IPAC2018 - List of Authors (Gerigk, F.)

Paper	Title	Page
MOYGB1	Status and Future Strategy for Advanced High Power Microwave Sources for Accelerators	12
	F. Gerigk CERN, Geneva, Switzerland
	The need for more energy efficient high power microwave devices for accelerator applications continues to increase. This is important for development of cost effective accelerator designs that are coming up in the near future. Efforts are already in place to design new devices that could stretch the limits of RF power conversion to the highest levels possible. Devices including new technologies and design innovations like multi beam, increased number of cavities designs are being considered. Advances in the application of solid state amplifiers to accelerators are also being realized. This invited talk will cover the recent advances and status of such efforts. It will discuss future needs and a strategy for pursuing these efforts on a faster time scale for the benefit of the accelerator community.
	Slides MOYGB1 [11.575 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOYGB1
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPMF036	FCC-ee Hybrid RF Scheme	173
	Sh. Gorgi Zadeh, U. van Rienen Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany R. Calaga, F. Gerigk CERN, Geneva, Switzerland
	Funding: Research supported by the FCC design study For FCC-ee, the range of beam energies and beam currents is large between each mode of operation, all scaled to an available 50 MW maximum power per beam. The two limiting scenarios for the RF system design are at low energy (45 GeV) with high beam current (1.45 A) and the highest energy (182.5 GeV) with a radiation loss reaching 8.92 GeV per turn. In this paper, RF staging with a hybrid scheme using both 400 MHz and 800 MHz is proposed to mitigate the requirements on the two extremes. Relevant comparisons are made with respect to using only a single frequency for all modes.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOPMF036
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPMK105	PERLE - Lattice Design and Beam Dynamics Studies	4556
	S.A. Bogacz, D. Douglas, F.E. Hannon, A. Hutton, F. Marhauser, R.A. Rimmer, Y. Roblin, C. Tennant JLab, Newport News, Virginia, USA D. Angal-Kalinin, J.W. McKenzie, B.L. Militsyn, P.H. Williams Cockcroft Institute, Warrington, Cheshire, United Kingdom G. Arduini, O.S. Brüning, R. Calaga, K.M. Dr. Schirm, F. Gerigk, B.J. Holzer, E. Jensen, A. Milanese, E. Montesinos, D. Pellegrini, P.A. Thonet, A. Valloni CERN, Geneva, Switzerland S. Bousson, D. Longuevergne, G. Olivier, G. Olry IPN, Orsay, France I. Chaikovska, W. Kaabi, A. Stocchi, C. Vallerand LAL, Orsay, France B. Hounsell, M. Klein, U.K. Klein, P. Kostka, C.P. Welsch The University of Liverpool, Liverpool, United Kingdom E.B. Levichev, Yu.A. Pupkov BINP SB RAS, Novosibirsk, Russia
	Funding: Work has been authored by Jefferson Science Associates, LLC under Contract No. DE-AC05-06OR23177 with the U.S. Department of Energy. PERLE (Powerful ERL for Experiments) is a novel ERL test facility, initially proposed to validate choices for a 60 GeV ERL foreseen in the design of the LHeC and the FCC-eh. Its main thrust is to probe high current, CW, multi-pass operation with superconducting cavities at 802 MHz (and perhaps testing other frequencies of interest). With very high virtual beam power (~ 10 MW), PERLE offers an opportunity for controllable study of every beam dynamic effect of interest in the next generation of ERL design; becoming a ‘stepping stone' between present state-of-art 1 MW ERLs and future 100 MW scale applications. PERLE design features Flexible Momentum Compaction lattice architecture for six vertically stacked return arcs and a high-current, 6 MeV, photo-injector. With only one pair of 4 cavity cryomodules, 400 MeV beam energy can be reached in 3 re-circulation passes, with beam currents in excess of 15 mA. The beam is decelerated in 3 consecutive passes back to the injection energy, transferring virtually stored energy back to the RF. This unique facility will serve as a test-bed for high current ERL technologies, as well as a user facility in low energy electron and photon physics.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPMK105
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Status and Future Strategy for Advanced High Power Microwave Sources for Accelerators

