IPAC2016 - List of Authors (Lu, Z.J.)

Paper	Title	Page
MOPMY014	Design Study of RF Section and Cavities for Cepc 650 MHz Klystron	543
	O. Xiao Institute of High Energy Physics (IHEP), People's Republic of China D.D. Dong, S. Fukuda, Z.J. Lu, G. Pei, S.C. Wang, .. Zaib-un-Nisa, Z.S. Zhou IHEP, Beijing, People's Republic of China S. Fukuda KEK, Ibaraki, Japan
	An 800 kW CW klystron operating at 650 MHz is de-veloped for CEPC at Institute of High Energy Physics in China. The conceptual design has been finished and the main parameters are presented in this paper. A 1D large signal disk model code, AJDISK, has been used to design and optimize klystron RF section parameters. In addition, the RF cavities have been designed using SUPERFISH, HFSS and CST.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-MOPMY014
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPMY015	Design Study of Electron Gun for CEPC 650 MHz Klystron	546
SUPSS097	use link to see paper's listing under its alternate paper code
	.. Zaib-un-Nisa, D.D. Dong, Z.J. Lu, G. Pei, S.C. Wang, O. Xiao, Z.S. Zhou IHEP, Beijing, People's Republic of China S. Fukuda KEK, Ibaraki, Japan
	This paper presents the design and simulation of an electron gun for 800 kW CW klystron of which frequency is 650 MHz for CEPC project. An electron gun with a modulating anode is designed using DGUN software. The uniform beam trajectories, with a beam perveance of 0.64μA/V 3/2 are simulated. We employed a Ba-dispenser cathode of radius 35 mm with Φ10 hole at the center and obtained a current density on cathode less than 0.45 A/cm². The beam trajectories were also simulated over whole tube length with a magnetic field of 207 Gauss. Expecting functions using the modulating anode gun are also described. Proposed beam tester and whole CEPC klystron layout are also shown in this paper.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-MOPMY015
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPOR046	CEPC 650 MHz Klystron Development	3891
	Z.S. Zhou, D. Dong, S. Fukuda, Z.J. Lu, G. Pei, S.C. Wang, O. Xiao, .. Zaib-un-Nisa IHEP, Beijing, People's Republic of China S. Fukuda KEK, Ibaraki, Japan
	The CEPC collider beam power is about 100 MW, so the efficiency of amplifier is very important for cost of project implementation. The high power klystron is the more attractive because of its potential for higher eﬃciency than solid state amplifier. For CEPC klystron output power is not so high, the operation voltage can be a safe value. Advantage for single beam: reliable, low phase noise, some perspective technology can be used to improve efficiency. The accelerating frequency is 650 MHz, output power is a maximum power of 800kW, and efficiency is about 70%. In this paper, the specifications and developments of 650 MHz CW klystron, including the klystron gun prototype and future high efficiency consideration are summarized.
DOI •	reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-THPOR046
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Design Study of RF Section and Cavities for Cepc 650 MHz Klystron

543

O. Xiao
Institute of High Energy Physics (IHEP), People's Republic of China
D.D. Dong, S. Fukuda, Z.J. Lu, G. Pei, S.C. Wang, .. Zaib-un-Nisa, Z.S. Zhou
IHEP, Beijing, People's Republic of China
S. Fukuda
KEK, Ibaraki, Japan

An 800 kW CW klystron operating at 650 MHz is de-veloped for CEPC at Institute of High Energy Physics in China. The conceptual design has been finished and the main parameters are presented in this paper. A 1D large signal disk model code, AJDISK, has been used to design and optimize klystron RF section parameters. In addition, the RF cavities have been designed using SUPERFISH, HFSS and CST.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-MOPMY014

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

MOPMY015

Design Study of Electron Gun for CEPC 650 MHz Klystron

546

SUPSS097

use link to see paper's listing under its alternate paper code

.. Zaib-un-Nisa, D.D. Dong, Z.J. Lu, G. Pei, S.C. Wang, O. Xiao, Z.S. Zhou
IHEP, Beijing, People's Republic of China
S. Fukuda
KEK, Ibaraki, Japan

This paper presents the design and simulation of an electron gun for 800 kW CW klystron of which frequency is 650 MHz for CEPC project. An electron gun with a modulating anode is designed using DGUN software. The uniform beam trajectories, with a beam perveance of 0.64μA/V 3/2 are simulated. We employed a Ba-dispenser cathode of radius 35 mm with Φ10 hole at the center and obtained a current density on cathode less than 0.45 A/cm². The beam trajectories were also simulated over whole tube length with a magnetic field of 207 Gauss. Expecting functions using the modulating anode gun are also described. Proposed beam tester and whole CEPC klystron layout are also shown in this paper.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-MOPMY015

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPOR046

CEPC 650 MHz Klystron Development

3891

Z.S. Zhou, D. Dong, S. Fukuda, Z.J. Lu, G. Pei, S.C. Wang, O. Xiao, .. Zaib-un-Nisa
IHEP, Beijing, People's Republic of China
S. Fukuda
KEK, Ibaraki, Japan

The CEPC collider beam power is about 100 MW, so the efficiency of amplifier is very important for cost of project implementation. The high power klystron is the more attractive because of its potential for higher eﬃciency than solid state amplifier. For CEPC klystron output power is not so high, the operation voltage can be a safe value. Advantage for single beam: reliable, low phase noise, some perspective technology can be used to improve efficiency. The accelerating frequency is 650 MHz, output power is a maximum power of 800kW, and efficiency is about 70%. In this paper, the specifications and developments of 650 MHz CW klystron, including the klystron gun prototype and future high efficiency consideration are summarized.

DOI •

reference for this paper ※ DOI:10.18429/JACoW-IPAC2016-THPOR046

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)