IPAC2011 - List of Authors (Roth, A.)

Paper	Title	Page
MOPC077	Commissioning of Multibunch Feedback Systems at the Fast Ramping Stretcher Ring ELSA	250
	A. Roth, F. Frommberger, N. Heurich, W. Hillert, M. Schedler, R. Zimmermann ELSA, Bonn, Germany
	Funding: Supported by German Research Foundation through SFB/TR 16 and by Helmholtz Alliance through HA-10¹. At the Electron Stretcher Facility ELSA of Bonn University, an external beam of either unpolarized or polarized electrons is supplied to hadron physics experiments. The ELSA stretcherring operates in the energy range of 1.2 to 3.5 GeV and achieves a duty cycle of up to 80% using a fast energy ramp of 4 GeV/s. Under these conditions, an increase of the internal beam current from an actual value of 20 mA up to 200 mA is planned. Such an upgrade is mainly limited by the excitation of multibunch instabilities. As one active counteraction, we have installed state-of-the-art bunch-by-bunch feedback systems for the longitudinal, as well as for both transverse planes. The detailed setup with all main components and first results of the commissioning of the systems will be presented. In particular, the performance of the longitudinal feedback with a stabilized synchrotron frequency during the fast energy ramp will be discussed.

MOPC078	Operation of Superconducting Cavities in a Fast Ramping Electron Storage Ring	253
	A. Roth, W. Hillert ELSA, Bonn, Germany
	Funding: Supported by German Research Foundation through SFB/TR 16. The achievable maximum energy of a medium-sized electron accelerator is mainly limited by the accelerating voltage. Using superconducting (sc) cavities, the energy limitation can be shifted considerably. However, the operation of sc multi-cell cavities in a fast ramping storage ring causes additional problems which were investigated at the 3.5 GeV Electron Stretcher Accelerator ELSA. We studied the use of two 500 MHz sc cavities providing the necessary resonator voltage of up to 14 MV and replacing the normal conducting cavities of PETRA type. A large cavity coupling factor is required, so that using the existing 250 kW klystron, an internal beam of 50 mA can be accelerated up to 5 GeV. In addition, a fast detuning of the resonance frequency of the cavities must be implemented during beam injection and the energy ramp of 4 GeV/s. An appropriate 500 MHz structure is given by a five-cell cavity constructed for the JAERI-FEL-LINAC. Based on this geometry, HOM have been calculated from a numerical simulation. Since all monopole and a larger number of dipole HOM are well above the multibunch instabilities threshold, further studies about beam instabilities damping are essential.

MOPO003	A Broadband RF Stripline Kicker for Damping Transversal Multibunch Instabilities	481
	M. Schedler, D. Heiliger, W. Hillert, A. Roth ELSA, Bonn, Germany
	When operating an RF feedback system, being able to reliably act upon every single bunch is a necessity. By employing a broadband RF stripline kicker, any bunch displacement can be corrected for. In a 500 MHz accelerator, the decay time of the electromagnetic field inside the kicker has to be less than 2 ns in order to avoid the following bunch to be affected. By designing the kicker as an RF coax device matched to the line impedance of the power cables, perturbing reflected signals are avoided. Additionally, the kicking strength and thus the shunt impedance should be maximized over the full spectrum from DC to 250 MHz. The kicker design has been optimized to meet the above requirements by relying on CST Microwave Studio simulations. Their results and first measurements are presented.

MOPO004	A Longitudinal Kicker Cavity for a Bunch-by-bunch Feedback System at ELSA	484
	N. Heurich, W. Hillert, A. Roth, R. Zimmermann ELSA, Bonn, Germany
	At the Electron Stretcher Facility ELSA of Bonn University, a longitudinal bunch-by-bunch feedback system is currently being installed in order to damp multibunch instabilities and to enable a future intensity upgrade of up to 200 mA. As a main component, a longitudinal kicker cavity was developed and manufactured. The kicker requires a bandwidth of 250~MHz taking into account the bunch spacing of 2 ns at ELSA. Existing designs used at other facilities were optimized in view of the considerably larger bunch lenght at ELSA. The choice of 1.125 GHz as a center frequency is a result of these considerations. With the resulting low quality factor, the design had to be optimized in order to maximize the shunt impedance. The longitudinal feedback is succesfully working with the prototype installed in the stretcher ring. The design and detailed simulations of the geometry are discussed and laboratory measurements are presented.

TUPC033	Verifying the Single Bunch Capability of the New Injector at ELSA*	1072
	S. Mey, O. Boldt, W. Hillert, N. Hofmann, F. Klarner, D. Krönung, A. Roth, M. Schedler ELSA, Bonn, Germany S. Aderhold DESY, Hamburg, Germany
	Funding: Funded by the DFG within the SFB / TR 16 and the Helmholtz Alliance HA 10¹ "Physics at the Terascale". In order to enhance the operating capabilities of the Bonn University Accelerator Facility, ELSA, a new injector is currently under commissioning. One of its main purpose is to allow a single pulse mode. The injector produces a single electron bunch with 1.5 A pulse current. Design and optimization of the injector have been performed with EGUN, PARMELA and numerical simulations based on the numerical integration of the paraxial equation. A 1 ns long pulse is produced by a thermionic electron source with 90 kV anode - cathode voltage, then compressed and pre-accelerated by a subsequent 500 MHz RF cavity and a four-cell travelling wave buncher. Finally, the bunch will be accelerated to 20 MeV by the main LINAC section. Measurements have been conducted concerning the resulting pulse length and pulse charge to confirm the predictions made by simulations and to investigate the efficiency of the injector system.

