SRF2021 - List of Authors (Khabiboulline, T.N.)

Paper	Title	Page
SUPTEV013	Validation of the 650 MHz SRF Cavity Tuner for PIP-II at 2 K	151
	C. Contreras-Martinez FRIB, East Lansing, Michigan, USA S.K. Chandrasekaran, S. Cheban, G.V. Eremeev, F. Furuta, T.N. Khabiboulline, Y.M. Pischalnikov, O.V. Prokofiev, A.I. Sukhanov, J.C. Yun Fermilab, Batavia, Illinois, USA
	The PIP-II linac will include thirty-six β=0.61 and twenty-four β=0.92 650 MHz 5 cell elliptical SRF cavities. Each cavity will be equipped with a tuning system consisting of a double lever slow tuner for coarse frequency tuning and a piezoelectric actuator for fine frequency tuning. One dressed cavity equipped with an SRF tuner has been tested in the horizontal test stand at Fermilab. Results of testing the cavity-tuner system will be presented.
	Poster SUPTEV013 [0.835 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-SRF2021-SUPTEV013
About •	Received ※ 22 June 2021 — Revised ※ 13 August 2021 — Accepted ※ 26 February 2022 — Issue date ※ 02 May 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

SUPTEV014	SRF Cavity Tuners for 3.9 GHz Cryomodules for LCLS-II Project	155
	C. Contreras-Martinez FRIB, East Lansing, Michigan, USA T.T. Arkan, T.N. Khabiboulline, Y.M. Pischalnikov, G.V. Romanov, R.P. Stanek, J.C. Yun Fermilab, Batavia, Illinois, USA
	Fermilab conducted testing of three 3.9 GHz cryomodules for the LCLS-II project that will operate in continuous wave mode. A fast/fine tuning component was added to the LCLS-II 3.9 GHz tuner design due to the cavity bandwidth of 130 Hz which consists of two encapsulated piezos. Several cavities faced problems with fast-tuner operations after cooldown to 2 K and tuning the cavities to 3.9 GHz in cryomodule 2. All the piezo actuators were in working conditions but the slow tuner ranges required to stretch some of the cavities to the operational 3.9 GHz frequency were too small to deliver the required preload on the piezos. This behavior can be attributed to several factors: setting the initial warm cavity frequency during production too high, pressure tests of the warm cryomodule could have changed cavity frequency; and the small bending and twisting of the cavity-tuner system during the cooldown and warmup of the cavities. A decision was made to inelastically retune the warm cavities to decrease the unrestrained frequency by 200-300 kHz, this was done via the slow tuner. The results for this retuning method of three 3.9GHz cryomodules will be discussed.
	Poster SUPTEV014 [0.720 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-SRF2021-SUPTEV014
About •	Received ※ 22 June 2021 — Accepted ※ 23 January 2022 — Issue date ※ 09 April 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPTEV002	Extended Range SRF Cavity Tuner for LCLS II HE Project	203
	Y.M. Pischalnikov, T.T. Arkan, C.J. Grimm, B.D. Hartsell, J.A. Kaluzny, T.N. Khabiboulline, Y.M. Orlov, J.C. Yun Fermilab, Batavia, Illinois, USA C. Contreras-Martinez FRIB, East Lansing, Michigan, USA
	Funding: This manuscript has been authorized by Fermi Research Alliance LLC under Contract N. DE-AC02-07CH11359 with U.S. Department of Energy. The off-frequency detune method is being considered to be applied in the LCLS-II-HE superconducting linac to produce multi-energy electron beams for supporting multiple undulator lines simultaneously. To deliver off-frequency operation (OFO) requirements for SRF cavity tuner must be changed. Tuner design modifications and results of the testing eight cavity/tuner system, deployed in verification cryomodule (vCM), will be presented.
	Poster MOPTEV002 [0.710 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-SRF2021-MOPTEV002
About •	Received ※ 22 June 2021 — Revised ※ 16 July 2021 — Accepted ※ 19 August 2021 — Issue date ※ 23 September 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPCAV005	Toward Qualifications of HB and LB 650 MHz Cavities for the Prototype Cryomodules for the PIP-II Project	448
	M. Martinello, D.J. Bice, C. Boffo, S.K. Chandrasekaran, G.V. Eremeev, F. Furuta, T.N. Khabiboulline, K.E. McGee, A.V. Netepenko, J.P. Ozelis, A.I. Sukhanov, G. Wu Fermilab, Batavia, Illinois, USA M. Bagre, V. Jain, A. Puntambekar, S. Raghvendra, P. Shrivastava RRCAT, Indore (M.P.), India M. Bertucci, A. Bosotti, C. Pagani, R. Paparella INFN/LASA, Segrate (MI), Italy P. Bhattacharyya, S. Ghosh, S. Ghosh, A. Mandal, S. Seth, S. Som VECC, Kolkata, India M.P. Kelly, T. Reid ANL, Lemont, Illinois, USA S.H. Kim, K.E. McGee, P.N. Ostroumov FRIB, East Lansing, Michigan, USA K.K. Mistri, P.N. Prakash IUAC, New Delhi, India
	High-beta (HB) and low-beta (LB) 650 MHz cryomodules are key components of the Proton Improvement Plan II (PIP-II) project. In this contribution we present the results of several 5-cell HB650 cavities that have been processed and tested with the purpose of qualifying them for the prototype cryomodule assembly, which will take place later this year. We also present the first results obtained in LB650 single-cell cavities process optimization. Taking advantage of their very similar geometry, we are also analyzing the effect of different surface treatments in FRIB’s 5-cell medium-beta 644MHz cavities. Cavities processed with N-doping and mid-T baking showed very promising results in term of both Q-factors and accelerating gradient for these low-beta structures.
DOI •	reference for this paper ※ doi:10.18429/JACoW-SRF2021-TUPCAV005
About •	Received ※ 01 July 2021 — Accepted ※ 02 November 2021 — Issue date ※ 16 May 2022
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPCAV013	STC Qualification Tests of PIP-II HB650 Cavities	465
	A.I. Sukhanov, S.K. Chandrasekaran, G.V. Eremeev, F. Furuta, S. Kazakov, T.N. Khabiboulline, T.H. Nicol, Y.M. Pischalnikov, O.V. Prokofiev, V. Roger, G. Wu, V.P. Yakovlev, J.C. Yun Fermilab, Batavia, Illinois, USA C. Contreras-Martinez FRIB, East Lansing, Michigan, USA
	Design of the high beta 650 MHz prototype cryomodule for PIP-II is currently undergoing at Fermilab. The cryomodule includes six 5-cell elliptical SRF cavities with accelerating voltage up to 20 MV and low heat dissipation (Q₀ > 3.3 · 10^zEhNZeHn). Characterization of performance of fully integrated jacketed cavities with high power coupler and tuner is crucial for the project. Such a characterization of jacketed cavity requires a horizontal test cryostat. The Fermilab Spoke Test Cryostat (STC) has been upgraded to accommodate testing of 650 MHz cavities. Commissioning of upgraded STC has been reported at SRF’19 conference. In this paper we present results of testing of the prototype HB650 cavity in upgraded STC facility. We characterize cavity performance and qualify it for the prototype HB650 cryomodule assembly.
DOI •	reference for this paper ※ doi:10.18429/JACoW-SRF2021-TUPCAV013
About •	Received ※ 21 June 2021 — Accepted ※ 21 August 2021 — Issue date ※ 04 October 2021
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Validation of the 650 MHz SRF Cavity Tuner for PIP-II at 2 K

