Paper |
Title |
Page |
THOAM01 |
Development and Qualification of Micrometre Resolution Motorized Actuators for the High Luminosity Large Hadron Collider Full Remote Alignment System |
243 |
|
- M.N. Noir, P.B. Biedrawa, S.F. Fargier, J.W. Jasonek, M. Sosin
CERN, Meyrin, Switzerland
- P.B. Biedrawa, J.W. Jasonek
AGH University of Science and Technology, Kraków, Poland
|
|
|
In the framework of the High-Luminosity Large Hadron Collider project at CERN, a Full Remote Alignment System (FRAS) is under development, integrating a range of solutions for the remote positioning of accelerator components. An important component of FRAS is the motorized actuator allowing the remote adjustment of accelerator components with a micrometer resolution. These actuators need to fulfill multiple requirements to comply with safety rules, and be highly reliable and maintenance free as thus are located in a harsh environment. The integration of the safety functions required for the FRAS was crucial, with the motorized actuators able to provide an absolute position monitoring of the available stroke, integrating electrical end-stops and having an embedded mechanical stop as a hardware safety layer. In addition, the design has been elaborated to allow a rapid, in-situ readjustment of the nominal stroke in order to cope with potential readjustment requirements, following long-term drifts caused by ground motion. This paper describes the design approach, prototyping and qualification of these motorized actuators.
|
|
|
Slides THOAM01 [8.636 MB]
|
|
DOI • |
reference for this paper
※ doi:10.18429/JACoW-MEDSI2023-THOAM01
|
|
About • |
Received ※ 26 October 2023 — Revised ※ 03 November 2023 — Accepted ※ 07 November 2023 — Issued ※ 08 May 2024 |
Cite • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
THPPP026 |
Motorized Universal Adjustment Platform for Micrometric Adjustment of Accelerator Components |
316 |
|
- M.N. Noir, D.B. Baillard, P.B. Biedrawa, L. Gentini, J.W. Jasonek, F.-X. Nuiry, V. Rude, R. Seidenbinder, M. Sosin, K. Widuch
CERN, Meyrin, Switzerland
- P.B. Biedrawa, J.W. Jasonek
AGH University of Science and Technology, Kraków, Poland
- A. Gothe
Aarhus University, Aarhus, Denmark
|
|
|
In order to optimize alignment activities in a highly radioactive environment, the Geodetic Metrology Group at CERN has developed a standardized featuring 6 degree of freedom (DoF) Universal Adjustment Platform (UAP). After a first prototyping phase in 2021 with a manual UAP, the design has been consolidated and is now compatible with the installation of motorized actuators to form a remotely adjustable 5-6 DoF platform able to perform positioning with micrometre resolution. This paper presents the UAP and related motorized actuator development, elaborated in the frame of the High-Luminosity Large Hadron Collider project. The mechanical integration approach, design solutions, and test results are discussed.
|
|
|
Poster THPPP026 [1.494 MB]
|
|
DOI • |
reference for this paper
※ doi:10.18429/JACoW-MEDSI2023-THPPP026
|
|
About • |
Received ※ 26 October 2023 — Revised ※ 03 November 2023 — Accepted ※ 07 November 2023 — Issued ※ 28 November 2023 |
Cite • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|