Author: Bett, D.R.
Paper Title Page
TUPAB019 A High-Resolution, Low-Latency, Bunch-by-Bunch Feedback System for Nano-Beam Stabilization 1378
 
  • R.L. Ramjiawan, D.R. Bett, N. Blaskovic Kraljevic, T. Bromwich, P. Burrows, G.B. Christian, C. Perry
    JAI, Oxford, United Kingdom
  • D.R. Bett
    CERN, Geneva, Switzerland
  • N. Blaskovic Kraljevic
    ESS, Lund, Sweden
  • G.B. Christian
    DLS, Oxfordshire, United Kingdom
 
  A low-latency, bunch-by-bunch feedback system employing high-resolution cavity Beam Position Monitors (BPMs) has been developed and tested at the Accelerator Test Facility (ATF2) at the High Energy Accelerator Research Organization (KEK), Japan. The feedback system was designed to demonstrate nanometer-level vertical stabilization at the focal point of the ATF2 and can be operated using either a single BPM to provide local beam stabilization, or by using two BPMs to stabilize the beam at an intermediate location. The feedback correction is implemented using a stripline kicker and the feedback calculations are performed on a digital board constructed around a Field Programmable Gate Array (FPGA). The feedback performance was tested with trains of two bunches, separated by 280ns, at a charge of ~1nC, where the vertical offset of the first bunch was measured and used to calculate the correction to be applied to the second bunch. The BPMs have been demonstrated to achieve an operational resolution of ~20nm. With the application of single-BPM and two-BPM feedback, beam stabilization of below 50nm and 41nm respectively has been achieved with a latency of 232ns.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB019  
About • paper received ※ 18 May 2021       paper accepted ※ 09 June 2021       issue date ※ 14 August 2021  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPAB020 A Sub-Micron Resolution, Bunch-by-Bunch Beam Trajectory Feedback System and Its Application to Reducing Wakefield Effects in Single-Pass Beamlines 1382
 
  • D.R. Bett, P. Burrows, C. Perry, R.L. Ramjiawan
    JAI, Oxford, United Kingdom
  • D.R. Bett
    CERN, Geneva, Switzerland
  • K. Kubo, T. Okugi, N. Terunuma
    KEK, Ibaraki, Japan
 
  A high-precision intra-bunch-train beam orbit feedback correction system has been developed and tested at the KEK Accelerator Test Facility, ATF2. The system uses the vertical position of the bunch measured at two beam position monitors to calculate a pair of kicks which are applied to the next bunch using two upstream kickers, thereby correcting both the vertical position and trajectory angle. Using trains of two electron bunches separated in time by 187.6ns, the system was optimised so as to stabilize the beam offset at the feedback BPMs to better than 350nm, yielding a local trajectory angle correction to within 250nrad. The quality of the correction was verified using three downstream witness BPMs and the results were found to be in agreement with the predictions of a linear lattice model used to propagate the beam trajectory from the feedback region. This same model predicts a corrected be am jitter of c.1nm at the focal point of the accelerator. Measurements with a beam size monitor at this location demonstrate that reducing the trajectory jitter of the beam by a factor of 4 also reduces the increase in the measured beam size as a function of beam charge by a factor of ~1.6.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2021-TUPAB020  
About • paper received ※ 13 May 2021       paper accepted ※ 01 July 2021       issue date ※ 11 August 2021  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)