IPAC2013 - List of Authors (Bracco, C.)

Paper

Title

Page

Simulations and Measurements of Cleaning with 100 MJ Beams in the LHC

52

R. Bruce, R.W. Aßmann, V. Boccone, C. Bracco, M. Cauchi, F. Cerutti, D. Deboy, A. Ferrari, L. Lari, A. Marsili, A. Mereghetti, E. Quaranta, S. Redaelli, G. Robert-Demolaize, A. Rossi, B. Salvachua, E. Skordis, G. Valentino, V. Vlachoudis, Th. Weiler, D. Wollmann
CERN, Geneva, Switzerland
L. Lari
IFIC, Valencia, Spain
E. Quaranta
Politecnico/Milano, Milano, Italy
G. Valentino
University of Malta, Information and Communication Technology, Msida, Malta

The CERN Large Hadron Collider is routinely storing proton beam intensities of more than 100 MJ, which puts extraordinary demands on the control of beam losses to avoid quenches of the superconducting magnets. Therefore, a detailed understanding of the LHC beam cleaning is required. We present tracking and shower simulations of the LHC's multi-stage collimation system and compare with measured beam losses, which allow us to conclude on the predictive power of the simulations.

Slides MOODB202 [6.343 MB]

MOPFI057

Studies for the LHeC Beam Transfer Systems

410

C. Bracco, B. Goddard
CERN, Geneva, Switzerland

The LHeC would allow for collisions between an electron beam from a new accelerator with the existing LHC hadron beam. Two possible configurations were studied: a separate LINAC (LINAC-ring) or a new electron ring superimposed on the LHC (ring-ring). The racetrack LINAC is now considered as the baseline for the LHeC design, with the ring-ring solution a back up. The studies performed for all the considered options are presented in this paper. For the LINAC-ring option the requirements for the post-collision line and the beam dump design have been evaluated in the cases of a 140 GeV and a 60 GeV electron beam. In the ring-ring option studies have been performed of the optics design of the transfer line from the a 10 GeV injector LINAC into the LHeC ring and of the injection system. The internal 60 GeV electron ring dump design has also been considered.

MOPFI060

Beam Transfer to LHC with the Low Gamma-transition SPS Optics

419

G. Vanbavinckhove, W. Bartmann, H. Bartosik, C. Bracco, L.N. Drøsdal, B. Goddard, V. Kain, M. Meddahi, V. Mertens, Y. Papaphilippou, J.A. Uythoven, J. Wenninger
CERN, Geneva, Switzerland
E. Gianfelice-Wendt
Fermilab, Batavia, USA

A new low gamma-transition optics with a lower integer tune, was introduced in the SPS to improve beam stability at high intensity. For transferring the beam to the LHC, the extraction bumps, extraction kickers and transfer lines needed to be adapted to the new optics. In particular, the transfer lines were re-matched and re-commissioned with the new optics. The first operational results are discussed for the SPS extraction, the transfer lines and the LHC injection. A detailed comparison is presented between the old and the new optics of the trajectories, dispersion, losses and other performance aspects.

MOPWO033

Analysis of LHC Transfer Line Trajectory Drifts

960

L.N. Drøsdal, W. Bartmann, H. Bartosik, C. Bracco, B. Goddard, V. Kain, Y. Papaphilippou, J.A. Uythoven, G. Vanbavinckhove, J. Wenninger
CERN, Geneva, Switzerland
E. Gianfelice-Wendt
Fermilab, Batavia, USA

The LHC is filled from the SPS via two 3km long transfer lines. In the first years of LHC operation large trajectory variations were discovered. The sources of bunch-by-bunch and shot-by-shot trajectory variations had been identified and improved by the 2012 LHC run. The origins of the longer term drifts were however still unclear and significant time was spent correcting the trajectories. In the last part of the 2012 run the optics in the SPS was changed to lower transition energy. Trajectory stability and correction frequency will be compared between before and after the optics change in the SPS. The sources of the variations have now been identified and will be discussed in this paper. Remedies for operation after the long shutdown will be proposed.

