IPAC2019 - List of Authors (Rogatto, G.M.)

Paper	Title	Page
TUPMP001	Design and Experimental Results of a 1.1kA/800V AC Power Supply for Sirius Booster Dipoles	1227
	C. Rodrigues, G.O. Brunheira, B.E. Limeira, G.M. Rogatto LNLS, Campinas, Brazil
	Sirius is a 4th generation synchrotron light source de-signed and being built by Brazilian Synchrotron Light Laboratory (LNLS), with first beam scheduled for 2019. Approximately thousand power supplies (PS) will be needed to feed all the magnets, being 57 to operate the booster injector. The two booster dipole PS are the most complex, not only due to their higher current (1.1 kA), voltage (800 V) and power (333 kW) output, but also because the current must follow a quasi-triangular waveform, from a value close to zero to almost the maximum in 320 ms and at a repetition rate of 2 Hz. Due to the high output values, each PS is formed by two sets in parallel of 4 modules in series, what means 8 modules with 550 A / 200 V output. In order to reduce the 2-Hz effect in the grid, each module has two main stages. The input stage has the function to regulate the average voltage in a capacitor bank consuming a constant RMS current from the grid, which value depends on of the PS average output power. The output stage has the function to transfer the energy from the capacitor bank to the load, with the output cur-rent following the reference waveform. This work describes this PS, showing its topology, some aspects of its design and obtained results.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUPMP001
About •	paper received ※ 13 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPMP002	Overview of Sirius Power Supply System	1230
	C. Rodrigues, G.O. Brunheira, B.E. Limeira, R.J. Marcondeli, M.G. Martins, G.R. Oliveira, A.R.D. Rodrigues, G.M. Rogatto, A.P.A. Silva, A.R. Silva, H. Sousa LNLS, Campinas, Brazil
	Sirius is a 4th generation synchrotron light source designed and under construction by Brazilian Syn-chrotron Light Laboratory (LNLS), which first beam is scheduled to operate in 2019. Almost a thousand Pow-er supplies (PS) will be needed to feed all magnets of the magnetic lattice, with outputs ranging from 10A to 1.1kA and 50W to 333kW. Almost all power supplies were designed at LNLS. Only three families of power modules were de-signed: low power (FBP), high power (FAP) and AC (FAC). Each PS can have up to 8 modules in a parallel or/and series association, in order to reach the rated output values. All PS are digitally controlled by the same hardware and firmware, also developed by LNLS, called Digital Regulation System (DRS), but with different parameter settings. The DRS is also responsible by the communi-cation with other systems, PS monitoring, data man-agement, etc. This work presents an overview of this system, showing the PS specifications, family topologies and results of tests.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUPMP002
About •	paper received ※ 13 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Design and Experimental Results of a 1.1kA/800V AC Power Supply for Sirius Booster Dipoles

1227

C. Rodrigues, G.O. Brunheira, B.E. Limeira, G.M. Rogatto
LNLS, Campinas, Brazil

Sirius is a 4th generation synchrotron light source de-signed and being built by Brazilian Synchrotron Light Laboratory (LNLS), with first beam scheduled for 2019. Approximately thousand power supplies (PS) will be needed to feed all the magnets, being 57 to operate the booster injector. The two booster dipole PS are the most complex, not only due to their higher current (1.1 kA), voltage (800 V) and power (333 kW) output, but also because the current must follow a quasi-triangular waveform, from a value close to zero to almost the maximum in 320 ms and at a repetition rate of 2 Hz. Due to the high output values, each PS is formed by two sets in parallel of 4 modules in series, what means 8 modules with 550 A / 200 V output. In order to reduce the 2-Hz effect in the grid, each module has two main stages. The input stage has the function to regulate the average voltage in a capacitor bank consuming a constant RMS current from the grid, which value depends on of the PS average output power. The output stage has the function to transfer the energy from the capacitor bank to the load, with the output cur-rent following the reference waveform. This work describes this PS, showing its topology, some aspects of its design and obtained results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUPMP001

About •

paper received ※ 13 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPMP002

Overview of Sirius Power Supply System

1230

C. Rodrigues, G.O. Brunheira, B.E. Limeira, R.J. Marcondeli, M.G. Martins, G.R. Oliveira, A.R.D. Rodrigues, G.M. Rogatto, A.P.A. Silva, A.R. Silva, H. Sousa
LNLS, Campinas, Brazil

Sirius is a 4th generation synchrotron light source designed and under construction by Brazilian Syn-chrotron Light Laboratory (LNLS), which first beam is scheduled to operate in 2019. Almost a thousand Pow-er supplies (PS) will be needed to feed all magnets of the magnetic lattice, with outputs ranging from 10A to 1.1kA and 50W to 333kW. Almost all power supplies were designed at LNLS. Only three families of power modules were de-signed: low power (FBP), high power (FAP) and AC (FAC). Each PS can have up to 8 modules in a parallel or/and series association, in order to reach the rated output values. All PS are digitally controlled by the same hardware and firmware, also developed by LNLS, called Digital Regulation System (DRS), but with different parameter settings. The DRS is also responsible by the communi-cation with other systems, PS monitoring, data man-agement, etc. This work presents an overview of this system, showing the PS specifications, family topologies and results of tests.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUPMP002

About •

paper received ※ 13 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)