IBIC2013 - List of Authors (Sydlo, C.)

Paper

Title

Page

Development Status of Optical Synchronization for the European XFEL

135

C. Sydlo, M.K. Czwalinna, M. Felber, C. Gerth, T. Lamb, H. Schlarb, S. Schulz, F. Zummack
DESY, Hamburg, Germany
S. Jabłoński
Warsaw University of Technology, Institute of Electronic Systems, Warsaw, Poland

Precise timing synchronization on the femtosecond timescale is crucial for time resolved experiments at modern free-electron lasers (FELs) like FLASH and the upcoming European XFEL. The required precision can only be achieved by a laser-based synchronization system. The pulsed laser-based scheme at FLASH, based on the distribution of femtosecond laser pulses over actively stabilized optical fibers, has evolved over the years from a prototype setup to a mature and reliable system. At the same time, the present implementation serves as prototype for the synchronization infrastructure at the European XFEL. Due to a factor of ten increase of the length of the accelerator and an increased number of timing-critical subsystems, new challenges arise. This paper reports on the current development progress of the XFEL optical synchronization, discusses major complications and their solutions.

MOPC33

Status of the Fiber Link Stabilization Units at FLASH

139

F. Zummack, M.K. Czwalinna, M. Felber, T. Lamb, H. Schlarb, S. Schulz, C. Sydlo
DESY, Hamburg, Germany
S. Jabłoński
Warsaw University of Technology, Institute of Electronic Systems, Warsaw, Poland

State-of-the-art X-ray photon science with modern free-electron lasers (FEL) like FLASH and the upcoming European X-ray Free-Electron Laser Facility (XFEL) requires timing with femtosecond accuracy. For this purpose a sophisticated pulsed optical synchronization system distributes precise timing via length-stabilized fiber links throughout the entire FEL. Stations to be synchronized comprise bunch arrival time monitors, RF stations and optical cross-correlators for external lasers. The different requirements of all those stations have to be met by one optical link-stabilization-unit (LSU) design, compensating drifts and jitter in the distribution system down to a fs-level. Five years of LSU operation at FLASH have led to numerous enhancements resulting in an elaborate system. This paper presents these enhancements, their impact on synchronization performance and the latest state of the LSUs.

TUPC29

Grounded Coplanar Waveguide Transmission Lines as Pickups for Beam Position Monitoring in Particle Accelerators

438

A. Penirschke, A. Angelovski, R. Jakoby
TU Darmstadt, Darmstadt, Germany
C. Gerth, U. Mavrič, D. Nölle, C. Sydlo, S. Vilcins
DESY, Hamburg, Germany

Funding: The work was supported by the MSK group at DESY Hamburg. The authors would like to thank the CST AG for providing the CST Software Package.
Energy beam position monitors (EBPM) based on grounded co-planar waveguide (GCPW) transmission lines have been designed for installation in the dispersive sections of the bunch compressor chicanes at the European XFEL. In combination with beam position monitors at the entrance and exit of the bunch compressor chicanes, measurements of the beam energy with single bunch resolution are feasible. The EBPM consists of transversely mounted stripline pickups in a rectangular beam pipe section. The signal detection for the measurement of the phases of the pulses at each end of the pickups is based on the standard down-conversion and phase detection scheme used for the low-level RF-system. A measurement resolution within the lower micrometer range can be achieved for input signal reflections at the pickup of less than -25 dB at 3 GHz. In this paper, simulation results of a novel pickup geometry utilized with GCPW pickup structures and optimized transitions to perpendicular mounted coaxial connectors are presented. The simulation results exhibit small reflection coefficients with reflected signal components having less than 2% of the peak voltage signal.

TUPC33

Femtosecond Stable Laser-to-RF Phase Detection for Optical Synchronization Systems

447

T. Lamb, M.K. Czwalinna, M. Felber, C. Gerth, H. Schlarb, S. Schulz, C. Sydlo, M. Titberidze, F. Zummack
DESY, Hamburg, Germany
E. Janas
Warsaw University of Technology, Institute of Electronic Systems, Warsaw, Poland
J. Szewiński
NCBJ, Świerk/Otwock, Poland

Optical reference distributions have become an indispensable asset for femtosecond precision synchronization of free-electron lasers. At FLASH and for the future European XFEL, laser pulses are distributed over large distances in round-trip time stabilized fibers to all critical facility sub-systems. Novel Laser-to-RF phase detectors will be used to provide ultra phase stable and long-term drift free microwave signals for the accelerator RF controls. In this paper, we present the recent progress on the design of a fully integrated and engineered version of the L2RF phase detector, together with first experimental results demonstrating so-far unrivaled performance.