MOPWO046

Simulations and Measurements of Beam Losses on LHC Collimators during Beam Abort Failures

996

L. Lari, C. Bracco, R. Bruce, B. Goddard, S. Redaelli, B. Salvachua, G. Valentino
CERN, Geneva, Switzerland
A. Faus-Golfe, L. Lari
IFIC, Valencia, Spain
G. Valentino
University of Malta, Information and Communication Technology, Msida, Malta

Funding: The HiLumi LHC Design Study is included in the HL-LHC project and is partly funded by the European Commission within the Framework Programme 7 Capacities Specific Programme, Grant Agreement 284404.
One of the main purposes of tracking simulations for collimation studies is to produce loss maps along the LHC ring, in order to identify the level of local beam losses during nominal and abnormal operation scenarios. The SixTrack program is the standard tracking tool used at CERN to perform these studies. Recently, it was expanded in order to evaluate the proton load on different collimators in case of fast beam failures. Simulations are compared with beam measurements at 4 TeV. Combined failures are assumed which provide worst-case scenarios of the load on tungsten tertiary collimators.

TUPEA008

Physics of the AWAKE Project

1179

P. Muggli, E. Oz, R. Tarkeshian
MPI, Muenchen, Germany
C. Bracco, E. Gschwendtner, A. Pardons
CERN, Geneva, Switzerland
A. Caldwell, O. Reimann
MPI-P, München, Germany
K.V. Lotov
BINP SB RAS, Novosibirsk, Russia
A.M. Pukhov
HHUD, Dusseldorf, Germany
J. Vieira
IPFN, Lisbon, Portugal
M. Wing
UCL, London, United Kingdom

The goal of the AWKAKE collaboration is the study of plasma wakefields driven by proton (p⁺) bunches through experiments, simulations and theory. Proton bunches are interesting wakefield drivers because they can be ultra-relativistic (TeVs/p⁺) and carry large amounts of energy (>kJ). It was demonstrated in simulations* that acceleration of an electron (e-) bunch from 10GeV to >500GeV can be achieved in ~500m of plasma driven by a 1TeV, 100micron-long, bunch with 10¹¹ p+. Such short p⁺ bunches do not exist today. It was suggested** that a p⁺ bunch long compared to the plasma period can transversely self-modulate and resonantly drive wakefields to large amplitudes (~GV/m). Initial experiments based on self-modulation instability (SMI) will use single 12cm-long CERN SPS bunches with 1-3·10¹¹, 450GeV p⁺ to study physics of SMI. With a plasma density of 7·10¹⁴/cc the plasma wave and modulation period is 1.3mm. The SMI saturates after ~3m with amplitude in the GV/m range. Later a low energy (~10MeV) witness e^- bunch will be injected at the SMI saturation point. Energy gain over ~7m of plasma can reach the GeV level. Translation from physics to experimental plan and setup will be presented.
* A. Caldwell et al., Nature Physics 5, 363 (2009)
** N. Kumar et al., Phys. Rev. Lett. 104, 255003 (2010)

TUPEA051

Beam Transfer Line Design for a Plasma Wakefield Acceleration Experiment (AWAKE) at the CERN SPS

1247

C. Bracco, J. Bauche, D. Brethoux, V. Clerc, B. Goddard, E. Gschwendtner, L.K. Jensen, A. Kosmicki, G. Le Godec, M. Meddahi, C. Mutin, J.A. Osborne, K.D. Papastergiou, A. Pardons, F.M. Velotti, H. Vincke
CERN, Geneva, Switzerland
P. Muggli
MPI, Muenchen, Germany

The world’s first proton driven plasma wakefield acceleration experiment is presently being studied at CERN. The experiment will use a high energy proton beam extracted from the SPS as driver. Two possible locations for installing the AWAKE facility are considered: the West Area and the CNGS long baseline beam-line. The previous transfer line from the SPS to the West Area was completely dismantled in 2000 and it would need to be fully re-designed and re-built. For this option, geometric constraints for radio protection reasons would limit the maximum proton beam energy to 300 GeV. The existing CNGS line could be used by applying only minor changes to the final part of the lattice for the final focusing and the interface between the proton beam and the laser, required for plasma ionisation and bunch-modulation seeding. The beam line design studies performed for the two options are presented.

