| Paper |
Title |
Page |
| TPAP003 |
Exploring a Nonlinear Collimation System for the LHC
|
877 |
| |
- J. Resta, A. Faus-Golfe
IFIC, Valencia
- R.W. Assmann, S. Redaelli, G. Robert-Demolaize, D. Schulte, F. Zimmermann
CERN, Geneva
|
|
| |
We explore the adaptation of a nonlinear collimation system, as previously considered for linear colliders, to LHC betatron cleaning. A possible nonlinear system for LHC consists of a horizontal and vertical primary collimator located in between a pair of skew sextupoles. We discuss the modified LHC optics, the need for and optimum placement of secondary absorbers, and the simulated cleaning efficiency.
|
|
| TPAP004 |
Mechanical Design for Robustness of the LHC Collimators
|
913 |
| |
- A. Bertarelli, O. Aberle, R.W. Assmann, S. Calatroni, A. Dallocchio, T. Kurtyka, M. Mayer, R. Perret, S. Redaelli, G. Robert-Demolaize
CERN, Geneva
|
|
| |
The functional specification of the LHC Collimators requires, for the start-up of the machine and the initial luminosity runs (Phase 1), a collimation system with maximum robustness against abnormal beam operating conditions. The most severe cases to be considered in the mechanical design are the asynchronous beam dump at 7 TeV and the 450 GeV injection error. To ensure that the collimator jaws survive such accident scenarios, low-Z materials were chosen, driving the design towards Graphite or Carbon/Carbon composites. Furthermore, in-depth thermo-mechanical simulations, both static and dynamic, were necessary.This paper presents the results of the numerical analyses performed for the 450 GeV accident case, along with the experimental results of the tests conducted on a collimator prototype in Cern TT40 transfer line, impacted by a 450 GeV beam of 3.1·1013 protons, with impact parameters from 1 to 5 mm.
|
|
| TPAP007 |
LHC Collimation: Design and Results from Prototyping and Beam Tests
|
1078 |
| |
- R.W. Assmann, O. Aberle, G. Arduini, A. Bertarelli, H.-H. Braun, M. Brugger, H. Burkhardt, S. Calatroni, F. Caspers, E. Chiaveri, A. Dallocchio, B. Dehning, A. Ferrari, M. Gasior, A. Grudiev, E.B. Holzer, J.-B. Jeanneret, J.M. Jimenez, Y. Kadi, R. Losito, M. Magistris, A.M. Masi, M. Mayer, E. Métral, R. Perret, C. Rathjen, S. Redaelli, G. Robert-Demolaize, S. Roesler, M. Santana-Leitner, D. Schulte, P. Sievers, E. Tsoulou, H. Vincke, V. Vlachoudis, J. Wenninger
CERN, Geneva
- I. Baishev, I.L. Kurochkin
IHEP Protvino, Protvino, Moscow Region
- G. Spiezia
Naples University Federico II, Science and Technology Pole, Napoli
|
|
| |
The problem of collimation and beam cleaning concerns one of the most challenging aspects of the LHC project. A collimation system must be designed, built, installed and commissioned with parameters that extend the present state-of-the-art by 2-3 orders of magnitude. Problems include robustness, cleaning efficiency, impedance and operational aspects. A strong design effort has been performed at CERN over the last two years. The system design has now been finalized for the two cleaning insertions. The adopted phased approach is described and the expected collimation performance is discussed. In parallel robust and precisely controllable collimators have been designed. Several LHC prototype collimators have been built and tested with the highest beam intensities that are presently available at CERN. The successful beam tests are presented, including beam-based setup procedures, a 2 MJ robustness test and measurements of the collimator-induced impedance. Finally, an outlook is presented on the challenges that are ahead in the coming years.
|
|
| TPAP008 |
Measurements of the LHC Collimator Impedance with Beam in the SPS
|
1132 |
| |
- H. Burkhardt, G. Arduini, R.W. Assmann, F. Caspers, M. Gasior, A. Grudiev, O.R. Jones, T. Kroyer, E. Métral, S. Redaelli, G. Robert-Demolaize, F. Roncarolo, D. Schulte, R.J. Steinhagen, J. Wenninger, F. Zimmermann
CERN, Geneva
|
|
| |
The transverse impedance of the LHC collimators will likely dominate the overall transverse impedance in the LHC at high energies and potentially limit the maximum intensity. A prototype collimator was recently tested in the SPS. Small, but significant tune shifts depending on the collimator position have been observed using different independent high resolution tune measurement methods. In addition trapped modes predicted from numerical simulation at the ends of the collimator jaws have been identified by bench measurement techniques as well as with the beam. We present a description of the measurements and an analysis of the results.
|
|
| FPAT081 |
A New Version of SixTrack with Collimation and Aperture Interface
|
4084 |
| |
- G. Robert-Demolaize, R.W. Assmann, S. Redaelli, F. Schmidt
CERN, Geneva
|
|
| |
Simulations of collimation and beam cleaning were so far often performed with simplified computer models. However, the increase in available CPU power has opened the possibility for far more realistic simulations. For large accelerators like LHC it is now possible to track millions of particles, element by element over hundreds of turns. The well established SixTrack code treats the full six-dimensional phase space and considers the non-linear magnet components up to very high order. This code is being used for all LHC tracking simulations and has well developed linear and non-linear error models. SixTrack was extended for tracking of large ensembles of halo particles, taking into account halo interaction with arbitrarily placed collimators. An interface to a program for aperture analysis allows obtaining beam loss maps in the machine aperture. A standardized and portable SixTrack version is now available, providing all functionality of the old SixTrack, as well as the newly added support for halo tracking, collimation and aperture loss maps.
|
|