| Paper | Title | Page |
|---|---|---|
| MOPGW128 | Simulation and Analysis of Wake Fields and Trapped RF Modes in Insertion Device Vacuum Chambers at the Canadian Light Source | 414 |
|
||
|
Funding: CFI, NSERC, NRC, CIHR, the Province of Saskatchewan, WD, WESTGRID, Compute Canada, and the University of Saskatchewan The Canadian Light Source (CLS) synchrotron operates with four in-vacuum insertion devices, three in-vacuum undulators, and one in-vacuum wiggler. Presently, each of the devices occupies half of a straight section. The wiggler is unique in our ring as it is both in-vacuum and shares a straight section with an in-vacuum undulator. We have observed gap dependent beam instabilities in the undulator located in the straight section. In order to better understand the problem, the cause of the instabilities was investigated using 3D electromagnetic modelling. First, the ’trapped’ RF modes (natural resonances) for this undulator chamber, their Q value, and their peak frequencies were analysed using Eigenmode simulation. Secondly, beam excitation of the Eigenmodes was simulated with the Wakefield solver. Herein we present the results of this electromagnetic modelling. |
||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-MOPGW128 | |
| About • | paper received ※ 14 May 2019 paper accepted ※ 23 May 2019 issue date ※ 21 June 2019 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| TUPRB004 | Magnetic Measurements of Insertion Devices Using the Vibrating Wire Technique | 1683 |
|
||
| The commissioning of new in-vacuum insertion devices (ID) at the Canadian Light Source has motivated the assembly and development of a vibrating wire system. The advantage of the technique is that it is a sensitive magnetic measurement instrument at relatively low cost. Moreover, most hall probe systems require transverse access, which is often not available for in-vacuum or Delta-like devices. It is comparatively simple to string a taut wire through the gap of an in-vacuum ID. We describe the experimental challenges in mapping the field of an 80 mm period in-vacuum wiggler, IVW80, using the vibrating wire technique, and compare results against simulation and data obtained from Hall probe measurements. | ||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-TUPRB004 | |
| About • | paper received ※ 08 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| THPTS006 | Upgrade of the Canadian Light Source Booster RF System to Solid State | 4112 |
|
||
|
Funding: CFI, NSERC, NRC, CIHR, the Province of Saskatchewan, WD, and the University of Saskatchewan The Canadian Light Source synchrotron (CLS) had first light in 2004. For the last 14 years of operation we have exclusively used klystrons to provide RF power to our linac, booster, and storage ring. The klystrons represent a single point of failure for the operation of our booster and storage ring. This is especially poignant in the case of our booster ring klystron which is no longer manufactured. We have chosen to move to solid state amplifier (SSA) RF technology for its implicit high redundancy, modularity, ease of maintenance, and efficiency. Herein we review the performance parameters of our upgraded booster RF to a 100 kW 500 MHz transmitter built by Cryoelectra. |
||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2019-THPTS006 | |
| About • | paper received ※ 08 May 2019 paper accepted ※ 22 May 2019 issue date ※ 21 June 2019 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |