IPAC2012 - List of Authors (Prestemon, S.)

Paper	Title	Page
TUPPP037	Status of the ALS Brightness Upgrade	1692
	C. Steier, B.J. Bailey, A. Biocca, A.T. Black, D. Colomb, N. Li, A. Madur, S. Marks, H. Nishimura, G.C. Pappas, S. Prestemon, D. Robin, S.L. Rossi, T. Scarvie, D. Schlueter, C. Sun, W. Wan LBNL, Berkeley, California, USA
	Funding: Work supported by the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. The Advanced Light Source (ALS) at Berkeley Lab while one of the earliest 3rd generation light sources remains one of the brightest sources for sof x-rays. Another multiyear upgrade of the ALS is currently under way, which includes new and replacement x-ray beamlines, a replacement of many of the original insertion devices and many upgrades to the accelerator. The accelerator upgrade that affects the ALS performance most directly is the ALS brightness upgrade, which will reduce the horizontal emittance from 6.3 to 2.2 nm (2.6 nm effective). This will result in a brightness increase by a factor of three for bendmagnet beamlines and at least a factor of two for insertion device beamlines. Magnets for this upgrade are currently under production and will be installed later this year.

TUPPP070	Next Generation Light Source R&D and Design Studies at LBNL	1762
	J.N. Corlett, B. Austin, K.M. Baptiste, D.L. Bowring, J.M. Byrd, S. De Santis, P. Denes, R.J. Donahue, L.R. Doolittle, P. Emma, D. Filippetto, G. Huang, T. Koettig, S. Kwiatkowski, D. Li, T.P. Lou, H. Nishimura, H.A. Padmore, C. F. Papadopoulos, G.C. Pappas, G. Penn, M. Placidi, S. Prestemon, D. Prosnitz, J. Qiang, A. Ratti, M.W. Reinsch, D. Robin, F. Sannibale, D. Schlueter, R.W. Schoenlein, J.W. Staples, C. Steier, C. Sun, T. Vecchione, M. Venturini, W. Wan, R.P. Wells, R.B. Wilcox, J.S. Wurtele LBNL, Berkeley, California, USA
	Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. LBNL is developing design concepts for a multi-beamline soft x-ray FEL array powered by a superconducting linear accelerator, operating with a high bunch repetition rate of approximately one MHz. The cw superconducting linear accelerator is supplied by an injector based on a high-brightness, high-repetition-rate photocathode electron gun. Electron bunches are distributed from the linac to the array of independently configurable FEL beamlines with nominal bunch rates up to 100 kHz in each FEL, and with even pulse spacing. Individual FELs may be configured for different modes of operation, and each may produce high peak and average brightness x-rays with a flexible pulse format, and with pulse durations ranging from sub-femtoseconds to hundreds of femtoseconds. In this paper we describe conceptual design studies and optimizations. We describe recent developments in the design and performance parameters, and progress in R&D activities.

THPPC035	Final Assembly and Testing of the MICE Superconducting Spectrometer Solenoids	3362
	S.P. Virostek, M.A. Green, T.O. Niinikoski, H. Pan, S. Prestemon LBNL, Berkeley, California, USA R. Preece STFC/RAL, Chilton, Didcot, Oxon, United Kingdom
	Funding: This work was supported by the Office of Science, U.S. Department of Energy under DOE contract number DE-AC02-05CH11231. The Muon Ionization Cooling Experiment (MICE) is an international effort to demonstrate the principle of ionization cooling in a segment of a realistic cooling channel using a muon beam. The experiment is sited at Rutherford Appleton Laboratory in England. A 4-tesla uniform field region at each end of the cooling channel will be provided by a pair of identical, 3-m long spectrometer solenoids. As the beam enters and exits the cooling channel, the emittance will be measured within both the upstream and downstream 400 mm diameter magnet bores. Each magnet consists of a three-coil spectrometer magnet group and a two-coil pair that matches the solenoid uniform field into the adjacent MICE cooling channel. An array of five two-stage cryocoolers and one single-stage cryocooler are used to maintain the temperature of the magnet cold mass, radiation shield and current leads. Previous testing revealed several operational and design issues related to heat leak and quench protection that have since been corrected. Details of the magnet design modifications and their final assembly as well as the results of quench training tests will be presented here.