TUPEA053

Feasibility Study of the AWAKE Facility at CERN

1253

E. Gschwendtner, C. Bracco, B. Goddard, M. Meddahi, A. Pardons, E.N. Shaposhnikova, H. Timko, F.M. Velotti, H. Vincke
CERN, Geneva, Switzerland

Plasma Wakefield acceleration is a rapidly developing field which appears to be a promising candidate technology for future high-energy accelerators. The Proton Driven Plasma Wakefield Acceleration has been proposed as an approach to eventually accelerate an electron beam to the TeV energy range in a single plasma section. To verify this novel technique, a proof-of-principle demonstration experiment, AWAKE, is proposed using 400 GeV proton bunches from the SPS. Detailed studies on the identification of the best site for the installation of the AWAKE facility resulted in proposing the CNGS facility as best location. Design and integration layouts covering the beam line, the experimental area and all interfaces and services will be shown. Among other issues, radiation protection, safety and civil engineering constraints will be raised.

TUPFI027

Energy Deposition Studies for Fast Losses during LHC Injection Failures

1397

A. Lechner, A. Alnuaimi, C. Bracco, F. Cerutti, A. Christov, L.S. Esposito, N.V. Shetty, V. Vlachoudis
CERN, Geneva, Switzerland

Several instances of injection kicker magnet (MKI) failures have occurred in the first years of LHC operation, leading to misinjections or to accidental kicks of circulating bunches. In a few cases, MKI modules imparted a partial or an increased beam deflection, resulting in grazing bunch impact on beam-intercepting devices and consequently leading to significant secondary showers to downstream accelerator elements. In this study, we investigate different failure occurrences where miskicked bunches were incident on the injection beam stopper (TDI) and on one of the auxiliary injection collimators (TCLIB), respectively. FLUKA shower calculations were performed to quantify the energy deposition in superconducting magnets. Different sections of the LHC insertion regions 2 and 8 were studied, including the separation dipole and the inner triplet downstream of the TDI as well as matching section and dispersion suppressor adjacent to the TCLIB. The obtained results are evaluated in view of quench and damage limits.

TUPME032

Update on Beam Induced RF Heating in the LHC

1646

B. Salvant, O. Aberle, G. Arduini, R.W. Aßmann, V. Baglin, M.J. Barnes, W. Bartmann, P. Baudrenghien, O.E. Berrig, A. Bertarelli, C. Bracco, E. Bravin, G. Bregliozzi, R. Bruce, F. Carra, F. Caspers, G. Cattenoz, S.D. Claudet, H.A. Day, M. Deile, J.F. Esteban Müller, P. Fassnacht, M. Garlaschè, L. Gentini, B. Goddard, A. Grudiev, B. Henrist, S. Jakobsen, O.R. Jones, O. Kononenko, G. Lanza, L. Lari, T. Mastoridis, V. Mertens, N. Mounet, E. Métral, A.A. Nosych, J.L. Nougaret, S. Persichelli, A.M. Piguiet, S. Redaelli, F. Roncarolo, G. Rumolo, B. Salvachua, M. Sapinski, R. Schmidt, E.N. Shaposhnikova, L.J. Tavian, M.A. Timmins, J.A. Uythoven, A. Vidal, J. Wenninger, D. Wollmann, M. Zerlauth
CERN, Geneva, Switzerland
H.A. Day
UMAN, Manchester, United Kingdom
L. Lari
IFIC, Valencia, Spain

Since June 2011, the rapid increase of the luminosity performance of the LHC has come at the expense of increased temperature and pressure readings on specific near-beam LHC equipment. In some cases, this beam induced heating has caused delays whilie equipment cools down, beam dumps and even degradation of these devices. This contribution gathers the observations of beam induced heating attributable to beam coupling impedance, their current level of understanding and possible actions that are planned to be implemented during the long shutdown in 2013-2014.