12

F. Gerigk
CERN, Geneva, Switzerland

The need for more energy efficient high power microwave devices for accelerator applications continues to increase. This is important for development of cost effective accelerator designs that are coming up in the near future. Efforts are already in place to design new devices that could stretch the limits of RF power conversion to the highest levels possible. Devices including new technologies and design innovations like multi beam, increased number of cavities designs are being considered. Advances in the application of solid state amplifiers to accelerators are also being realized. This invited talk will cover the recent advances and status of such efforts. It will discuss future needs and a strategy for pursuing these efforts on a faster time scale for the benefit of the accelerator community.

Slides MOYGB1 [11.575 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOYGB1

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPMF036

FCC-ee Hybrid RF Scheme

173

Sh. Gorgi Zadeh, U. van Rienen
Rostock University, Faculty of Computer Science and Electrical Engineering, Rostock, Germany
R. Calaga, F. Gerigk
CERN, Geneva, Switzerland

Funding: Research supported by the FCC design study
For FCC-ee, the range of beam energies and beam currents is large between each mode of operation, all scaled to an available 50 MW maximum power per beam. The two limiting scenarios for the RF system design are at low energy (45 GeV) with high beam current (1.45 A) and the highest energy (182.5 GeV) with a radiation loss reaching 8.92 GeV per turn. In this paper, RF staging with a hybrid scheme using both 400 MHz and 800 MHz is proposed to mitigate the requirements on the two extremes. Relevant comparisons are made with respect to using only a single frequency for all modes.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOPMF036

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPMK105

PERLE - Lattice Design and Beam Dynamics Studies

4556

S.A. Bogacz, D. Douglas, F.E. Hannon, A. Hutton, F. Marhauser, R.A. Rimmer, Y. Roblin, C. Tennant
JLab, Newport News, Virginia, USA
D. Angal-Kalinin, J.W. McKenzie, B.L. Militsyn, P.H. Williams
Cockcroft Institute, Warrington, Cheshire, United Kingdom
G. Arduini, O.S. Brüning, R. Calaga, K.M. Dr. Schirm, F. Gerigk, B.J. Holzer, E. Jensen, A. Milanese, E. Montesinos, D. Pellegrini, P.A. Thonet, A. Valloni
CERN, Geneva, Switzerland
S. Bousson, D. Longuevergne, G. Olivier, G. Olry
IPN, Orsay, France
I. Chaikovska, W. Kaabi, A. Stocchi, C. Vallerand
LAL, Orsay, France
B. Hounsell, M. Klein, U.K. Klein, P. Kostka, C.P. Welsch
The University of Liverpool, Liverpool, United Kingdom
E.B. Levichev, Yu.A. Pupkov
BINP SB RAS, Novosibirsk, Russia

Funding: Work has been authored by Jefferson Science Associates, LLC under Contract No. DE-AC05-06OR23177 with the U.S. Department of Energy.
PERLE (Powerful ERL for Experiments) is a novel ERL test facility, initially proposed to validate choices for a 60 GeV ERL foreseen in the design of the LHeC and the FCC-eh. Its main thrust is to probe high current, CW, multi-pass operation with superconducting cavities at 802 MHz (and perhaps testing other frequencies of interest). With very high virtual beam power (~ 10 MW), PERLE offers an opportunity for controllable study of every beam dynamic effect of interest in the next generation of ERL design; becoming a ‘stepping stone' between present state-of-art 1 MW ERLs and future 100 MW scale applications. PERLE design features Flexible Momentum Compaction lattice architecture for six vertically stacked return arcs and a high-current, 6 MeV, photo-injector. With only one pair of 4 cavity cryomodules, 400 MeV beam energy can be reached in 3 re-circulation passes, with beam currents in excess of 15 mA. The beam is decelerated in 3 consecutive passes back to the injection energy, transferring virtually stored energy back to the RF. This unique facility will serve as a test-bed for high current ERL technologies, as well as a user facility in low energy electron and photon physics.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPMK105

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)