THPPP093	Progress on MICE RFCC Module	3954
	D. Li, D.L. Bowring, A.J. DeMello, S.A. Gourlay, M.A. Green, N. Li, T.O. Niinikoski, H. Pan, S. Prestemon, S.P. Virostek, M.S. Zisman LBNL, Berkeley, California, USA A.D. Bross, R.H. Carcagno, V. Kashikhin, C. Sylvester Fermilab, Batavia, USA Y. Cao, S. Sun, L. Wang, L. Yin SINAP, Shanghai, People's Republic of China A.B. Chen, B. Guo, L. Li, F.Y. Xu ICST, Harbin, People's Republic of China D.M. Kaplan Illinois Institute of Technology, Chicago, Illinois, USA T.H. Luo, D.J. Summers UMiss, University, Mississippi, USA
	Funding: This work was supported by the Office of Science, U.S. Department of Energy under DOE contract number DE-AC02-05CH11231, US Muon Accelerator Program and NSF MRI award: 0959000. Recent progress on the design and fabrication of the RFCC (RF and Coupling Coil) module for the international MICE (Muon Ionization Cooling Experiment) will be reported. The MICE ionization cooling channel has two RFCC modules; each having four 201-MHz normal conducting RF cavities surrounded by one superconducting coupling coil (solenoid) magnet. The magnet is designed to be cooled by 3 cryocoolers. Fabrication of the RF cavities is complete; preparation for the cavity electro-polishing, low power RF measurements and tuning are in progress at LBNL. Fabrication of the cold mass of the first coupling coil magnet has been completed in China and the cold mass arrived at LBNL in late 2011. Preparations for testing the cold mass are currently under way at Fermilab. Plans for the RFCC module assembly and integration are being developed and will be described.

Paper

Title

Page

Status of the ALS Brightness Upgrade

1692

C. Steier, B.J. Bailey, A. Biocca, A.T. Black, D. Colomb, N. Li, A. Madur, S. Marks, H. Nishimura, G.C. Pappas, S. Prestemon, D. Robin, S.L. Rossi, T. Scarvie, D. Schlueter, C. Sun, W. Wan
LBNL, Berkeley, California, USA

Funding: Work supported by the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
The Advanced Light Source (ALS) at Berkeley Lab while one of the earliest 3rd generation light sources remains one of the brightest sources for sof x-rays. Another multiyear upgrade of the ALS is currently under way, which includes new and replacement x-ray beamlines, a replacement of many of the original insertion devices and many upgrades to the accelerator. The accelerator upgrade that affects the ALS performance most directly is the ALS brightness upgrade, which will reduce the horizontal emittance from 6.3 to 2.2 nm (2.6 nm effective). This will result in a brightness increase by a factor of three for bendmagnet beamlines and at least a factor of two for insertion device beamlines. Magnets for this upgrade are currently under production and will be installed later this year.

TUPPP070

Next Generation Light Source R&D and Design Studies at LBNL

1762

J.N. Corlett, B. Austin, K.M. Baptiste, D.L. Bowring, J.M. Byrd, S. De Santis, P. Denes, R.J. Donahue, L.R. Doolittle, P. Emma, D. Filippetto, G. Huang, T. Koettig, S. Kwiatkowski, D. Li, T.P. Lou, H. Nishimura, H.A. Padmore, C. F. Papadopoulos, G.C. Pappas, G. Penn, M. Placidi, S. Prestemon, D. Prosnitz, J. Qiang, A. Ratti, M.W. Reinsch, D. Robin, F. Sannibale, D. Schlueter, R.W. Schoenlein, J.W. Staples, C. Steier, C. Sun, T. Vecchione, M. Venturini, W. Wan, R.P. Wells, R.B. Wilcox, J.S. Wurtele
LBNL, Berkeley, California, USA

Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
LBNL is developing design concepts for a multi-beamline soft x-ray FEL array powered by a superconducting linear accelerator, operating with a high bunch repetition rate of approximately one MHz. The cw superconducting linear accelerator is supplied by an injector based on a high-brightness, high-repetition-rate photocathode electron gun. Electron bunches are distributed from the linac to the array of independently configurable FEL beamlines with nominal bunch rates up to 100 kHz in each FEL, and with even pulse spacing. Individual FELs may be configured for different modes of operation, and each may produce high peak and average brightness x-rays with a flexible pulse format, and with pulse durations ranging from sub-femtoseconds to hundreds of femtoseconds. In this paper we describe conceptual design studies and optimizations. We describe recent developments in the design and performance parameters, and progress in R&D activities.

THPPC035

Final Assembly and Testing of the MICE Superconducting Spectrometer Solenoids

3362

S.P. Virostek, M.A. Green, T.O. Niinikoski, H. Pan, S. Prestemon
LBNL, Berkeley, California, USA
R. Preece
STFC/RAL, Chilton, Didcot, Oxon, United Kingdom

Funding: This work was supported by the Office of Science, U.S. Department of Energy under DOE contract number DE-AC02-05CH11231.
The Muon Ionization Cooling Experiment (MICE) is an international effort to demonstrate the principle of ionization cooling in a segment of a realistic cooling channel using a muon beam. The experiment is sited at Rutherford Appleton Laboratory in England. A 4-tesla uniform field region at each end of the cooling channel will be provided by a pair of identical, 3-m long spectrometer solenoids. As the beam enters and exits the cooling channel, the emittance will be measured within both the upstream and downstream 400 mm diameter magnet bores. Each magnet consists of a three-coil spectrometer magnet group and a two-coil pair that matches the solenoid uniform field into the adjacent MICE cooling channel. An array of five two-stage cryocoolers and one single-stage cryocooler are used to maintain the temperature of the magnet cold mass, radiation shield and current leads. Previous testing revealed several operational and design issues related to heat leak and quench protection that have since been corrected. Details of the magnet design modifications and their final assembly as well as the results of quench training tests will be presented here.

THPPP093

Progress on MICE RFCC Module

3954

D. Li, D.L. Bowring, A.J. DeMello, S.A. Gourlay, M.A. Green, N. Li, T.O. Niinikoski, H. Pan, S. Prestemon, S.P. Virostek, M.S. Zisman
LBNL, Berkeley, California, USA
A.D. Bross, R.H. Carcagno, V. Kashikhin, C. Sylvester
Fermilab, Batavia, USA
Y. Cao, S. Sun, L. Wang, L. Yin
SINAP, Shanghai, People's Republic of China
A.B. Chen, B. Guo, L. Li, F.Y. Xu
ICST, Harbin, People's Republic of China
D.M. Kaplan
Illinois Institute of Technology, Chicago, Illinois, USA
T.H. Luo, D.J. Summers
UMiss, University, Mississippi, USA

Funding: This work was supported by the Office of Science, U.S. Department of Energy under DOE contract number DE-AC02-05CH11231, US Muon Accelerator Program and NSF MRI award: 0959000.
Recent progress on the design and fabrication of the RFCC (RF and Coupling Coil) module for the international MICE (Muon Ionization Cooling Experiment) will be reported. The MICE ionization cooling channel has two RFCC modules; each having four 201-MHz normal conducting RF cavities surrounded by one superconducting coupling coil (solenoid) magnet. The magnet is designed to be cooled by 3 cryocoolers. Fabrication of the RF cavities is complete; preparation for the cavity electro-polishing, low power RF measurements and tuning are in progress at LBNL. Fabrication of the cold mass of the first coupling coil magnet has been completed in China and the cold mass arrived at LBNL in late 2011. Preparations for testing the cold mass are currently under way at Fermilab. Plans for the RFCC module assembly and integration are being developed and will be described.