transportation. This paper describes recent upgrade status toward the SuperKEKB.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO001

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI002

Design, Manufacture and Operation of the Beam Spoiler for Positron Target Protection

573

L. Zang, K. Kakihara, T. Kamitani, K. Mikawa, F. Miyahara, T. Suwada
KEK, Ibaraki, Japan

In order to produce positrons, intensive pulsed electron beam is used to strike on a tungsten target. The energy deposition is distributed non-uniformly over the target, leading to a mechanical stress. As a result of large thermal gradient, the target could be potentially damaged. To avoid the target destruction, the peak energy deposition density (PEDD) in the target should be well below the critical limit (35J/g) based on the SLAC operational experience. With an expected primary electron spot size on the target of the SuperKEKB positron source, the PEDD will exceeds the limit. We will introduce a beam spoiler to enlarge the spot size by multiple scattering in thin beam screen and aluminum plate. It reduces the PEDD down to half of the limit. This paper describes the design of the spoiler and the beam screen system used in the positron beam commissioning of the SuperKEKB positron source started in 2014.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI002

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPRI004

SuperKEKB Positron Source Construction Status

579

T. Kamitani, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, Y. Funakoshi, K. Furukawa, T. Higo, H. Honma, N. Iida, M. Ikeda, E. Kadokura, H. Kaji, K. Kakihara, H. Katagiri, M. Kikuchi, H. Koiso, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, T. Mimashi, T. Miura, F. Miyahara, T. Mori, A. Morita, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, Y. Ohnishi, S. Ohsawa, M. Sato, T. Shidara, A. Shirakawa, M. Suetake, H. Sugimoto, T. Suwada, T. Takatomi, T. Takenaka, M. Tanaka, M. Tawada, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou
KEK, Ibaraki, Japan
D. Satoh
TIT, Tokyo, Japan

The KEKB positron source is under the upgrade for SuperKEKB. The previous positron production target and capture section have been removed and the new system is constructed at a location forty meters upstream to have sufficient energy margin for beam injection to the newly introduced damping ring. A flux concentrator is introduced in the new capture section to make an adiabatic matching system. Large aperture (30mm in diameter) S-band accelerating structures are introduced in the capture section and in the subsequent accelerator module to enlarge the transverse phase space acceptance. The beam focusing system of quadrupoles is also upgraded for a comparable beam acceptance to that of the capture section. This paper reports on the status of the SuperKEKB positron source construction and the preliminary positron beam commissioning.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRI004

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)