LINAC2014 - List of Authors (Boorman, G.E.)

Paper	Title	Page
MOPP129	Status of the FETS Project	361
	A.P. Letchford, M.A. Clarke-Gayther, D.C. Faircloth, S.R. Lawrie STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom S.M.H. Alsari, M. Aslaninejad, J.K. Pozimski, P. Savage Imperial College of Science and Technology, Department of Physics, London, United Kingdom J.J. Back University of Warwick, Coventry, United Kingdom G.E. Boorman, A. Bosco, S.M. Gibson Royal Holloway, University of London, Surrey, United Kingdom R.T.P. D'Arcy, S. Jolly UCL, London, United Kingdom M. Dudman, J.K. Pozimski STFC/RAL, Chilton, Didcot, Oxon, United Kingdom D.C. Plostinar STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
	The Front End Test Stand (FETS) under construction at RAL is a demonstrator for front end systems of a future high power proton linac. Possible applications include a linac upgrade for the ISIS spallation neutron source, new future neutron sources, accelerator driven sub-critical systems, high energy physics proton drivers etc. Designed to deliver a 60mA H-minus beam at 3MeV with a 10% duty factor, FETS consists of a high brightness ion source, magnetic low energy beam transport (LEBT), 4-vane 324MHz radio frequency quadrupole, medium energy beam transport (MEBT) containing a high speed beam chopper and non-destructive laser diagnostics. This paper describes the current status of the project and future plans.

TUPP035	Transverse Profile and Emittance Measurements With a Laser Stripping System During the CERN LINAC4 Commissioning at 3 and 12 MeV	506
	F. Roncarolo, E. Bravin, T. Hofmann, U. Raich, F. Zocca CERN, Geneva, Switzerland G.E. Boorman, A. Bosco, S.M. Gibson, K.O. Kruchinin Royal Holloway, University of London, Surrey, United Kingdom C. Gabor STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom J.K. Pozimski Imperial College of Science and Technology, Department of Physics, London, United Kingdom
	The CERN LINAC4 beam commissioning at 3 and 12 MeV was completed in 2014. A novel system for measuring the transverse beam profile and emittance, based on low power laser stripping and H⁰ detection using a diamond detector, was successfully tested at these two energies. The measurement results agree with the operational slit-grid method within a few percent in terms of both transverse profile and emittance. After describing the general system setup, this remarkable achievement is discussed in detail together with the present limitations, which will be addressed in order to design a laser based emittance monitor for the LINAC4 top energy of 160 MeV.

Paper

Title

Page

Status of the FETS Project

361

A.P. Letchford, M.A. Clarke-Gayther, D.C. Faircloth, S.R. Lawrie
STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom
S.M.H. Alsari, M. Aslaninejad, J.K. Pozimski, P. Savage
Imperial College of Science and Technology, Department of Physics, London, United Kingdom
J.J. Back
University of Warwick, Coventry, United Kingdom
G.E. Boorman, A. Bosco, S.M. Gibson
Royal Holloway, University of London, Surrey, United Kingdom
R.T.P. D'Arcy, S. Jolly
UCL, London, United Kingdom
M. Dudman, J.K. Pozimski
STFC/RAL, Chilton, Didcot, Oxon, United Kingdom
D.C. Plostinar
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom

The Front End Test Stand (FETS) under construction at RAL is a demonstrator for front end systems of a future high power proton linac. Possible applications include a linac upgrade for the ISIS spallation neutron source, new future neutron sources, accelerator driven sub-critical systems, high energy physics proton drivers etc. Designed to deliver a 60mA H-minus beam at 3MeV with a 10% duty factor, FETS consists of a high brightness ion source, magnetic low energy beam transport (LEBT), 4-vane 324MHz radio frequency quadrupole, medium energy beam transport (MEBT) containing a high speed beam chopper and non-destructive laser diagnostics. This paper describes the current status of the project and future plans.

TUPP035

Transverse Profile and Emittance Measurements With a Laser Stripping System During the CERN LINAC4 Commissioning at 3 and 12 MeV

506

F. Roncarolo, E. Bravin, T. Hofmann, U. Raich, F. Zocca
CERN, Geneva, Switzerland
G.E. Boorman, A. Bosco, S.M. Gibson, K.O. Kruchinin
Royal Holloway, University of London, Surrey, United Kingdom
C. Gabor
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
J.K. Pozimski
Imperial College of Science and Technology, Department of Physics, London, United Kingdom

The CERN LINAC4 beam commissioning at 3 and 12 MeV was completed in 2014. A novel system for measuring the transverse beam profile and emittance, based on low power laser stripping and H⁰ detection using a diamond detector, was successfully tested at these two energies. The measurement results agree with the operational slit-grid method within a few percent in terms of both transverse profile and emittance. After describing the general system setup, this remarkable achievement is discussed in detail together with the present limitations, which will be addressed in order to design a laser based emittance monitor for the LINAC4 top energy of 160 MeV.