THPEA041

Performance Improvements of the SPS Internal Beam Dump for the HL-LHC Beam

3231

F.M. Velotti, O. Aberle, C. Bracco, E. Carlier, P. Chiggiato, J.A. Ferreira Somoza, B. Goddard, M. Meddahi, V. Senaj, J.A. Uythoven
CERN, Geneva, Switzerland

The SPS internal beam dump has been designed for beam specifications well below the HL-LHC ones, and for modes of operation which may not be adequate for the HL-LHC era. The present system suffers from several limitations in the allowed intensity and energy range, and its vacuum performance affects nearby high-voltage kicker systems. In this report the limitations of the internal beam dump system are reviewed, and the possible improvements compared. Preliminary upgrade proposals are presented, taking into consideration the expected operational HL-LHC parameters.

THPEA045

Beam Induced Quenches of LHC Magnets

3243

M. Sapinski, T. Baer, M. Bednarek, G. Bellodi, C. Bracco, R. Bruce, B. Dehning, W. Höfle, A. Lechner, E. Nebot Del Busto, A. Priebe, S. Redaelli, B. Salvachua, R. Schmidt, D. Valuch, A.P. Verweij, J. Wenninger, D. Wollmann, M. Zerlauth
CERN, Geneva, Switzerland

In the years 2009-2013 LHC was operating with the beam energy of 3.5 and 4 TeV instead of the nominal 7 TeV, with the corresponding currents in the superconducting magnets also half nominal. To date only a small number of beam-induced quenches have occurred, with most being due to specially designed quench tests. During normal collider operation with stored beam there has not been a single beam induced quench. This excellent result is mainly explained by the fact that the cleaning of the beam halo worked very well and, in case of beam losses, the beam was dumped before any significant energy was deposited in the magnets. However, conditions are expected to become much tougher after the long LHC shutdown, when the magnets will be working at near nominal currents in the presence of high energy and intensity beams. This paper summarizes the experience to date with beam-induced quenches. It describes the techniques used to generate controlled quench conditions which were used to study the limitations. Results are discussed along with their implication for LHC operation after the first Long Shutdown.

THPWO080

Operational Performance of the LHC Proton Beams with the SPS Low Transition Energy Optics

3945

Y. Papaphilippou, G. Arduini, T. Argyropoulos, W. Bartmann, H. Bartosik, T. Bohl, C. Bracco, S. Cettour-Cave, K. Cornelis, L.N. Drøsdal, J.F. Esteban Müller, B. Goddard, A. Guerrero, W. Höfle, V. Kain, G. Rumolo, B. Salvant, E.N. Shaposhnikova, H. Timko, D. Valuch, G. Vanbavinckhove, J. Wenninger
CERN, Geneva, Switzerland
E. Gianfelice-Wendt
Fermilab, Batavia, USA

An optics in the SPS with lower integer tunes (20 versus 26) was proposed and introduced in machine studies since 2010, as a measure for increasing transverse and longitudinal instability thresholds, especially at low energy, for the LHC proton beams. After two years of machine studies and careful optimisation, the new “Q20” optics became operational in September 2012 and steadily delivered beam to the LHC until the end of the run. This paper reviews the operational performance of the Q20 optics with respect to transverse and longitudinal beam characteristics in the SPS, enabling high brightness beams injected into the LHC. Aspects of longitudinal beam stability, transmission, high-energy orbit control and beam transfer are discussed.