151

C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA
S.K. Chandrasekaran, S. Cheban, G.V. Eremeev, F. Furuta, T.N. Khabiboulline, Y.M. Pischalnikov, O.V. Prokofiev, A.I. Sukhanov, J.C. Yun
Fermilab, Batavia, Illinois, USA

The PIP-II linac will include thirty-six β=0.61 and twenty-four β=0.92 650 MHz 5 cell elliptical SRF cavities. Each cavity will be equipped with a tuning system consisting of a double lever slow tuner for coarse frequency tuning and a piezoelectric actuator for fine frequency tuning. One dressed cavity equipped with an SRF tuner has been tested in the horizontal test stand at Fermilab. Results of testing the cavity-tuner system will be presented.

Poster SUPTEV013 [0.835 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-SRF2021-SUPTEV013

About •

Received ※ 22 June 2021 — Revised ※ 13 August 2021 — Accepted ※ 26 February 2022 — Issue date ※ 02 May 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

SUPTEV014

SRF Cavity Tuners for 3.9 GHz Cryomodules for LCLS-II Project

155

C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA
T.T. Arkan, T.N. Khabiboulline, Y.M. Pischalnikov, G.V. Romanov, R.P. Stanek, J.C. Yun
Fermilab, Batavia, Illinois, USA

Fermilab conducted testing of three 3.9 GHz cryomodules for the LCLS-II project that will operate in continuous wave mode. A fast/fine tuning component was added to the LCLS-II 3.9 GHz tuner design due to the cavity bandwidth of 130 Hz which consists of two encapsulated piezos. Several cavities faced problems with fast-tuner operations after cooldown to 2 K and tuning the cavities to 3.9 GHz in cryomodule 2. All the piezo actuators were in working conditions but the slow tuner ranges required to stretch some of the cavities to the operational 3.9 GHz frequency were too small to deliver the required preload on the piezos. This behavior can be attributed to several factors: setting the initial warm cavity frequency during production too high, pressure tests of the warm cryomodule could have changed cavity frequency; and the small bending and twisting of the cavity-tuner system during the cooldown and warmup of the cavities. A decision was made to inelastically retune the warm cavities to decrease the unrestrained frequency by 200-300 kHz, this was done via the slow tuner. The results for this retuning method of three 3.9GHz cryomodules will be discussed.

