LINAC2012 - List of Authors (Klump, B.)

Paper	Title	Page
SUPB017	Tuning Studies on 4-rod-RFQs	44
	J.S. Schmidt, B. Klump, B. Koubek, A. Schempp IAP, Frankfurt am Main, Germany
	A NI LabVIEW based Tuning Software has been devel- oped to structure the tuning process of 4-rod Radio Fre- quency Quadrupole s (RFQs). Its results are compared to measurement data of 4-rod RFQs in different frequency ranges. For the optimization of RFQ design parameters, a certain voltage distribution along the electrodes of an RFQ is assumed. Therefore an accurate tuning of the voltage distribution is very important for the beam dynamic prop- erties of an RFQ. A variation can lead to particle losses and reduced beam quality especially at higher frequencies. Our electrode design usually implies a constant longitudi- nal voltage distribution. For its adjustment tuning plates are used between the stems of the 4-rod-RFQ. These pre- dictions are based, in contrast to other simulations, on mea- surements to define the characteristics of the RFQ as it was build - not depending on assumptions of the design. This will lead to a totally new structured process of tuning 4- rod-RFQs in a broad range of frequencies by using the pre- dictions of a software. The results of these studies are pre- sented in this paper.

THPB049	Tuning Studies on 4-Rod-RFQs	963
	J.S. Schmidt, B. Klump, B. Koubek, A. Schempp IAP, Frankfurt am Main, Germany
	A NI LabVIEW based Tuning Software has been devel- oped to structure the tuning process of 4-rod Radio Fre- quency Quadrupole s (RFQs). Its results are compared to measurement data of 4-rod RFQs in different frequency ranges. For the optimization of RFQ design parameters, a certain voltage distribution along the electrodes of an RFQ is assumed. Therefore an accurate tuning of the voltage distribution is very important for the beam dynamic prop- erties of an RFQ. A variation can lead to particle losses and reduced beam quality especially at higher frequencies. Our electrode design usually implies a constant longitudi- nal voltage distribution. For its adjustment tuning plates are used between the stems of the 4-rod-RFQ. These pre- dictions are based, in contrast to other simulations, on mea- surements to define the characteristics of the RFQ as it was build - not depending on assumptions of the design. This will lead to a totally new structured process of tuning 4- rod-RFQs in a broad range of frequencies by using the pre- dictions of a software. The results of these studies are pre- sented in this paper.

Paper

Title

Page

Tuning Studies on 4-rod-RFQs

44

J.S. Schmidt, B. Klump, B. Koubek, A. Schempp
IAP, Frankfurt am Main, Germany

A NI LabVIEW based Tuning Software has been devel- oped to structure the tuning process of 4-rod Radio Fre- quency Quadrupole s (RFQs). Its results are compared to measurement data of 4-rod RFQs in different frequency ranges. For the optimization of RFQ design parameters, a certain voltage distribution along the electrodes of an RFQ is assumed. Therefore an accurate tuning of the voltage distribution is very important for the beam dynamic prop- erties of an RFQ. A variation can lead to particle losses and reduced beam quality especially at higher frequencies. Our electrode design usually implies a constant longitudi- nal voltage distribution. For its adjustment tuning plates are used between the stems of the 4-rod-RFQ. These pre- dictions are based, in contrast to other simulations, on mea- surements to define the characteristics of the RFQ as it was build - not depending on assumptions of the design. This will lead to a totally new structured process of tuning 4- rod-RFQs in a broad range of frequencies by using the pre- dictions of a software. The results of these studies are pre- sented in this paper.

THPB049

Tuning Studies on 4-Rod-RFQs

963

J.S. Schmidt, B. Klump, B. Koubek, A. Schempp
IAP, Frankfurt am Main, Germany

A NI LabVIEW based Tuning Software has been devel- oped to structure the tuning process of 4-rod Radio Fre- quency Quadrupole s (RFQs). Its results are compared to measurement data of 4-rod RFQs in different frequency ranges. For the optimization of RFQ design parameters, a certain voltage distribution along the electrodes of an RFQ is assumed. Therefore an accurate tuning of the voltage distribution is very important for the beam dynamic prop- erties of an RFQ. A variation can lead to particle losses and reduced beam quality especially at higher frequencies. Our electrode design usually implies a constant longitudi- nal voltage distribution. For its adjustment tuning plates are used between the stems of the 4-rod-RFQ. These pre- dictions are based, in contrast to other simulations, on mea- surements to define the characteristics of the RFQ as it was build - not depending on assumptions of the design. This will lead to a totally new structured process of tuning 4- rod-RFQs in a broad range of frequencies by using the pre- dictions of a software. The results of these studies are pre- sented in this paper.