Poster TUPC33 [18.910 MB]

WEPC32

Past, Present and Future Aspects of Laser-Based Synchronization at FLASH

753

S. Schulz, M. Bousonville, M.K. Czwalinna, M. Felber, M. Heuer, T. Lamb, J. Müller, P. Peier, S. Ruzin, H. Schlarb, B. Steffen, C. Sydlo, F. Zummack
DESY, Hamburg, Germany
T. Kozak, P. Predki
TUL-DMCS, Łódź, Poland
A. Kuhl
Uni HH, Hamburg, Germany

Free-electron lasers, like FLASH and the upcoming European XFEL, are capable of producing XUV and X-ray pulses of a few femtoseconds duration. For time-resolved pump-probe experiments and the externally seeded operation mode it is crucial not only to stabilize the arrival time of the electron bunches, but also to achieve a synchronization accuracy of external lasers on the same timescale. This can only be realized with a laser-based synchronization infrastructure. At FLASH, a periodic femtosecond laser pulse train is transmitted over actively stabilized optical fibers to the critical subsystems. In this paper we report on the present status and performance of the system, as well as its imminent upgrades and new installations. These include the connection of FLASH2, electron bunch arrival time monitors for low charges, a new master laser pulse distribution scheme, all-optical synchronization of the pump-probe laser and arrival time measurements of the UV pulses on the e-gun photocathode. Along with the coming connection of the acceleration modules to the master laser and the switch of the low-level hardware to the uTCA platform, an outlook to improved feedback strategies is given.

WEPC40

Pickup Signal Improvement for High Bandwidth BAMs for FLASH and European - XFEL

778

A. Angelovski, R. Jakoby, A. Penirschke
TU Darmstadt, Darmstadt, Germany
M.K. Czwalinna, H. Schlarb, C. Sydlo
DESY, Hamburg, Germany
T. Weiland
TEMF, TU Darmstadt, Darmstadt, Germany

In order to measure the arrival time of the electron bunches in low (20 pC) and high (1 nC) charge operation mode, new high bandwidth pickups were developed as a part of the Bunch Arrival-time Monitors (BAMs) for FLASH at DESY *. The pickup signal is transported via radiation resistant coaxial cables to the electro-optic modulator (EOM) **. Due to the high losses of the 40 GHz RF front-end the signal in the RF path is attenuated well below the optimal operation voltage of the EOM. To improve the overall performance, the signal strength of the induced pickup signal needs to be increased and at the same time the losses in the RF front-end significantly reduced. In this paper, the analysis towards improving the induced pickup signal strength is presented. Simulations are performed with the CST STUDIO SUITE package and the results are compared with the state of the art high bandwidth pickups.
* A. Angelovski et al., Phys. Rev. ST Accel. Beams 15, 112803 (2012)
** A. Penirschke et al., Proc. of IBIC2012, Tsukuba, Japan (2012)

WEPC41

Comparative Analysis of Different Electro-Optical Intensity Modulator Candidates for the New 40 GHz Bunch Arrival Time Monitor System for FLASH and European XFEL

782

A. Kuhl, J. Rönsch-Schulenburg, J. Roßbach
Uni HH, Hamburg, Germany
M.K. Czwalinna, C. Gerth, H. Schlarb, C. Sydlo
DESY, Hamburg, Germany
S. Schnepp
ETH Zurich, Institute of Electromagnetic Fields (IFH), Zurich, Switzerland
T. Weiland
TEMF, TU Darmstadt, Darmstadt, Germany

Funding: The work is supported by Federal Ministry of Education and Research of Germany (BMBF) within FSP 301 under the contract numbers 05K10GU2 and 05K10RDA.
The currently installed Bunch Arrival time Monitors (BAMs) at the Free electron LASer in Hamburg (FLASH) achieved a time resolution of less than 10 fs for bunch charges higher than 500 pC. In order to achieve single spike FEL pulses at FLASH, electron bunch charges down to 20 pC are of interest. With these BAMs the required time resolution is not reachable for bunch charges below 500 pC. Therefore new pickups with a bandwidth of up to 40 GHz are designed and manufactured*. The signal evaluation takes place with a time-stabilized reference laser pulse train which is modulated with an Electro-Optical intensity Modulator (EOM). The new BAM system also requires new EOMs for the electro-optical frontend. The available selection of commercial EOM candidates for the new frontend is very limited. In this paper we present a comparison between different EOM candidates for the new electro optical frontend.
* A. Angelovski et al. Proceedings Phys. Rev ST AB, DOI:10.1103/PhysRevSTAB.15.112803