Paper

Title

Page

Commissioning of Multibunch Feedback Systems at the Fast Ramping Stretcher Ring ELSA

250

A. Roth, F. Frommberger, N. Heurich, W. Hillert, M. Schedler, R. Zimmermann
ELSA, Bonn, Germany

Funding: Supported by German Research Foundation through SFB/TR 16 and by Helmholtz Alliance through HA-10¹.
At the Electron Stretcher Facility ELSA of Bonn University, an external beam of either unpolarized or polarized electrons is supplied to hadron physics experiments. The ELSA stretcherring operates in the energy range of 1.2 to 3.5 GeV and achieves a duty cycle of up to 80% using a fast energy ramp of 4 GeV/s. Under these conditions, an increase of the internal beam current from an actual value of 20 mA up to 200 mA is planned. Such an upgrade is mainly limited by the excitation of multibunch instabilities. As one active counteraction, we have installed state-of-the-art bunch-by-bunch feedback systems for the longitudinal, as well as for both transverse planes. The detailed setup with all main components and first results of the commissioning of the systems will be presented. In particular, the performance of the longitudinal feedback with a stabilized synchrotron frequency during the fast energy ramp will be discussed.

MOPC078

Operation of Superconducting Cavities in a Fast Ramping Electron Storage Ring

253

A. Roth, W. Hillert
ELSA, Bonn, Germany

Funding: Supported by German Research Foundation through SFB/TR 16.
The achievable maximum energy of a medium-sized electron accelerator is mainly limited by the accelerating voltage. Using superconducting (sc) cavities, the energy limitation can be shifted considerably. However, the operation of sc multi-cell cavities in a fast ramping storage ring causes additional problems which were investigated at the 3.5 GeV Electron Stretcher Accelerator ELSA. We studied the use of two 500 MHz sc cavities providing the necessary resonator voltage of up to 14 MV and replacing the normal conducting cavities of PETRA type. A large cavity coupling factor is required, so that using the existing 250 kW klystron, an internal beam of 50 mA can be accelerated up to 5 GeV. In addition, a fast detuning of the resonance frequency of the cavities must be implemented during beam injection and the energy ramp of 4 GeV/s. An appropriate 500 MHz structure is given by a five-cell cavity constructed for the JAERI-FEL-LINAC. Based on this geometry, HOM have been calculated from a numerical simulation. Since all monopole and a larger number of dipole HOM are well above the multibunch instabilities threshold, further studies about beam instabilities damping are essential.

MOPO003

A Broadband RF Stripline Kicker for Damping Transversal Multibunch Instabilities

481

M. Schedler, D. Heiliger, W. Hillert, A. Roth
ELSA, Bonn, Germany

When operating an RF feedback system, being able to reliably act upon every single bunch is a necessity. By employing a broadband RF stripline kicker, any bunch displacement can be corrected for. In a 500 MHz accelerator, the decay time of the electromagnetic field inside the kicker has to be less than 2 ns in order to avoid the following bunch to be affected. By designing the kicker as an RF coax device matched to the line impedance of the power cables, perturbing reflected signals are avoided. Additionally, the kicking strength and thus the shunt impedance should be maximized over the full spectrum from DC to 250 MHz. The kicker design has been optimized to meet the above requirements by relying on CST Microwave Studio simulations. Their results and first measurements are presented.

MOPO004

A Longitudinal Kicker Cavity for a Bunch-by-bunch Feedback System at ELSA

484

N. Heurich, W. Hillert, A. Roth, R. Zimmermann
ELSA, Bonn, Germany

At the Electron Stretcher Facility ELSA of Bonn University, a longitudinal bunch-by-bunch feedback system is currently being installed in order to damp multibunch instabilities and to enable a future intensity upgrade of up to 200 mA. As a main component, a longitudinal kicker cavity was developed and manufactured. The kicker requires a bandwidth of 250~MHz taking into account the bunch spacing of 2 ns at ELSA. Existing designs used at other facilities were optimized in view of the considerably larger bunch lenght at ELSA. The choice of 1.125 GHz as a center frequency is a result of these considerations. With the resulting low quality factor, the design had to be optimized in order to maximize the shunt impedance. The longitudinal feedback is succesfully working with the prototype installed in the stretcher ring. The design and detailed simulations of the geometry are discussed and laboratory measurements are presented.

TUPC033

Verifying the Single Bunch Capability of the New Injector at ELSA*

1072

S. Mey, O. Boldt, W. Hillert, N. Hofmann, F. Klarner, D. Krönung, A. Roth, M. Schedler
ELSA, Bonn, Germany
S. Aderhold
DESY, Hamburg, Germany

Funding: Funded by the DFG within the SFB / TR 16 and the Helmholtz Alliance HA 10¹ "Physics at the Terascale".
In order to enhance the operating capabilities of the Bonn University Accelerator Facility, ELSA, a new injector is currently under commissioning. One of its main purpose is to allow a single pulse mode. The injector produces a single electron bunch with 1.5 A pulse current. Design and optimization of the injector have been performed with EGUN, PARMELA and numerical simulations based on the numerical integration of the paraxial equation. A 1 ns long pulse is produced by a thermionic electron source with 90 kV anode - cathode voltage, then compressed and pre-accelerated by a subsequent 500 MHz RF cavity and a four-cell travelling wave buncher. Finally, the bunch will be accelerated to 20 MeV by the main LINAC section. Measurements have been conducted concerning the resulting pulse length and pulse charge to confirm the predictions made by simulations and to investigate the efficiency of the injector system.