IPAC2018 - List of Authors (Whiteford, C.)

Paper	Title	Page
TUYGBE3	Recent progress of short pulse dielectric two-beam acceleration	640
	J.H. Shao, M.E. Conde, D.S. Doran, W. Gai, W. Liu, N.R. Neveu, J.F. Power, C. Whiteford, E.E. Wisniewski, L.M. Zheng ANL, Argonne, Illinois, USA C.-J. Jing Euclid TechLabs, LLC, Solon, Ohio, USA
	Two-Beam Acceleration (TBA) is a structure-based wakefield acceleration method with the potential to meet the luminosity and cost requirements of a TeV class linear collider. The Argonne Wakefield Accelerator (AWA) facility is developing a dielectric-based short pulse TBA scheme with the potential to withstand high acceleration gradients and to achieve low fabrication cost. Recently, the dielectric short pulse TBA technology was successfully demonstrated using K-band 26 GHz structures, achieving 55 MW output power from the power extractor and 28 MeV/m gradient in the accelerator. To improve the generated rf power, an X-band 11.7 GHz power extractor has been developed, which obtained 10⁵ MW in the high power test. In addition, a novel dielectric disk accelerator (DDA) is currently under investigation to significantly increase the efficiency of linear colliders based on short pulse TBA. Details of these research will be presented in this paper.
	Slides TUYGBE3 [2.219 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUYGBE3
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPMF020	Demonstration of Fast, Single-shot Photocathode QE Mapping Method Using MLA Pattern Beam	1293
	E.E. Wisniewski, M.E. Conde, D.S. Doran, W. Gai, Q. Gao, W. Liu, J.G. Power, C. Whiteford ANL, Argonne, Illinois, USA Q. Gao TUB, Beijing, People's Republic of China G. Ha PAL, Pohang, Republic of Korea A. Halavanau, P. Piot Northern Illinois University, DeKalb, Illinois, USA P. Piot Fermilab, Batavia, Illinois, USA
	Funding: UChicago Argonne, LLC, Operator of Argonne National Laboratory ("Argonne"). Argonne, a U.S.A. Department of Energy Office of Science laboratory, is operated under Contract No. DE-AC02-06CH11357. Quantum efficiency (QE) is the chief figure of merit in the characterization of photocathodes. Semiconductor photocathodes, especially when used in high rep-rate photo-injectors, are known to show QE degradation over time and must be replaced. The total QE is the basic diagnostic which is used widely and is easy to obtain. However, a QE map indicating variations of QE across the cathode surface has greater utility. It can quickly diagnose problems of QE inhomogeneity. Most QE mapping techniques require hours to complete and are thus disruptive to a user facility schedule. A fast, single-shot method has been proposed (citation) using a micro-lens array (MLA) generated QE map. In this paper we report the implementation of the method at Argonne Wakefield Accelerator facility. A micro-lens array (MLA) is used to project an array of beamlets onto the photocathode. The resulting photoelectron beam in the form of an array of electron beamlets is imaged at a YAG screen. Four synchronized measurements are made and the results used to produce a QE map of the photocathode.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPMF020
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPML004	Correction of Emittance Growth Due to Quad Components in Solenoids With Quad Correctors at AWA	1536
	L.M. Zheng, C.-X. Tang TUB, Beijing, People's Republic of China M.E. Conde, D.S. Doran, W. Gai, W. Liu, J.G. Power, J.H. Shao, C. Whiteford, E.E. Wisniewski ANL, Argonne, Illinois, USA
	An asymmetrical electron beam is observed on the drive beamline at Argonne Wakefield Accelerator (AWA) due to the quad components in the solenoids. An ASTRA simulation shows that the emittance will increase when the electron beam passes through solenoids with quad errors. We use two quad correctors to correct this emittance growth. A preliminary emittance correction result is presented in this paper.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPML004
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPML006	Updates of the Argonne Cathode Test-stand	1542
	J.H. Shao, M.E. Conde, D.S. Doran, W. Gai, W. Liu, J.F. Power, C. Whiteford, E.E. Wisniewski, L.M. Zheng ANL, Argonne, Illinois, USA S.P. Antipov, G. Chen, E. Gomez, C.-J. Jing Euclid TechLabs, LLC, Solon, Ohio, USA S.V. Baryshev Michigan State University, East Lansing, Michigan, USA
	The Argonne Cathode Test-stand (ACT) is a unique testbed to develop cathodes and to conduct fundamental surface study under ultra-high rf field (up to 700 MV/m with pin-shaped cathodes). The test-stand consists of an L-band 1.3 GHz single-cell photocathode rf gun and a field emission (FE) imaging system to locate emitters with a resolution of ∼20 𝜇m. In the recent upgrade, UV laser has been introduced to improve the imaging system and to significantly expand the ACT towards photoemission and laser-assisted field emission research. In addition, a load-lock system has been added to the beam line to expedite the cathode switching period. The paper will present details of the upgrade as well as experiments planned in the near future.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPML006
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPML007	Short Pulse High Power RF Generation with an X-Band Dielectric Power Extractor	1546
	J.H. Shao, M.E. Conde, D.S. Doran, W. Gai, W. Liu, N.R. Neveu, J.F. Power, C. Whiteford, E.E. Wisniewski, L.M. Zheng ANL, Argonne, Illinois, USA C.-J. Jing Euclid TechLabs, LLC, Solon, Ohio, USA
	Short pulse high power rf generation is one of the key technologies for the Argonne Flexible Linear Collider (AFLC), a proposed 3 TeV electron-positron linear collider based on two-beam acceleration (TBA) scheme. Compared with metallic power extractors, dielectric structures have the potential to achieve lower fabrication cost and to withstand higher gradient. Recently, an X-band dielectric power extractor (a.k.a, DPETS) has been developed at the Argonne Wakefield Accelerator (AWA) facility and achieved 10⁵ MW output power when driven by a high charge 8-bunch train separated by 770 ps. The design, the cold test measurement, the preliminary high power test results, and the structure inspection will be presented in this paper.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPML007
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPMF048	Bunch Length Measurements Using CTR at the AWA with Comparison to Simulation	4166
	N.R. Neveu IIT, Chicago, Illinois, USA S.P. Antipov Euclid TechLabs, LLC, Solon, Ohio, USA A. Halavanau, P. Piot Northern Illinois University, DeKalb, Illinois, USA P. Piot Fermilab, Batavia, Illinois, USA J.G. Power, C. Whiteford, E.E. Wisniewski ANL, Argonne, Illinois, USA L.K. Spentzouris Illinois Institute of Technology, Chicago, Illinois, USA
	Funding: This work is funded by the DOE Office of Science, grant no. DE-SC0015479, and contract No. DE-AC02- 06CH11357. In this paper we present electron bunch length measurements at the Argonne Wakefield Accelerator (AWA) photoinjector facility. The AWA accelerator has a large dynamic charge density range, with electron beam charge varying between 0.1 nC - 100 nC, and laser spot size diameter at the cathode between 0.1 mm - 18 mm. The bunch length measurements were taken at different charge densities using a metallic screen and a Martin-Puplett interferometer to perform autocorrelation scans of the corresponding coherent transition radiation (CTR). A liquid helium-cooled 4K bolometer was used to register the interferometer signal. The experimental results are compared with Impact-T and OPAL-T numerical simulations.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPMF048
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Recent progress of short pulse dielectric two-beam acceleration

