IPAC2013 - List of Authors (Yamamoto, K.)

Paper	Title	Page
MOPME021	Ionization Profile Monitor (IPM) of J-PARC 3-GeV RCS	515
	H. Harada, K. Yamamoto JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan S. Kato Tohoku University, Graduate School of Science, Sendai, Japan
	Ionization profile monitors (IPM) were installed in the 3-GeV RCS ring of J-PARC and used to observe the beam-profile for the transverse plane in beam commissioning. These electrodes and MCPs of IPMs were upgraded in 2012 summer shutdown in order to improve the external electric field for leading the electrons and ions to MCPs. This presentation will be described the results of observed beam profile in beam commissioning and be discussed the new issues for the ion and electron collection mode.

MOPME028	A Preliminary Study of the Vibration Wire Monitor for Beam Halo Diagnostic in J-PARC L3BT	535
	K. Okabe, M. Kinsho, K. Yamamoto, M. Yoshimoto JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
	In the J-PARC 3-GeV Rapid Cycle Synchrotron (RCS), transverse beam halo diagnostic and scraping are required to increase the output beam power. Wire scanners and halo scrapers were used for measurement of projected beam distributions to determine the extent of beam halo formation at Linac-3GeV Beam Transport line (L3BT). In order to determine more detail of halo formation, Vibration Wire Monitor (VWM) was installed in L3BT for the beam halo measurement and the offline study at the test stand with low energy electron gun are started. The high sensitivity of the VWM makes it a prospective one for investigation of beam halo and weak beam scanning. In this paper, we will report a preliminary results of offline studies and beam halo measurement by VWM at L3BT.

THPWO032	Progress of Injection Energy Upgrade Project for J-PARC RCS	3833
	N. Hayashi, H. Harada, K. Horino, H. Hotchi, J. Kamiya, M. Kinsho, P.K. Saha, Y. Shobuda, T. Takayanagi, N. Tani, T. Togashi, T. Ueno, M. Watanabe, Y. Watanabe, K. Yamamoto, M. Yamamoto, Y. Yamazaki, M. Yoshimoto JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan Y. Irie KEK, Ibaraki, Japan T. Toyama J-PARC, KEK & JAEA, Ibaraki-ken, Japan
	The injection energy of the J-PARC RCS will be upgraded in 2013. New power supplies for the shift bump magnet system will be installed. Some of other systems, upgrade of the painting bump power supplies and pulse steering systems, are already installed and tested or used for the nominal operation. The paper reports the progress of injection energy upgrade project.

THPWO033	High Intensity Beam Trial of up to 540 kW in J-PARC RCS	3836
	H. Hotchi, H. Harada, N. Hayashi, M. Kinsho, P.K. Saha, Y. Shobuda, F. Tamura, K. Yamamoto, M. Yamamoto, M. Yoshimoto JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan Y. Irie KEK, Ibaraki, Japan S. Kato Tohoku University, Graduate School of Science, Sendai, Japan
	Recently we have performed a high intensity beam trial of up to 540 kW. In this paper, beam intensity dependece and injection painting parameter dependence of beam loss, observed in this beam experiment, will be discussed with the corresponding numerical simulation results.

Paper

Title

Page

Ionization Profile Monitor (IPM) of J-PARC 3-GeV RCS

515

H. Harada, K. Yamamoto
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
S. Kato
Tohoku University, Graduate School of Science, Sendai, Japan

Ionization profile monitors (IPM) were installed in the 3-GeV RCS ring of J-PARC and used to observe the beam-profile for the transverse plane in beam commissioning. These electrodes and MCPs of IPMs were upgraded in 2012 summer shutdown in order to improve the external electric field for leading the electrons and ions to MCPs. This presentation will be described the results of observed beam profile in beam commissioning and be discussed the new issues for the ion and electron collection mode.

MOPME028

A Preliminary Study of the Vibration Wire Monitor for Beam Halo Diagnostic in J-PARC L3BT

535

K. Okabe, M. Kinsho, K. Yamamoto, M. Yoshimoto
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan

In the J-PARC 3-GeV Rapid Cycle Synchrotron (RCS), transverse beam halo diagnostic and scraping are required to increase the output beam power. Wire scanners and halo scrapers were used for measurement of projected beam distributions to determine the extent of beam halo formation at Linac-3GeV Beam Transport line (L3BT). In order to determine more detail of halo formation, Vibration Wire Monitor (VWM) was installed in L3BT for the beam halo measurement and the offline study at the test stand with low energy electron gun are started. The high sensitivity of the VWM makes it a prospective one for investigation of beam halo and weak beam scanning. In this paper, we will report a preliminary results of offline studies and beam halo measurement by VWM at L3BT.

THPWO032

Progress of Injection Energy Upgrade Project for J-PARC RCS

3833

N. Hayashi, H. Harada, K. Horino, H. Hotchi, J. Kamiya, M. Kinsho, P.K. Saha, Y. Shobuda, T. Takayanagi, N. Tani, T. Togashi, T. Ueno, M. Watanabe, Y. Watanabe, K. Yamamoto, M. Yamamoto, Y. Yamazaki, M. Yoshimoto
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
Y. Irie
KEK, Ibaraki, Japan
T. Toyama
J-PARC, KEK & JAEA, Ibaraki-ken, Japan

The injection energy of the J-PARC RCS will be upgraded in 2013. New power supplies for the shift bump magnet system will be installed. Some of other systems, upgrade of the painting bump power supplies and pulse steering systems, are already installed and tested or used for the nominal operation. The paper reports the progress of injection energy upgrade project.

THPWO033

High Intensity Beam Trial of up to 540 kW in J-PARC RCS

3836

H. Hotchi, H. Harada, N. Hayashi, M. Kinsho, P.K. Saha, Y. Shobuda, F. Tamura, K. Yamamoto, M. Yamamoto, M. Yoshimoto
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
Y. Irie
KEK, Ibaraki, Japan
S. Kato
Tohoku University, Graduate School of Science, Sendai, Japan

Recently we have performed a high intensity beam trial of up to 540 kW. In this paper, beam intensity dependece and injection painting parameter dependence of beam loss, observed in this beam experiment, will be discussed with the corresponding numerical simulation results.