Poster SUPTEV014 [0.720 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-SRF2021-SUPTEV014

About •

Received ※ 22 June 2021 — Accepted ※ 23 January 2022 — Issue date ※ 09 April 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPTEV002

Extended Range SRF Cavity Tuner for LCLS II HE Project

203

Y.M. Pischalnikov, T.T. Arkan, C.J. Grimm, B.D. Hartsell, J.A. Kaluzny, T.N. Khabiboulline, Y.M. Orlov, J.C. Yun
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA

Funding: This manuscript has been authorized by Fermi Research Alliance LLC under Contract N. DE-AC02-07CH11359 with U.S. Department of Energy.
The off-frequency detune method is being considered to be applied in the LCLS-II-HE superconducting linac to produce multi-energy electron beams for supporting multiple undulator lines simultaneously. To deliver off-frequency operation (OFO) requirements for SRF cavity tuner must be changed. Tuner design modifications and results of the testing eight cavity/tuner system, deployed in verification cryomodule (vCM), will be presented.

Poster MOPTEV002 [0.710 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-SRF2021-MOPTEV002

About •

Received ※ 22 June 2021 — Revised ※ 16 July 2021 — Accepted ※ 19 August 2021 — Issue date ※ 23 September 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPCAV005

Toward Qualifications of HB and LB 650 MHz Cavities for the Prototype Cryomodules for the PIP-II Project

448

M. Martinello, D.J. Bice, C. Boffo, S.K. Chandrasekaran, G.V. Eremeev, F. Furuta, T.N. Khabiboulline, K.E. McGee, A.V. Netepenko, J.P. Ozelis, A.I. Sukhanov, G. Wu
Fermilab, Batavia, Illinois, USA
M. Bagre, V. Jain, A. Puntambekar, S. Raghvendra, P. Shrivastava
RRCAT, Indore (M.P.), India
M. Bertucci, A. Bosotti, C. Pagani, R. Paparella
INFN/LASA, Segrate (MI), Italy
P. Bhattacharyya, S. Ghosh, S. Ghosh, A. Mandal, S. Seth, S. Som
VECC, Kolkata, India
M.P. Kelly, T. Reid
ANL, Lemont, Illinois, USA
S.H. Kim, K.E. McGee, P.N. Ostroumov
FRIB, East Lansing, Michigan, USA
K.K. Mistri, P.N. Prakash
IUAC, New Delhi, India

High-beta (HB) and low-beta (LB) 650 MHz cryomodules are key components of the Proton Improvement Plan II (PIP-II) project. In this contribution we present the results of several 5-cell HB650 cavities that have been processed and tested with the purpose of qualifying them for the prototype cryomodule assembly, which will take place later this year. We also present the first results obtained in LB650 single-cell cavities process optimization. Taking advantage of their very similar geometry, we are also analyzing the effect of different surface treatments in FRIB’s 5-cell medium-beta 644MHz cavities. Cavities processed with N-doping and mid-T baking showed very promising results in term of both Q-factors and accelerating gradient for these low-beta structures.

DOI •

reference for this paper ※ doi:10.18429/JACoW-SRF2021-TUPCAV005

About •

Received ※ 01 July 2021 — Accepted ※ 02 November 2021 — Issue date ※ 16 May 2022

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPCAV013

STC Qualification Tests of PIP-II HB650 Cavities

465

A.I. Sukhanov, S.K. Chandrasekaran, G.V. Eremeev, F. Furuta, S. Kazakov, T.N. Khabiboulline, T.H. Nicol, Y.M. Pischalnikov, O.V. Prokofiev, V. Roger, G. Wu, V.P. Yakovlev, J.C. Yun
Fermilab, Batavia, Illinois, USA
C. Contreras-Martinez
FRIB, East Lansing, Michigan, USA

Design of the high beta 650 MHz prototype cryomodule for PIP-II is currently undergoing at Fermilab. The cryomodule includes six 5-cell elliptical SRF cavities with accelerating voltage up to 20 MV and low heat dissipation (Q₀ > 3.3 · 10^zEhNZeHn). Characterization of performance of fully integrated jacketed cavities with high power coupler and tuner is crucial for the project. Such a characterization of jacketed cavity requires a horizontal test cryostat. The Fermilab Spoke Test Cryostat (STC) has been upgraded to accommodate testing of 650 MHz cavities. Commissioning of upgraded STC has been reported at SRF’19 conference. In this paper we present results of testing of the prototype HB650 cavity in upgraded STC facility. We characterize cavity performance and qualify it for the prototype HB650 cryomodule assembly.

DOI •

reference for this paper ※ doi:10.18429/JACoW-SRF2021-TUPCAV013

About •

Received ※ 21 June 2021 — Accepted ※ 21 August 2021 — Issue date ※ 04 October 2021

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)