Paper	Title	Page
MOODB202	Simulations and Measurements of Cleaning with 100 MJ Beams in the LHC	52
	R. Bruce, R.W. Aßmann, V. Boccone, C. Bracco, M. Cauchi, F. Cerutti, D. Deboy, A. Ferrari, L. Lari, A. Marsili, A. Mereghetti, E. Quaranta, S. Redaelli, G. Robert-Demolaize, A. Rossi, B. Salvachua, E. Skordis, G. Valentino, V. Vlachoudis, Th. Weiler, D. Wollmann CERN, Geneva, Switzerland L. Lari IFIC, Valencia, Spain E. Quaranta Politecnico/Milano, Milano, Italy G. Valentino University of Malta, Information and Communication Technology, Msida, Malta
	The CERN Large Hadron Collider is routinely storing proton beam intensities of more than 100 MJ, which puts extraordinary demands on the control of beam losses to avoid quenches of the superconducting magnets. Therefore, a detailed understanding of the LHC beam cleaning is required. We present tracking and shower simulations of the LHC's multi-stage collimation system and compare with measured beam losses, which allow us to conclude on the predictive power of the simulations.
	Slides MOODB202 [6.343 MB]

MOPFI057	Studies for the LHeC Beam Transfer Systems	410
	C. Bracco, B. Goddard CERN, Geneva, Switzerland
	The LHeC would allow for collisions between an electron beam from a new accelerator with the existing LHC hadron beam. Two possible configurations were studied: a separate LINAC (LINAC-ring) or a new electron ring superimposed on the LHC (ring-ring). The racetrack LINAC is now considered as the baseline for the LHeC design, with the ring-ring solution a back up. The studies performed for all the considered options are presented in this paper. For the LINAC-ring option the requirements for the post-collision line and the beam dump design have been evaluated in the cases of a 140 GeV and a 60 GeV electron beam. In the ring-ring option studies have been performed of the optics design of the transfer line from the a 10 GeV injector LINAC into the LHeC ring and of the injection system. The internal 60 GeV electron ring dump design has also been considered.

MOPFI060	Beam Transfer to LHC with the Low Gamma-transition SPS Optics	419
	G. Vanbavinckhove, W. Bartmann, H. Bartosik, C. Bracco, L.N. Drøsdal, B. Goddard, V. Kain, M. Meddahi, V. Mertens, Y. Papaphilippou, J.A. Uythoven, J. Wenninger CERN, Geneva, Switzerland E. Gianfelice-Wendt Fermilab, Batavia, USA
	A new low gamma-transition optics with a lower integer tune, was introduced in the SPS to improve beam stability at high intensity. For transferring the beam to the LHC, the extraction bumps, extraction kickers and transfer lines needed to be adapted to the new optics. In particular, the transfer lines were re-matched and re-commissioned with the new optics. The first operational results are discussed for the SPS extraction, the transfer lines and the LHC injection. A detailed comparison is presented between the old and the new optics of the trajectories, dispersion, losses and other performance aspects.

MOPWO033	Analysis of LHC Transfer Line Trajectory Drifts	960
	L.N. Drøsdal, W. Bartmann, H. Bartosik, C. Bracco, B. Goddard, V. Kain, Y. Papaphilippou, J.A. Uythoven, G. Vanbavinckhove, J. Wenninger CERN, Geneva, Switzerland E. Gianfelice-Wendt Fermilab, Batavia, USA
	The LHC is filled from the SPS via two 3km long transfer lines. In the first years of LHC operation large trajectory variations were discovered. The sources of bunch-by-bunch and shot-by-shot trajectory variations had been identified and improved by the 2012 LHC run. The origins of the longer term drifts were however still unclear and significant time was spent correcting the trajectories. In the last part of the 2012 run the optics in the SPS was changed to lower transition energy. Trajectory stability and correction frequency will be compared between before and after the optics change in the SPS. The sources of the variations have now been identified and will be discussed in this paper. Remedies for operation after the long shutdown will be proposed.

