A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z    

Igarashi, Z.

Paper Title Page
TUP06 Results of the High-Power Conditioning and the First Beam Acceleration of the DTL-1 for J-PARC 300
  • F. Naito, S. Anami, J. Chiba, Y. Fukui, K. Furukawa, Z. Igarashi, K. Ikegami, M. Ikegami, E. Kadokura, N. Kamikubota, T. Kato, M. Kawamura, H. Kobayashi, C. Kubota, E. Takasaki, H. Tanaka, S. Yamaguchi, K. Yoshino
    KEK, Ibaraki
  • K. Hasegawa, Y. Kondo, A. Ueno
    JAERI, Ibaraki-ken
  • T. Itou, Y. Yamazaki
    JAERI/LINAC, Ibaraki-ken
  • T. Kobayashi
    J-PARC, Ibaraki-ken
  The first tank of the DTL for Japan Proton Accelerator Research Complex (J-PARC) was installed in the test facility at KEK. The DTL tank is 9.9 m in length and consists of the 76 cells. The resonant frequency of the tank is 324 MHz. After the installation of the tank, the high-power conditioning was carried out deliberately. Consequently the peak rf power of 1.3 MW (pulse repetition 50 Hz, pulse length 600 μs) was put into the tank stably. (The required power is about 1.1 MW for the designed accelerating field of 2.5 MV/m on the axis.) Following the conditioning, negative hydrogen beam, accelerated by the RFQ linac up to 3 MeV, was injected to the DTL and accelerated up to its design value of 19.7 MeV. The peak current of 30 mA was achieved with almost 100% transmission. In this paper, the conditioning history of the DTL and the result of the first beam test will be described.  
TUP70 Systematic Calibration of Beam Position Monitor in the High Intensity Proton Accelerator (J-PARC) LINAC 429
  • S. Sato, K. Hasegawa, F. Hiroki, J. Kishiro, Y. Kondo, M. Tanaka, T. Tomisawa, A. Ueno, H. Yoshikawa
    JAERI, Ibaraki-ken
  • Z. Igarashi, M. Ikegami, N. Kamikubota, S. Lee, K. Nigorikawa, T. Toyama
    KEK, Ibaraki
  In J-PARC, a MW class of proton accelerator is under construction. Improperly- tuned beam would critically result in unacceptable (>0.1%) energy loss. Systematic strategy of fine calibrations of the beam position monitor (BPM) detectors, is therefore required. First, Off-beam-line calibrations of BPMs are taken, with a dedicatedly- designed bench, which has a beam-simulating electric wire carrying 324 MHz. And then discrepancies are calibrated for each BPM between reconstructed electrical center of pick-up plates and measured mechanical center, before the installation of BPM on the beam line. Secondly, after BPMs are installed on the beam line, real beam is used for systematic calibrations (Beam Based Calibration (BBC)). The discrepancies are calibrated between electromagnetic center of Q-magnets and reconstructed beam position. In KEK we have the first stage of J-Parc LINAC with Ion source, RFQ, DTL, Q- and steering-magnets, and lots of BPMs. Implementation of BBC is going with SAD-language, which can also be used for beam steering and beam trajectory simulations, e.g. TRACE-3D. In this presentation, such strategic BPM calibration system will be intensively described.  
TUP74 The Beam Diagnostics System in the J-PARC LINAC 441
  • S. Lee, Z. Igarashi, T. Toyama
    KEK, Ibaraki
  • H. Akikawa
    JAERI/LINAC, Ibaraki-ken
  • F. Hiroki, J. Kishiro, S. Sato, M. Tanaka, T. Tomisawa
    JAERI, Ibaraki-ken
  • H. Yoshikawa
    JAERI/FEL, Ibaraki-ken
  Large amount of beam monitors will be installed in J-PARC linac. Electrostatic computations are used to adjust the BPM cross-section parameters to obtain 50 Ω transmission lines. BPMs are designed to control the offset between quadrupole magnet and BPM electrical centers less than 0.1mm. We present a procedure of beam based calibration/alignment (BBC/BBA) method to confirm the displacement of linac BPMs. The fast current transformer (FCT) has response of relative bunch phase <1%. To measure the beam energy at every accelerator tank and injection point of 3 GeV RCS, phase difference of FCT pairs are used, and 10-4 order energy resolutions can be expected. The loss monitor system (BLM) is composed of scintillator and Ar-CH4/CO2 gas filled proportional counter. To prevent the activation and heat load by intense beam loss, fast time response of loss signals is required. Profile measurements can also be used to determine the beam emittance of a matched beam in a periodic focusing lattice. The thin sensing wire scanner (WS) has been designed to obtain a current density distribution of the beam. This paper describes the instruments and R&D result of beam monitors in J-PARC linac.