IPAC2018 - List of Authors (Bodenstein, R.M.)

Paper	Title	Page
MOPML010	Challenges and Status of Tuning Simulations for CLIC Traditional Beam Delivery System	412
	R.M. Bodenstein, P. Burrows JAI, Oxford, United Kingdom E. Marín CERN, Geneva, Switzerland
	The beam delivery system (BDS) for the 3 TeV version of the Compact Linear Collider (CLIC) has two main design types. One type is referred to as the local scheme, as it is approximately one kilometer shorter and corrects the chromaticity in both planes. The other type is referred to as the traditional scheme, and separates the chromaticity correction of each plane into different areas. The expectation early in the studies was that the traditional scheme would be easier to tune. This work will address the problems experienced in tuning simulations for the traditional BDS and describe the current state of these simulations.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOPML010
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUZGBD5	Performance of Nanometre-Level Resolution Cavity Beam Position Monitors at ATF2	1212
	T. Bromwich, D.R. Bett, N. Blaskovic Kraljevic, R.M. Bodenstein, P. Burrows, G.B. Christian, C. Perry, R.L. Ramjiawan JAI, Oxford, United Kingdom S. Araki, A. Aryshev, T. Tauchi, N. Terunuma KEK, Ibaraki, Japan P. Bambade, S. Wallon LAL, Orsay, France S.W. Jang Korea University Sejong Campus, Sejong, Republic of Korea
	A system of three low-Q cavity beam position monitors (BPMs), installed in the interaction point (IP) region of the Accelerator Test Facility (ATF2) at KEK, has been designed and optimised for nanometre-level beam position resolution. The BPMs are used to provide an input to a low-latency, intra-train beam position feedback system deployed in single-pass, multi-bunch mode with the aim of demonstrating intra-train beam stabilisation on electron bunches of charge ~1 nC separated in time by 280 ns. In 2016 the BPM resolution was demonstrated to be below 50 nm using the raw measured vertical positions at the three BPMs. New results will be presented utilising integrated sampling of the raw waveforms, improved BPM alignment and modified cavities to demonstrate a vertical position resolution on the order of 20 nm.
	Slides TUZGBD5 [8.557 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD5
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAL025	Development of a Low-Latency, High-Precision, Beam-Based Feedback System Based on Cavity BPMs at the KEK ATF2	2212
SUSPL058	use link to see paper's listing under its alternate paper code
	R.L. Ramjiawan, D.R. Bett, N. Blaskovic Kraljevic, R.M. Bodenstein, T. Bromwich, P. Burrows, G.B. Christian, C. Perry JAI, Oxford, United Kingdom
	A low-latency, intra-train feedback system employing cavity beam position monitors (BPMs) has been developed and tested at the Accelerator Test Facility (ATF2) at KEK. The feedback system can be operated with either position information from a single BPM to provide local beam stabilisation, or by using position information from two BPMs to stabilise the beam at an intermediate location. The correction is implemented using a stripline kicker and a custom power amplifier, with the feedback calculations being performed on a digital board built around a Field Programmable Gate Array (FPGA). The addition of indium sealing to the BPMs to increase the cavities' Q-values has led to improvements to the BPM system resolution, with current measurements of the resolution of order 20 nm. The feedback performance was tested with beam trains of two bunches, separated by 280 ns and with a charge of ~1 nC. For single- (two-)BPM feedback, stabilisation of the beam has been demonstrated to below 50 nm (41 nm). Ongoing work to improve the feedback performance further will be discussed.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAL025
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Challenges and Status of Tuning Simulations for CLIC Traditional Beam Delivery System

412

R.M. Bodenstein, P. Burrows
JAI, Oxford, United Kingdom
E. Marín
CERN, Geneva, Switzerland

The beam delivery system (BDS) for the 3 TeV version of the Compact Linear Collider (CLIC) has two main design types. One type is referred to as the local scheme, as it is approximately one kilometer shorter and corrects the chromaticity in both planes. The other type is referred to as the traditional scheme, and separates the chromaticity correction of each plane into different areas. The expectation early in the studies was that the traditional scheme would be easier to tune. This work will address the problems experienced in tuning simulations for the traditional BDS and describe the current state of these simulations.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-MOPML010

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUZGBD5

Performance of Nanometre-Level Resolution Cavity Beam Position Monitors at ATF2

1212

T. Bromwich, D.R. Bett, N. Blaskovic Kraljevic, R.M. Bodenstein, P. Burrows, G.B. Christian, C. Perry, R.L. Ramjiawan
JAI, Oxford, United Kingdom
S. Araki, A. Aryshev, T. Tauchi, N. Terunuma
KEK, Ibaraki, Japan
P. Bambade, S. Wallon
LAL, Orsay, France
S.W. Jang
Korea University Sejong Campus, Sejong, Republic of Korea

A system of three low-Q cavity beam position monitors (BPMs), installed in the interaction point (IP) region of the Accelerator Test Facility (ATF2) at KEK, has been designed and optimised for nanometre-level beam position resolution. The BPMs are used to provide an input to a low-latency, intra-train beam position feedback system deployed in single-pass, multi-bunch mode with the aim of demonstrating intra-train beam stabilisation on electron bunches of charge ~1 nC separated in time by 280 ns. In 2016 the BPM resolution was demonstrated to be below 50 nm using the raw measured vertical positions at the three BPMs. New results will be presented utilising integrated sampling of the raw waveforms, improved BPM alignment and modified cavities to demonstrate a vertical position resolution on the order of 20 nm.

Slides TUZGBD5 [8.557 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD5

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAL025

Development of a Low-Latency, High-Precision, Beam-Based Feedback System Based on Cavity BPMs at the KEK ATF2

2212

SUSPL058

use link to see paper's listing under its alternate paper code

R.L. Ramjiawan, D.R. Bett, N. Blaskovic Kraljevic, R.M. Bodenstein, T. Bromwich, P. Burrows, G.B. Christian, C. Perry
JAI, Oxford, United Kingdom

A low-latency, intra-train feedback system employing cavity beam position monitors (BPMs) has been developed and tested at the Accelerator Test Facility (ATF2) at KEK. The feedback system can be operated with either position information from a single BPM to provide local beam stabilisation, or by using position information from two BPMs to stabilise the beam at an intermediate location. The correction is implemented using a stripline kicker and a custom power amplifier, with the feedback calculations being performed on a digital board built around a Field Programmable Gate Array (FPGA). The addition of indium sealing to the BPMs to increase the cavities' Q-values has led to improvements to the BPM system resolution, with current measurements of the resolution of order 20 nm. The feedback performance was tested with beam trains of two bunches, separated by 280 ns and with a charge of ~1 nC. For single- (two-)BPM feedback, stabilisation of the beam has been demonstrated to below 50 nm (41 nm). Ongoing work to improve the feedback performance further will be discussed.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAL025

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)