MOPWO046	Simulations and Measurements of Beam Losses on LHC Collimators during Beam Abort Failures	996
	L. Lari, C. Bracco, R. Bruce, B. Goddard, S. Redaelli, B. Salvachua, G. Valentino CERN, Geneva, Switzerland A. Faus-Golfe, L. Lari IFIC, Valencia, Spain G. Valentino University of Malta, Information and Communication Technology, Msida, Malta
	Funding: The HiLumi LHC Design Study is included in the HL-LHC project and is partly funded by the European Commission within the Framework Programme 7 Capacities Specific Programme, Grant Agreement 284404. One of the main purposes of tracking simulations for collimation studies is to produce loss maps along the LHC ring, in order to identify the level of local beam losses during nominal and abnormal operation scenarios. The SixTrack program is the standard tracking tool used at CERN to perform these studies. Recently, it was expanded in order to evaluate the proton load on different collimators in case of fast beam failures. Simulations are compared with beam measurements at 4 TeV. Combined failures are assumed which provide worst-case scenarios of the load on tungsten tertiary collimators.

TUPEA008	Physics of the AWAKE Project	1179
	P. Muggli, E. Oz, R. Tarkeshian MPI, Muenchen, Germany C. Bracco, E. Gschwendtner, A. Pardons CERN, Geneva, Switzerland A. Caldwell, O. Reimann MPI-P, München, Germany K.V. Lotov BINP SB RAS, Novosibirsk, Russia A.M. Pukhov HHUD, Dusseldorf, Germany J. Vieira IPFN, Lisbon, Portugal M. Wing UCL, London, United Kingdom
	The goal of the AWKAKE collaboration is the study of plasma wakefields driven by proton (p⁺) bunches through experiments, simulations and theory. Proton bunches are interesting wakefield drivers because they can be ultra-relativistic (TeVs/p⁺) and carry large amounts of energy (>kJ). It was demonstrated in simulations* that acceleration of an electron (e-) bunch from 10GeV to >500GeV can be achieved in ~500m of plasma driven by a 1TeV, 100micron-long, bunch with 10¹¹ p+. Such short p⁺ bunches do not exist today. It was suggested** that a p⁺ bunch long compared to the plasma period can transversely self-modulate and resonantly drive wakefields to large amplitudes (~GV/m). Initial experiments based on self-modulation instability (SMI) will use single 12cm-long CERN SPS bunches with 1-3·10¹¹, 450GeV p⁺ to study physics of SMI. With a plasma density of 7·10¹⁴/cc the plasma wave and modulation period is 1.3mm. The SMI saturates after ~3m with amplitude in the GV/m range. Later a low energy (~10MeV) witness e^- bunch will be injected at the SMI saturation point. Energy gain over ~7m of plasma can reach the GeV level. Translation from physics to experimental plan and setup will be presented. * A. Caldwell et al., Nature Physics 5, 363 (2009) ** N. Kumar et al., Phys. Rev. Lett. 104, 255003 (2010)

TUPEA051	Beam Transfer Line Design for a Plasma Wakefield Acceleration Experiment (AWAKE) at the CERN SPS	1247
	C. Bracco, J. Bauche, D. Brethoux, V. Clerc, B. Goddard, E. Gschwendtner, L.K. Jensen, A. Kosmicki, G. Le Godec, M. Meddahi, C. Mutin, J.A. Osborne, K.D. Papastergiou, A. Pardons, F.M. Velotti, H. Vincke CERN, Geneva, Switzerland P. Muggli MPI, Muenchen, Germany
	The world’s first proton driven plasma wakefield acceleration experiment is presently being studied at CERN. The experiment will use a high energy proton beam extracted from the SPS as driver. Two possible locations for installing the AWAKE facility are considered: the West Area and the CNGS long baseline beam-line. The previous transfer line from the SPS to the West Area was completely dismantled in 2000 and it would need to be fully re-designed and re-built. For this option, geometric constraints for radio protection reasons would limit the maximum proton beam energy to 300 GeV. The existing CNGS line could be used by applying only minor changes to the final part of the lattice for the final focusing and the interface between the proton beam and the laser, required for plasma ionisation and bunch-modulation seeding. The beam line design studies performed for the two options are presented.

