IPAC2012 - List of Authors (Witte, H.)

Paper	Title	Page
MOPPC049	Status of the Non-scaling Fixed Field Alternating Gradient Ring Design for the International Design Study of the Neutrino Factory	241
	J.S. Berg, H. Witte BNL, Upton, Long Island, New York, USA M. Aslaninejad, J. Pasternak Imperial College of Science and Technology, Department of Physics, London, United Kingdom N. Bliss, A.J. Moss STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom D.J. Kelliher, S. Machida STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom S.M. Pattalwar STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
	Funding: This manuscript has been authored by employees of Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy. The International Design Study of the Neutrino Factory is working towards delivering the optimized design of the neutrino factory facility to be presented in the Reference Design Report (RDR) in 2013. In the current baseline design a linear non-scaling fixed field alternating gradient accelerator (FFAG) was chosen as an efficient solution for the final muon acceleration. We describe updates to the design since our previous report. We report on beam dynamics studies on the lattice. We describe recent work on the engineering for the lattice, and the results of a recent first pass at a cost estimate for the machine. Finally, we describe how an FFAG may be applicable to a lower energy neutrino factory in light of recent experimental results regarding the value of the theta(13) neutrino mixing angle. J. S. Berg et al., in Proceedings of IPAC2011, San Sebastian, Spain, 832. ** F. P. An et al., Phys. Rev. Lett. 10⁸, 171803 (2012); J. K. Ahn et al., arXiv:1204.0626v2 [hep-ex] (2012).

MOEPPB003	Status of the PRISM FFAG Design for the Next Generation Muon-to-Electron Conversion Experiment	79
	J. Pasternak, A. Alekou, M. Aslaninejad, R. Chudzinski, L.J. Jenner, A. Kurup, Y. Shi, Y. Uchida Imperial College of Science and Technology, Department of Physics, London, United Kingdom R. Appleby, H.L. Owen UMAN, Manchester, United Kingdom R.J. Barlow University of Huddersfield, Huddersfield, United Kingdom K.M. Hock, B.D. Muratori Cockcroft Institute, Warrington, Cheshire, United Kingdom D.J. Kelliher, S. Machida, C.R. Prior STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom Y. Kuno, A. Sato Osaka University, Osaka, Japan J.-B. Lagrange, Y. Mori Kyoto University, Research Reactor Institute, Osaka, Japan M. Lancaster UCL, London, United Kingdom C. Ohmori KEK, Tokai, Ibaraki, Japan T. Planche TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada S.L. Smith STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom H. Witte BNL, Upton, Long Island, New York, USA T. Yokoi JAI, Oxford, United Kingdom
	The PRISM Task Force continues to study high intensity and high quality muon beams needed for next generation lepton flavor violation experiments. In the PRISM case such beams have been proposed to be produced by sending a short proton pulse to a pion production target, capturing the pions and performing RF phase rotation on the resulting muon beam in an FFAG ring. This paper summarizes the current status of the PRISM design obtained by the Task Force. In particular various designs for the PRISM FFAG ring are discussed and their performance compared to the baseline one, the injection/extraction systems and matching to the solenoid channels upstream and downstream of the FFAG ring are presented. The feasibility of the construction of the PRISM system is discussed.

THPPD020	Test of a 1.8 Tesla, 400 Hz Dipole for a Muon Synchrotron	3542
	D.J. Summers, L.M. Cremaldi, T.L. Hart, L.P. Perera, M. Reep UMiss, University, Mississippi, USA S.U. Hansen, M.L. Lopes Fermilab, Batavia, USA J. Reidy Oxford High School, Mississippi, USA H. Witte BNL, Upton, Long Island, New York, USA
	Funding: Supported by DE-FG05-91ER40622. A 1.8 Tesla dipole magnet using 0.011" AK Steel TRAN-COR H-1 grain oriented silicon steel laminations has been constructed as a prototype for a muon synchrotron ramping at 400 Hz. Following the practice in large 3 phase transformers and our own OPERA-2D simulations, joints are mitered to take advantage of the magnetic properties of the steel which are most effective in the direction in which the steel was rolled. Measurements with a Hysteresigraph 5500 and Epstein Frame show a high magnetic permeability which minimizes stored energy in the yoke so the magnet can ramp quickly with modest voltage. A power supply with a fast IGBT switch and a polypropylene capacitor was constructed. Coils are wound with 12 gauge copper wire which will eventually be cooled with with water flowing in stainless steel tubes. The magnetic field was measured with an F. W. Bell 5180 peak sensing Hall Probe connected to a Tektronics TDS3054B oscilloscope.

THPPD049	Conceptual Design of a Superconducting Septum for FFAGs	3620
	H. Witte BNL, Upton, Long Island, New York, USA M. Aslaninejad, J. Pasternak Imperial College of Science and Technology, Department of Physics, London, United Kingdom K.J. Peach, T. Yokoi JAI, Oxford, United Kingdom
	Funding: This work was supported by STFC grant ST/G008531/1 and EPSRC Grant EP/E032869/1. The fixed magnetic field in FFAG (Fixed Field Alternating Gradient) accelerators means that particles can be accelerated very rapidly. This makes them attractive candidates for many applications, for example for accelerating muons for a neutrino factory or for charged particle therapy (CPT). To benefit fully from this the particles have to be extracted at the same rate. In combination with the high magnetic rigidity of the particles this represents a significant challenge, especially where variable energy extraction is required, which implies extraction at variable radius. This paper presents a conceptual design of a 4T superconducting septum for the PAMELA accelerator, which is an FFAG for a combined proton/carbon ion therapy facility. The field in the septum is varied as a function of the horizontal position, which allows variable energy extraction without the need for sweeping of the magnetic field.

Paper

Title

Page

Status of the Non-scaling Fixed Field Alternating Gradient Ring Design for the International Design Study of the Neutrino Factory

241

J.S. Berg, H. Witte
BNL, Upton, Long Island, New York, USA
M. Aslaninejad, J. Pasternak
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
N. Bliss, A.J. Moss
STFC/DL, Daresbury, Warrington, Cheshire, United Kingdom
D.J. Kelliher, S. Machida
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
S.M. Pattalwar
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom

Funding: This manuscript has been authored by employees of Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy.
The International Design Study of the Neutrino Factory is working towards delivering the optimized design of the neutrino factory facility to be presented in the Reference Design Report (RDR) in 2013. In the current baseline design a linear non-scaling fixed field alternating gradient accelerator (FFAG) was chosen as an efficient solution for the final muon acceleration. We describe updates to the design since our previous report*. We report on beam dynamics studies on the lattice. We describe recent work on the engineering for the lattice, and the results of a recent first pass at a cost estimate for the machine. Finally, we describe how an FFAG may be applicable to a lower energy neutrino factory in light of recent experimental results regarding the value of the theta(13) neutrino mixing angle**.
* J. S. Berg et al., in Proceedings of IPAC2011, San Sebastian, Spain, 832.
** F. P. An et al., Phys. Rev. Lett. 10⁸, 171803 (2012); J. K. Ahn et al., arXiv:1204.0626v2 [hep-ex] (2012).

MOEPPB003

Status of the PRISM FFAG Design for the Next Generation Muon-to-Electron Conversion Experiment

79

J. Pasternak, A. Alekou, M. Aslaninejad, R. Chudzinski, L.J. Jenner, A. Kurup, Y. Shi, Y. Uchida
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
R. Appleby, H.L. Owen
UMAN, Manchester, United Kingdom
R.J. Barlow
University of Huddersfield, Huddersfield, United Kingdom
K.M. Hock, B.D. Muratori
Cockcroft Institute, Warrington, Cheshire, United Kingdom
D.J. Kelliher, S. Machida, C.R. Prior
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
Y. Kuno, A. Sato
Osaka University, Osaka, Japan
J.-B. Lagrange, Y. Mori
Kyoto University, Research Reactor Institute, Osaka, Japan
M. Lancaster
UCL, London, United Kingdom
C. Ohmori
KEK, Tokai, Ibaraki, Japan
T. Planche
TRIUMF, Canada's National Laboratory for Particle and Nuclear Physics, Vancouver, Canada
S.L. Smith
STFC/DL/ASTeC, Daresbury, Warrington, Cheshire, United Kingdom
H. Witte
BNL, Upton, Long Island, New York, USA
T. Yokoi
JAI, Oxford, United Kingdom

The PRISM Task Force continues to study high intensity and high quality muon beams needed for next generation lepton flavor violation experiments. In the PRISM case such beams have been proposed to be produced by sending a short proton pulse to a pion production target, capturing the pions and performing RF phase rotation on the resulting muon beam in an FFAG ring. This paper summarizes the current status of the PRISM design obtained by the Task Force. In particular various designs for the PRISM FFAG ring are discussed and their performance compared to the baseline one, the injection/extraction systems and matching to the solenoid channels upstream and downstream of the FFAG ring are presented. The feasibility of the construction of the PRISM system is discussed.

THPPD020

Test of a 1.8 Tesla, 400 Hz Dipole for a Muon Synchrotron

3542

D.J. Summers, L.M. Cremaldi, T.L. Hart, L.P. Perera, M. Reep
UMiss, University, Mississippi, USA
S.U. Hansen, M.L. Lopes
Fermilab, Batavia, USA
J. Reidy
Oxford High School, Mississippi, USA
H. Witte
BNL, Upton, Long Island, New York, USA

Funding: Supported by DE-FG05-91ER40622.
A 1.8 Tesla dipole magnet using 0.011" AK Steel TRAN-COR H-1 grain oriented silicon steel laminations has been constructed as a prototype for a muon synchrotron ramping at 400 Hz. Following the practice in large 3 phase transformers and our own OPERA-2D simulations, joints are mitered to take advantage of the magnetic properties of the steel which are most effective in the direction in which the steel was rolled. Measurements with a Hysteresigraph 5500 and Epstein Frame show a high magnetic permeability which minimizes stored energy in the yoke so the magnet can ramp quickly with modest voltage. A power supply with a fast IGBT switch and a polypropylene capacitor was constructed. Coils are wound with 12 gauge copper wire which will eventually be cooled with with water flowing in stainless steel tubes. The magnetic field was measured with an F. W. Bell 5180 peak sensing Hall Probe connected to a Tektronics TDS3054B oscilloscope.

THPPD049

Conceptual Design of a Superconducting Septum for FFAGs

3620

H. Witte
BNL, Upton, Long Island, New York, USA
M. Aslaninejad, J. Pasternak
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
K.J. Peach, T. Yokoi
JAI, Oxford, United Kingdom

Funding: This work was supported by STFC grant ST/G008531/1 and EPSRC Grant EP/E032869/1.
The fixed magnetic field in FFAG (Fixed Field Alternating Gradient) accelerators means that particles can be accelerated very rapidly. This makes them attractive candidates for many applications, for example for accelerating muons for a neutrino factory or for charged particle therapy (CPT). To benefit fully from this the particles have to be extracted at the same rate. In combination with the high magnetic rigidity of the particles this represents a significant challenge, especially where variable energy extraction is required, which implies extraction at variable radius. This paper presents a conceptual design of a 4T superconducting septum for the PAMELA accelerator, which is an FFAG for a combined proton/carbon ion therapy facility. The field in the septum is varied as a function of the horizontal position, which allows variable energy extraction without the need for sweeping of the magnetic field.