IPAC2021 - List of Authors (Trento, G.)

Paper	Title	Page
TUPAB354	352-MHz Solid State RF System Development at the Advanced Photon Source	2335
	D. Horan, D.J. Bromberek, N.P. DiMonte, A. Goel, T.J. Madden, A. Nassiri, G. Trento, G.J. Waldschmidt ANL, Lemont, Illinois, USA
	Development effort is underway on a 352MHz, 200kW solid state rf system intended as the base design to replace the existing klystron-based rf systems presently in use at the Advanced Photon Source (APS). A sixteen-input, 200kW final combining cavity was designed, built, and successfully tested to 29kW CW in combiner mode, and to 200kW CW in back-feed mode, where an external klystron was used to transmit power into the combining cavity. A four-port waveguide combiner was also tested in both backfeed and combiner mode to 193kW and 26kW respectively. Slow and fast interlock systems were designed and implemented to support the testing process. An EPICS and Programmable Logic Controller (PLC)-based system was developed to control, communicate with, and monitor the rf amplifiers used in the combiner-mode test, and to monitor and log system performance parameters relating to the combining cavity. Low-level rf control of the cavity in 29kW combiner-mode operation was achieved using the existing APS analog low-level rf hardware. Test data and design details are presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB354
About •	paper received ※ 18 May 2021 paper accepted ※ 31 May 2021 issue date ※ 19 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAB081	High-Power Prototype Canon Coupler for APS-U Booster Cavities	3956
	G.J. Waldschmidt, D.J. Bromberek, D. Horan, G. Trento, U. Wienands ANL, Lemont, Illinois, USA T. Harada, H. Oikawa, H. Takahashi CETD, Tochigi, Japan
	The Advanced Photon Source Upgrade (APS-U) plans to achieve a beam capture efficiency above 90% at 17 nC bunch charge into the Booster. Due to large beam loading at injection, the 352-MHz Booster cavities will be significantly detuned necessitating effective-power handling much greater than the 100kW effective power rating of the present coupler. Canon Electron Tubes & Devices Co., Ltd. (CETD) has designed and built a compact coupler for the APS-U Booster using a high-power ceramic disk window design in addition to accommodating significant space restrictions and additional diagnostics and cooling requirements. The coupler design was modified from an existing 500MHz, 800kW coupler that has been in routine operation at KEKB. The APS-U coupler has been installed and tested in the high-power 352-MHz test stand at the APS. The details of the design and testing of the prototype coupler will be reported in this paper.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-THPAB081
About •	paper received ※ 18 May 2021 paper accepted ※ 28 July 2021 issue date ※ 15 August 2021
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

352-MHz Solid State RF System Development at the Advanced Photon Source

2335

D. Horan, D.J. Bromberek, N.P. DiMonte, A. Goel, T.J. Madden, A. Nassiri, G. Trento, G.J. Waldschmidt
ANL, Lemont, Illinois, USA

Development effort is underway on a 352MHz, 200kW solid state rf system intended as the base design to replace the existing klystron-based rf systems presently in use at the Advanced Photon Source (APS). A sixteen-input, 200kW final combining cavity was designed, built, and successfully tested to 29kW CW in combiner mode, and to 200kW CW in back-feed mode, where an external klystron was used to transmit power into the combining cavity. A four-port waveguide combiner was also tested in both backfeed and combiner mode to 193kW and 26kW respectively. Slow and fast interlock systems were designed and implemented to support the testing process. An EPICS and Programmable Logic Controller (PLC)-based system was developed to control, communicate with, and monitor the rf amplifiers used in the combiner-mode test, and to monitor and log system performance parameters relating to the combining cavity. Low-level rf control of the cavity in 29kW combiner-mode operation was achieved using the existing APS analog low-level rf hardware. Test data and design details are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB354

About •

paper received ※ 18 May 2021 paper accepted ※ 31 May 2021 issue date ※ 19 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAB081

High-Power Prototype Canon Coupler for APS-U Booster Cavities

3956

G.J. Waldschmidt, D.J. Bromberek, D. Horan, G. Trento, U. Wienands
ANL, Lemont, Illinois, USA
T. Harada, H. Oikawa, H. Takahashi
CETD, Tochigi, Japan

The Advanced Photon Source Upgrade (APS-U) plans to achieve a beam capture efficiency above 90% at 17 nC bunch charge into the Booster. Due to large beam loading at injection, the 352-MHz Booster cavities will be significantly detuned necessitating effective-power handling much greater than the 100kW effective power rating of the present coupler. Canon Electron Tubes & Devices Co., Ltd. (CETD) has designed and built a compact coupler for the APS-U Booster using a high-power ceramic disk window design in addition to accommodating significant space restrictions and additional diagnostics and cooling requirements. The coupler design was modified from an existing 500MHz, 800kW coupler that has been in routine operation at KEKB. The APS-U coupler has been installed and tested in the high-power 352-MHz test stand at the APS. The details of the design and testing of the prototype coupler will be reported in this paper.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-THPAB081

About •

paper received ※ 18 May 2021 paper accepted ※ 28 July 2021 issue date ※ 15 August 2021

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)