Poster WEPC41 [0.619 MB]

Paper	Title	Page
MOPC32	Development Status of Optical Synchronization for the European XFEL	135
	C. Sydlo, M.K. Czwalinna, M. Felber, C. Gerth, T. Lamb, H. Schlarb, S. Schulz, F. Zummack DESY, Hamburg, Germany S. Jabłoński Warsaw University of Technology, Institute of Electronic Systems, Warsaw, Poland
	Precise timing synchronization on the femtosecond timescale is crucial for time resolved experiments at modern free-electron lasers (FELs) like FLASH and the upcoming European XFEL. The required precision can only be achieved by a laser-based synchronization system. The pulsed laser-based scheme at FLASH, based on the distribution of femtosecond laser pulses over actively stabilized optical fibers, has evolved over the years from a prototype setup to a mature and reliable system. At the same time, the present implementation serves as prototype for the synchronization infrastructure at the European XFEL. Due to a factor of ten increase of the length of the accelerator and an increased number of timing-critical subsystems, new challenges arise. This paper reports on the current development progress of the XFEL optical synchronization, discusses major complications and their solutions.

MOPC33	Status of the Fiber Link Stabilization Units at FLASH	139
	F. Zummack, M.K. Czwalinna, M. Felber, T. Lamb, H. Schlarb, S. Schulz, C. Sydlo DESY, Hamburg, Germany S. Jabłoński Warsaw University of Technology, Institute of Electronic Systems, Warsaw, Poland
	State-of-the-art X-ray photon science with modern free-electron lasers (FEL) like FLASH and the upcoming European X-ray Free-Electron Laser Facility (XFEL) requires timing with femtosecond accuracy. For this purpose a sophisticated pulsed optical synchronization system distributes precise timing via length-stabilized fiber links throughout the entire FEL. Stations to be synchronized comprise bunch arrival time monitors, RF stations and optical cross-correlators for external lasers. The different requirements of all those stations have to be met by one optical link-stabilization-unit (LSU) design, compensating drifts and jitter in the distribution system down to a fs-level. Five years of LSU operation at FLASH have led to numerous enhancements resulting in an elaborate system. This paper presents these enhancements, their impact on synchronization performance and the latest state of the LSUs.

TUPC29	Grounded Coplanar Waveguide Transmission Lines as Pickups for Beam Position Monitoring in Particle Accelerators	438
	A. Penirschke, A. Angelovski, R. Jakoby TU Darmstadt, Darmstadt, Germany C. Gerth, U. Mavrič, D. Nölle, C. Sydlo, S. Vilcins DESY, Hamburg, Germany
	Funding: The work was supported by the MSK group at DESY Hamburg. The authors would like to thank the CST AG for providing the CST Software Package. Energy beam position monitors (EBPM) based on grounded co-planar waveguide (GCPW) transmission lines have been designed for installation in the dispersive sections of the bunch compressor chicanes at the European XFEL. In combination with beam position monitors at the entrance and exit of the bunch compressor chicanes, measurements of the beam energy with single bunch resolution are feasible. The EBPM consists of transversely mounted stripline pickups in a rectangular beam pipe section. The signal detection for the measurement of the phases of the pulses at each end of the pickups is based on the standard down-conversion and phase detection scheme used for the low-level RF-system. A measurement resolution within the lower micrometer range can be achieved for input signal reflections at the pickup of less than -25 dB at 3 GHz. In this paper, simulation results of a novel pickup geometry utilized with GCPW pickup structures and optimized transitions to perpendicular mounted coaxial connectors are presented. The simulation results exhibit small reflection coefficients with reflected signal components having less than 2% of the peak voltage signal.

TUPC33	Femtosecond Stable Laser-to-RF Phase Detection for Optical Synchronization Systems	447
	T. Lamb, M.K. Czwalinna, M. Felber, C. Gerth, H. Schlarb, S. Schulz, C. Sydlo, M. Titberidze, F. Zummack DESY, Hamburg, Germany E. Janas Warsaw University of Technology, Institute of Electronic Systems, Warsaw, Poland J. Szewiński NCBJ, Świerk/Otwock, Poland
	Optical reference distributions have become an indispensable asset for femtosecond precision synchronization of free-electron lasers. At FLASH and for the future European XFEL, laser pulses are distributed over large distances in round-trip time stabilized fibers to all critical facility sub-systems. Novel Laser-to-RF phase detectors will be used to provide ultra phase stable and long-term drift free microwave signals for the accelerator RF controls. In this paper, we present the recent progress on the design of a fully integrated and engineered version of the L2RF phase detector, together with first experimental results demonstrating so-far unrivaled performance.
	Poster TUPC33 [18.910 MB]

