IPAC2011 - List of Authors (Sako, H.)

Paper	Title	Page
TUPC100	Longitudinal Beam Profile Measurement at J-PARC Separated Drift Tube Linac	1245
	T. Maruta KEK/JAEA, Ibaraki-Ken, Japan M. Ikegami KEK, Ibaraki, Japan A. Miura, G.H. Wei JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan H. Sako JAEA, Ibaraki-ken, Japan
	We measured longitudinal beam profile at Separated Drift Tube Linac (SDTL) injection part by scanning beam transmission and beamloss at the downstream of SDTL section by changing SDTL injection phase. As the beam goes to acceptance edge, part of the beam which is out of acceptance isn't accelerate and finally it is lost by hitting to beam duct. Thus beam transmission shows sliced bunch shape by acceptance edge, it is possible to reconstruct the beam bunch shape. The result shows about 60% wider profile in both phi and E direction against to design.

WEPS046	Longitudinal Beam Acceptance of J-PARC Drift Tube Linac	2592
	T. Maruta KEK/JAEA, Ibaraki-Ken, Japan M. Ikegami KEK, Ibaraki, Japan A. Miura, G.H. Wei JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan H. Sako JAEA, Ibaraki-ken, Japan
	The longitudinal acceptance of the J-PARC Drift Tube Linac (DTL) was measured by synchronous phase scan method. The IMPACT simulation indicated DTL longitudinal acceptance is shrinked if the DTL tank level reduced, but beam energy finally acheved at the Linac is almost same as the case of nominal tank level. We measured the acceptance and confirmed the simulation is correct.

TUPC102	Measurement of Beam Loss Tracks by Scintillating Fibers at J-PARC Linac	1251
	H. Sako, T. Maruta, A. Miura JAEA/J-PARC, Tokai-mura, Japan
	Highest beam loss in the J-PARC linac has been observed that the ACS (Annular-Coupled Structure linac) section. Since the observed beam loss is proportional to the residual gas pressure, the source of the beam loss is considered as H0 produced in an interaction of H⁻ beams with remnant gas. If this assumption is valid, H0 hits the beam duct and changes into H⁺ and escapes from the beam duct. We constructed scintillation fiber hodoscopes to detect H⁺s and eventually identify the particle species as H⁺. The hodoscopes are made of 4 planes of hodoscopes which consists of 16 scintillation fibers of 64mm long and with 4mmx4mm cross section. We installed the hodoscopes at the upstream part of the ACS section and measured beam loss. The results are shown in this paper.

TUPC104	Beam Loss Detected by Scintillation Monitor	1257
	A. Miura, K. Hasegawa, T. Maruta, N. Ouchi, H. Sako JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan Z. Igarashi, M. Ikegami, T. Miyao KEK, Ibaraki, Japan
	Ar gas proportional BLMs have measured the beam loss through operations, but they are also sensitive to background noise of X-ray emitted from RF cavities. We have tried to measure the beam loss using scintillation monitors which would bring more accurate beam loss measurements with suppression of X-ray noise. We measured beam loss using scintillation beam loss monitors. Because this scintillation BLM is sensitive for low energy gamma-rays and fast neutrons, small signals from X-rays would be also detected. As the measurement results, a good signal to noise ratio is observed for the scintillation monitor with quite low sensitivity to the background X-ray. And many single events are observed in the intermediate pulse bunch with about 600 ns as pulse width. In addition, because we fabricated the filter and integrated circuit, total amount of X-ray noise can become smaller. We obtained the good performances of scintillation BLM with small effect of X-ray noise. This monitor can be used for beam loss measurement and a knob for tuning. Furthermore, because the detail structure can be detected, this monitor could be employed for another diagnostic device.

Paper

Title

Page

Longitudinal Beam Profile Measurement at J-PARC Separated Drift Tube Linac

1245

T. Maruta
KEK/JAEA, Ibaraki-Ken, Japan
M. Ikegami
KEK, Ibaraki, Japan
A. Miura, G.H. Wei
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
H. Sako
JAEA, Ibaraki-ken, Japan

We measured longitudinal beam profile at Separated Drift Tube Linac (SDTL) injection part by scanning beam transmission and beamloss at the downstream of SDTL section by changing SDTL injection phase. As the beam goes to acceptance edge, part of the beam which is out of acceptance isn't accelerate and finally it is lost by hitting to beam duct. Thus beam transmission shows sliced bunch shape by acceptance edge, it is possible to reconstruct the beam bunch shape. The result shows about 60% wider profile in both phi and E direction against to design.

WEPS046

Longitudinal Beam Acceptance of J-PARC Drift Tube Linac

2592

T. Maruta
KEK/JAEA, Ibaraki-Ken, Japan
M. Ikegami
KEK, Ibaraki, Japan
A. Miura, G.H. Wei
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
H. Sako
JAEA, Ibaraki-ken, Japan

The longitudinal acceptance of the J-PARC Drift Tube Linac (DTL) was measured by synchronous phase scan method. The IMPACT simulation indicated DTL longitudinal acceptance is shrinked if the DTL tank level reduced, but beam energy finally acheved at the Linac is almost same as the case of nominal tank level. We measured the acceptance and confirmed the simulation is correct.

TUPC102

Measurement of Beam Loss Tracks by Scintillating Fibers at J-PARC Linac

1251

H. Sako, T. Maruta, A. Miura
JAEA/J-PARC, Tokai-mura, Japan

Highest beam loss in the J-PARC linac has been observed that the ACS (Annular-Coupled Structure linac) section. Since the observed beam loss is proportional to the residual gas pressure, the source of the beam loss is considered as H0 produced in an interaction of H⁻ beams with remnant gas. If this assumption is valid, H0 hits the beam duct and changes into H⁺ and escapes from the beam duct. We constructed scintillation fiber hodoscopes to detect H⁺s and eventually identify the particle species as H⁺. The hodoscopes are made of 4 planes of hodoscopes which consists of 16 scintillation fibers of 64mm long and with 4mmx4mm cross section. We installed the hodoscopes at the upstream part of the ACS section and measured beam loss. The results are shown in this paper.

TUPC104

Beam Loss Detected by Scintillation Monitor

1257

A. Miura, K. Hasegawa, T. Maruta, N. Ouchi, H. Sako
JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
Z. Igarashi, M. Ikegami, T. Miyao
KEK, Ibaraki, Japan

Ar gas proportional BLMs have measured the beam loss through operations, but they are also sensitive to background noise of X-ray emitted from RF cavities. We have tried to measure the beam loss using scintillation monitors which would bring more accurate beam loss measurements with suppression of X-ray noise. We measured beam loss using scintillation beam loss monitors. Because this scintillation BLM is sensitive for low energy gamma-rays and fast neutrons, small signals from X-rays would be also detected. As the measurement results, a good signal to noise ratio is observed for the scintillation monitor with quite low sensitivity to the background X-ray. And many single events are observed in the intermediate pulse bunch with about 600 ns as pulse width. In addition, because we fabricated the filter and integrated circuit, total amount of X-ray noise can become smaller. We obtained the good performances of scintillation BLM with small effect of X-ray noise. This monitor can be used for beam loss measurement and a knob for tuning. Furthermore, because the detail structure can be detected, this monitor could be employed for another diagnostic device.