| Paper | Title | Page |
|---|---|---|
| MOPC021 | Design of a Choke-mode Damped Accelerating Structure for CLIC Main Linac | 113 |
|
||
| Choke-mode damped accelerating structures are being studied as an alternative to the CLIC baseline structure by a CERN-Tsinghua collaboration. Choke-mode structures hold the potential for much lower levels of pulsed surface heating and, since milling is not needed, reduced cost. Structures with radial choke attached are simulated in Gdfidl to investigate the damping of the transverse wake. The first pass-band of the dipole modes is well damped, while the higher order dipole modes are possible to be reflected by the choke. Therefore, the geometry of the choke is tuned to minimize the reflection of these higher order dipoles. Based on this damping scheme, an accelerating structure with the same iris dimensions as the nominal CLIC design but with choke-mode damping has been designed. A prototype structure will be manufactured and high power tested in the near future. | ||
| MOPC022 | Development of a Compact C-band Photocathode RF Gun | 116 |
|
||
|
Funding: This work is supported by National Natural Science Foundation of China and National Basic Research Program of China (973 Program). A C-band photocathode RF gun for a compact electron diffraction facility is developed in Tsinghua University, which is designed to work at the frequency of 5.712GHz. This paper presents the physics and structure design of this C-band RF gun, and the comparison on beam dynamics of S-band and C-band photoinjector has been done. Some new structure design will be adopted in this gun, including the optimized cavity length and elliptical iris, which is helpful to achieve lower emittance and larger mode separation. |
||
| TUPC109 | Electron Bunch Slice Emittance Measurement with the Space Charge Effects* | 1272 |
|
||
|
Funding: supported by the National Natural Science Foundation of China (Grant Nos. 10735050, 10805031, 10875070 and 10925523), and the National Basic Research Program of China (Grant No. 2007CB815102). Since slice transverse emittance of the electron beam is critical to a high-gain short-wavelength FEL, its characterization is very important. For space charge dominated electron beam, conventional emittance measurement techniques, such as solenoid scanning and quadruple scanning, without considering space charge forces lead to large errors of emittance evaluations. This essay introduces a modified solenoid-scan method of slice emittance measurement for space charge dominated beam, and simulations show that the new method brings the emittance evaluations much closer to actual values. |
||
| THPC045 | Design of a Compact Storage Ring for the TTX | 3005 |
|
||
| We study a compact storage ring with circumference 3-m, 4 dipoles, and two quadrupoles for the Tsinghua Thomson scattering X-ray (TTX) source. The effects of Touschek lifetime, rf system requirement, the Intra-beam scattering (IBS) and coherent synchrotron radiation (CSR) will be addressed. A top-up injection system will be designed to maximize the Photon flux. Conceptual laser cavity to enhance photon flux will be discussed. Expected performance of the compact X-ray source will be presented. | ||
| THPC120 | Experimental Investigation of Photocathode Thermal Emittance Components with a Copper Cathode* | 3167 |
|
||
|
With progress of photocathode RF gun technology, thermal emittance has become the primary limitation of electron beam brightness*. Extensive efforts have been devoted to study thermal emittance, but experiment results diverge between research groups and few can be well interpreted**. One possibility is the undefined online cathode surface conditions, which may cause difference of work functions, field enhancement factor and surface roughness, and lead to thermal emittance divergence. In this paper, we report an experiment of characterizing online photocathode work function, field enhancement factor and surface roughness effect by measuring electric field dependence of photoemission quantum efficiency (QE) and thermal emittance in a Cu-cathode RF gun. Preliminary experiment results reveal huge thermal emittance contributed by surface roughness for the first time, and are in reasonable consistency with theoretical model prediction***.
*Ivan V. Bazarov et al., Phys. Rev. Lett. 102, 104801(2009) ** D.H. Dowell et al, Nucl. Instrum. Methods Phys. Res., Sect. A 622, 685 (2010). ***D. Xinag et al, PAC’07, 1049 (2007) |
||
| THPC121 | Design and Cold Tests of a Prototype photocathode RF Gun for Shanghai SXFEL Facility | 3170 |
|
||
| A soft X-ray (~9 nm) FEL (SXFEL) facility is going to be constructed in Shanghai, China, which requires high charge (>500 pC) electron beam with low transverse emittance (<1.5 mm-mrad) at photoinjector exit. One of the keys to achieve a low emittance with high charge is high gradient on the photocathode, so an S-band photocathode RF gun modified from BNL type gun is designed, which aims running 100 MV/m peak gradient at 10 Hz. By changing the cathode seal technique, removing the insertion RF tuner, and reducing the peak surface field, RF breakdown possibility is reduced. Besides, RF pulse width is also considered to be reduced to lower the RF breakdown possibility. Since zero mode and multipole field degrades the beam emittance, they are also suppressed in the new gun design. Design details and cold testing results are presented in this paper. | ||