WEPC32	Past, Present and Future Aspects of Laser-Based Synchronization at FLASH	753
	S. Schulz, M. Bousonville, M.K. Czwalinna, M. Felber, M. Heuer, T. Lamb, J. Müller, P. Peier, S. Ruzin, H. Schlarb, B. Steffen, C. Sydlo, F. Zummack DESY, Hamburg, Germany T. Kozak, P. Predki TUL-DMCS, Łódź, Poland A. Kuhl Uni HH, Hamburg, Germany
	Free-electron lasers, like FLASH and the upcoming European XFEL, are capable of producing XUV and X-ray pulses of a few femtoseconds duration. For time-resolved pump-probe experiments and the externally seeded operation mode it is crucial not only to stabilize the arrival time of the electron bunches, but also to achieve a synchronization accuracy of external lasers on the same timescale. This can only be realized with a laser-based synchronization infrastructure. At FLASH, a periodic femtosecond laser pulse train is transmitted over actively stabilized optical fibers to the critical subsystems. In this paper we report on the present status and performance of the system, as well as its imminent upgrades and new installations. These include the connection of FLASH2, electron bunch arrival time monitors for low charges, a new master laser pulse distribution scheme, all-optical synchronization of the pump-probe laser and arrival time measurements of the UV pulses on the e-gun photocathode. Along with the coming connection of the acceleration modules to the master laser and the switch of the low-level hardware to the uTCA platform, an outlook to improved feedback strategies is given.

WEPC40	Pickup Signal Improvement for High Bandwidth BAMs for FLASH and European - XFEL	778
	A. Angelovski, R. Jakoby, A. Penirschke TU Darmstadt, Darmstadt, Germany M.K. Czwalinna, H. Schlarb, C. Sydlo DESY, Hamburg, Germany T. Weiland TEMF, TU Darmstadt, Darmstadt, Germany
	In order to measure the arrival time of the electron bunches in low (20 pC) and high (1 nC) charge operation mode, new high bandwidth pickups were developed as a part of the Bunch Arrival-time Monitors (BAMs) for FLASH at DESY . The pickup signal is transported via radiation resistant coaxial cables to the electro-optic modulator (EOM) . Due to the high losses of the 40 GHz RF front-end the signal in the RF path is attenuated well below the optimal operation voltage of the EOM. To improve the overall performance, the signal strength of the induced pickup signal needs to be increased and at the same time the losses in the RF front-end significantly reduced. In this paper, the analysis towards improving the induced pickup signal strength is presented. Simulations are performed with the CST STUDIO SUITE package and the results are compared with the state of the art high bandwidth pickups. A. Angelovski et al., Phys. Rev. ST Accel. Beams 15, 112803 (2012) ** A. Penirschke et al., Proc. of IBIC2012, Tsukuba, Japan (2012)

WEPC41	Comparative Analysis of Different Electro-Optical Intensity Modulator Candidates for the New 40 GHz Bunch Arrival Time Monitor System for FLASH and European XFEL	782
	A. Kuhl, J. Rönsch-Schulenburg, J. Roßbach Uni HH, Hamburg, Germany M.K. Czwalinna, C. Gerth, H. Schlarb, C. Sydlo DESY, Hamburg, Germany S. Schnepp ETH Zurich, Institute of Electromagnetic Fields (IFH), Zurich, Switzerland T. Weiland TEMF, TU Darmstadt, Darmstadt, Germany
	Funding: The work is supported by Federal Ministry of Education and Research of Germany (BMBF) within FSP 301 under the contract numbers 05K10GU2 and 05K10RDA. The currently installed Bunch Arrival time Monitors (BAMs) at the Free electron LASer in Hamburg (FLASH) achieved a time resolution of less than 10 fs for bunch charges higher than 500 pC. In order to achieve single spike FEL pulses at FLASH, electron bunch charges down to 20 pC are of interest. With these BAMs the required time resolution is not reachable for bunch charges below 500 pC. Therefore new pickups with a bandwidth of up to 40 GHz are designed and manufactured. The signal evaluation takes place with a time-stabilized reference laser pulse train which is modulated with an Electro-Optical intensity Modulator (EOM). The new BAM system also requires new EOMs for the electro-optical frontend. The available selection of commercial EOM candidates for the new frontend is very limited. In this paper we present a comparison between different EOM candidates for the new electro optical frontend. A. Angelovski et al. Proceedings Phys. Rev ST AB, DOI:10.1103/PhysRevSTAB.15.112803
	Poster WEPC41 [0.619 MB]