640

J.H. Shao, M.E. Conde, D.S. Doran, W. Gai, W. Liu, N.R. Neveu, J.F. Power, C. Whiteford, E.E. Wisniewski, L.M. Zheng
ANL, Argonne, Illinois, USA
C.-J. Jing
Euclid TechLabs, LLC, Solon, Ohio, USA

Two-Beam Acceleration (TBA) is a structure-based wakefield acceleration method with the potential to meet the luminosity and cost requirements of a TeV class linear collider. The Argonne Wakefield Accelerator (AWA) facility is developing a dielectric-based short pulse TBA scheme with the potential to withstand high acceleration gradients and to achieve low fabrication cost. Recently, the dielectric short pulse TBA technology was successfully demonstrated using K-band 26 GHz structures, achieving 55 MW output power from the power extractor and 28 MeV/m gradient in the accelerator. To improve the generated rf power, an X-band 11.7 GHz power extractor has been developed, which obtained 10⁵ MW in the high power test. In addition, a novel dielectric disk accelerator (DDA) is currently under investigation to significantly increase the efficiency of linear colliders based on short pulse TBA. Details of these research will be presented in this paper.

Slides TUYGBE3 [2.219 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUYGBE3

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPMF020

Demonstration of Fast, Single-shot Photocathode QE Mapping Method Using MLA Pattern Beam

1293

E.E. Wisniewski, M.E. Conde, D.S. Doran, W. Gai, Q. Gao, W. Liu, J.G. Power, C. Whiteford
ANL, Argonne, Illinois, USA
Q. Gao
TUB, Beijing, People's Republic of China
G. Ha
PAL, Pohang, Republic of Korea
A. Halavanau, P. Piot
Northern Illinois University, DeKalb, Illinois, USA
P. Piot
Fermilab, Batavia, Illinois, USA