TUPEA053	Feasibility Study of the AWAKE Facility at CERN	1253
	E. Gschwendtner, C. Bracco, B. Goddard, M. Meddahi, A. Pardons, E.N. Shaposhnikova, H. Timko, F.M. Velotti, H. Vincke CERN, Geneva, Switzerland
	Plasma Wakefield acceleration is a rapidly developing field which appears to be a promising candidate technology for future high-energy accelerators. The Proton Driven Plasma Wakefield Acceleration has been proposed as an approach to eventually accelerate an electron beam to the TeV energy range in a single plasma section. To verify this novel technique, a proof-of-principle demonstration experiment, AWAKE, is proposed using 400 GeV proton bunches from the SPS. Detailed studies on the identification of the best site for the installation of the AWAKE facility resulted in proposing the CNGS facility as best location. Design and integration layouts covering the beam line, the experimental area and all interfaces and services will be shown. Among other issues, radiation protection, safety and civil engineering constraints will be raised.

TUPFI027	Energy Deposition Studies for Fast Losses during LHC Injection Failures	1397
	A. Lechner, A. Alnuaimi, C. Bracco, F. Cerutti, A. Christov, L.S. Esposito, N.V. Shetty, V. Vlachoudis CERN, Geneva, Switzerland
	Several instances of injection kicker magnet (MKI) failures have occurred in the first years of LHC operation, leading to misinjections or to accidental kicks of circulating bunches. In a few cases, MKI modules imparted a partial or an increased beam deflection, resulting in grazing bunch impact on beam-intercepting devices and consequently leading to significant secondary showers to downstream accelerator elements. In this study, we investigate different failure occurrences where miskicked bunches were incident on the injection beam stopper (TDI) and on one of the auxiliary injection collimators (TCLIB), respectively. FLUKA shower calculations were performed to quantify the energy deposition in superconducting magnets. Different sections of the LHC insertion regions 2 and 8 were studied, including the separation dipole and the inner triplet downstream of the TDI as well as matching section and dispersion suppressor adjacent to the TCLIB. The obtained results are evaluated in view of quench and damage limits.

TUPME032	Update on Beam Induced RF Heating in the LHC	1646
	B. Salvant, O. Aberle, G. Arduini, R.W. Aßmann, V. Baglin, M.J. Barnes, W. Bartmann, P. Baudrenghien, O.E. Berrig, A. Bertarelli, C. Bracco, E. Bravin, G. Bregliozzi, R. Bruce, F. Carra, F. Caspers, G. Cattenoz, S.D. Claudet, H.A. Day, M. Deile, J.F. Esteban Müller, P. Fassnacht, M. Garlaschè, L. Gentini, B. Goddard, A. Grudiev, B. Henrist, S. Jakobsen, O.R. Jones, O. Kononenko, G. Lanza, L. Lari, T. Mastoridis, V. Mertens, N. Mounet, E. Métral, A.A. Nosych, J.L. Nougaret, S. Persichelli, A.M. Piguiet, S. Redaelli, F. Roncarolo, G. Rumolo, B. Salvachua, M. Sapinski, R. Schmidt, E.N. Shaposhnikova, L.J. Tavian, M.A. Timmins, J.A. Uythoven, A. Vidal, J. Wenninger, D. Wollmann, M. Zerlauth CERN, Geneva, Switzerland H.A. Day UMAN, Manchester, United Kingdom L. Lari IFIC, Valencia, Spain
	Since June 2011, the rapid increase of the luminosity performance of the LHC has come at the expense of increased temperature and pressure readings on specific near-beam LHC equipment. In some cases, this beam induced heating has caused delays whilie equipment cools down, beam dumps and even degradation of these devices. This contribution gathers the observations of beam induced heating attributable to beam coupling impedance, their current level of understanding and possible actions that are planned to be implemented during the long shutdown in 2013-2014.