Funding: UChicago Argonne, LLC, Operator of Argonne National Laboratory ("Argonne"). Argonne, a U.S.A. Department of Energy Office of Science laboratory, is operated under Contract No. DE-AC02-06CH11357.
Quantum efficiency (QE) is the chief figure of merit in the characterization of photocathodes. Semiconductor photocathodes, especially when used in high rep-rate photo-injectors, are known to show QE degradation over time and must be replaced. The total QE is the basic diagnostic which is used widely and is easy to obtain. However, a QE map indicating variations of QE across the cathode surface has greater utility. It can quickly diagnose problems of QE inhomogeneity. Most QE mapping techniques require hours to complete and are thus disruptive to a user facility schedule. A fast, single-shot method has been proposed (citation) using a micro-lens array (MLA) generated QE map. In this paper we report the implementation of the method at Argonne Wakefield Accelerator facility. A micro-lens array (MLA) is used to project an array of beamlets onto the photocathode. The resulting photoelectron beam in the form of an array of electron beamlets is imaged at a YAG screen. Four synchronized measurements are made and the results used to produce a QE map of the photocathode.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPMF020

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPML004

Correction of Emittance Growth Due to Quad Components in Solenoids With Quad Correctors at AWA

1536

L.M. Zheng, C.-X. Tang
TUB, Beijing, People's Republic of China
M.E. Conde, D.S. Doran, W. Gai, W. Liu, J.G. Power, J.H. Shao, C. Whiteford, E.E. Wisniewski
ANL, Argonne, Illinois, USA

An asymmetrical electron beam is observed on the drive beamline at Argonne Wakefield Accelerator (AWA) due to the quad components in the solenoids. An ASTRA simulation shows that the emittance will increase when the electron beam passes through solenoids with quad errors. We use two quad correctors to correct this emittance growth. A preliminary emittance correction result is presented in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPML004

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPML006

Updates of the Argonne Cathode Test-stand

1542

J.H. Shao, M.E. Conde, D.S. Doran, W. Gai, W. Liu, J.F. Power, C. Whiteford, E.E. Wisniewski, L.M. Zheng
ANL, Argonne, Illinois, USA
S.P. Antipov, G. Chen, E. Gomez, C.-J. Jing
Euclid TechLabs, LLC, Solon, Ohio, USA
S.V. Baryshev
Michigan State University, East Lansing, Michigan, USA

The Argonne Cathode Test-stand (ACT) is a unique testbed to develop cathodes and to conduct fundamental surface study under ultra-high rf field (up to 700 MV/m with pin-shaped cathodes). The test-stand consists of an L-band 1.3 GHz single-cell photocathode rf gun and a field emission (FE) imaging system to locate emitters with a resolution of ∼20 𝜇m. In the recent upgrade, UV laser has been introduced to improve the imaging system and to significantly expand the ACT towards photoemission and laser-assisted field emission research. In addition, a load-lock system has been added to the beam line to expedite the cathode switching period. The paper will present details of the upgrade as well as experiments planned in the near future.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPML006

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPML007

Short Pulse High Power RF Generation with an X-Band Dielectric Power Extractor

1546

J.H. Shao, M.E. Conde, D.S. Doran, W. Gai, W. Liu, N.R. Neveu, J.F. Power, C. Whiteford, E.E. Wisniewski, L.M. Zheng
ANL, Argonne, Illinois, USA
C.-J. Jing
Euclid TechLabs, LLC, Solon, Ohio, USA

Short pulse high power rf generation is one of the key technologies for the Argonne Flexible Linear Collider (AFLC), a proposed 3 TeV electron-positron linear collider based on two-beam acceleration (TBA) scheme. Compared with metallic power extractors, dielectric structures have the potential to achieve lower fabrication cost and to withstand higher gradient. Recently, an X-band dielectric power extractor (a.k.a, DPETS) has been developed at the Argonne Wakefield Accelerator (AWA) facility and achieved 10⁵ MW output power when driven by a high charge 8-bunch train separated by 770 ps. The design, the cold test measurement, the preliminary high power test results, and the structure inspection will be presented in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUPML007

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPMF048

Bunch Length Measurements Using CTR at the AWA with Comparison to Simulation

4166

N.R. Neveu
IIT, Chicago, Illinois, USA
S.P. Antipov
Euclid TechLabs, LLC, Solon, Ohio, USA
A. Halavanau, P. Piot
Northern Illinois University, DeKalb, Illinois, USA
P. Piot
Fermilab, Batavia, Illinois, USA
J.G. Power, C. Whiteford, E.E. Wisniewski
ANL, Argonne, Illinois, USA
L.K. Spentzouris
Illinois Institute of Technology, Chicago, Illinois, USA

Funding: This work is funded by the DOE Office of Science, grant no. DE-SC0015479, and contract No. DE-AC02- 06CH11357.
In this paper we present electron bunch length measurements at the Argonne Wakefield Accelerator (AWA) photoinjector facility. The AWA accelerator has a large dynamic charge density range, with electron beam charge varying between 0.1 nC - 100 nC, and laser spot size diameter at the cathode between 0.1 mm - 18 mm. The bunch length measurements were taken at different charge densities using a metallic screen and a Martin-Puplett interferometer to perform autocorrelation scans of the corresponding coherent transition radiation (CTR). A liquid helium-cooled 4K bolometer was used to register the interferometer signal. The experimental results are compared with Impact-T and OPAL-T numerical simulations.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPMF048

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)