THPEA041	Performance Improvements of the SPS Internal Beam Dump for the HL-LHC Beam	3231
	F.M. Velotti, O. Aberle, C. Bracco, E. Carlier, P. Chiggiato, J.A. Ferreira Somoza, B. Goddard, M. Meddahi, V. Senaj, J.A. Uythoven CERN, Geneva, Switzerland
	The SPS internal beam dump has been designed for beam specifications well below the HL-LHC ones, and for modes of operation which may not be adequate for the HL-LHC era. The present system suffers from several limitations in the allowed intensity and energy range, and its vacuum performance affects nearby high-voltage kicker systems. In this report the limitations of the internal beam dump system are reviewed, and the possible improvements compared. Preliminary upgrade proposals are presented, taking into consideration the expected operational HL-LHC parameters.

THPEA045	Beam Induced Quenches of LHC Magnets	3243
	M. Sapinski, T. Baer, M. Bednarek, G. Bellodi, C. Bracco, R. Bruce, B. Dehning, W. Höfle, A. Lechner, E. Nebot Del Busto, A. Priebe, S. Redaelli, B. Salvachua, R. Schmidt, D. Valuch, A.P. Verweij, J. Wenninger, D. Wollmann, M. Zerlauth CERN, Geneva, Switzerland
	In the years 2009-2013 LHC was operating with the beam energy of 3.5 and 4 TeV instead of the nominal 7 TeV, with the corresponding currents in the superconducting magnets also half nominal. To date only a small number of beam-induced quenches have occurred, with most being due to specially designed quench tests. During normal collider operation with stored beam there has not been a single beam induced quench. This excellent result is mainly explained by the fact that the cleaning of the beam halo worked very well and, in case of beam losses, the beam was dumped before any significant energy was deposited in the magnets. However, conditions are expected to become much tougher after the long LHC shutdown, when the magnets will be working at near nominal currents in the presence of high energy and intensity beams. This paper summarizes the experience to date with beam-induced quenches. It describes the techniques used to generate controlled quench conditions which were used to study the limitations. Results are discussed along with their implication for LHC operation after the first Long Shutdown.

THPWO080	Operational Performance of the LHC Proton Beams with the SPS Low Transition Energy Optics	3945
	Y. Papaphilippou, G. Arduini, T. Argyropoulos, W. Bartmann, H. Bartosik, T. Bohl, C. Bracco, S. Cettour-Cave, K. Cornelis, L.N. Drøsdal, J.F. Esteban Müller, B. Goddard, A. Guerrero, W. Höfle, V. Kain, G. Rumolo, B. Salvant, E.N. Shaposhnikova, H. Timko, D. Valuch, G. Vanbavinckhove, J. Wenninger CERN, Geneva, Switzerland E. Gianfelice-Wendt Fermilab, Batavia, USA
	An optics in the SPS with lower integer tunes (20 versus 26) was proposed and introduced in machine studies since 2010, as a measure for increasing transverse and longitudinal instability thresholds, especially at low energy, for the LHC proton beams. After two years of machine studies and careful optimisation, the new “Q20” optics became operational in September 2012 and steadily delivered beam to the LHC until the end of the run. This paper reviews the operational performance of the Q20 optics with respect to transverse and longitudinal beam characteristics in the SPS, enabling high brightness beams injected into the LHC. Aspects of longitudinal beam stability, transmission, high-energy orbit control and beam transfer are discussed.