IPAC2011 - List of Authors (Müller, G.J.)

Paper	Title	Page
TUPZ001	90 m Optics Commissioning	1795
	S. Cavalier LAL, Orsay, France H. Burkhardt, M. Fitterer, G.J. Müller, S. Redaelli, R. Tomás, G. Vanbavinckhove, J. Wenninger CERN, Geneva, Switzerland
	Special β* = 90 m optics have been developed for the two very high luminosity insertions of the LHC, as a first step towards to allow for very low angle precision measurements of the proton-proton collisions in the LHC. These optics were developed to be compatible with the standard LHC injection and ramp optics. The target value of β* = 90 m is reached by an un-squeeze from the injection β* = 11 m. We describe the implementation of this optics in the LHC and the first experience in the commissioning of these optics.

TUPZ006	Aperture Determination in the LHC Based on an Emittance Blowup Technique with Collimator Position Scan	1810
	R.W. Assmann, R. Bruce, M. Giovannozzi, G.J. Müller, S. Redaelli, F. Schmidt, R. Tomás, J. Wenninger, D. Wollmann CERN, Geneva, Switzerland M. Alabau IFIC, Valencia, Spain
	A new method to determine the LHC aperture was proposed. The new component is a collimator scan technique that refers the globally measured aperture limit to the shadow of the primary collimator, expressed in σs of rms beam size. As a by-product the BLM response to beam loss is quantified. The method is described and LHC measurement results are presented.

TUPZ030	Simulation of Linear Beam Parameters to Minimize the Duration of the Squeeze at the LHC	1873
	X. Buffat EPFL, Lausanne, Switzerland G.J. Müller, S. Redaelli, M. Strzelczyk CERN, Geneva, Switzerland
	The betatron squeeze allows to increase the luminosity of a collider by reducing the β function at the interaction points. This operation has shown to be very critical in previous colliders. In this state of mind, the squeezing was performed extremely safely during the first year of operation of the Large Hadron Collider, at the expense of the duration of the process. As the turnaround time is a relevant parameter for the integrated luminosity, a squeeze of shorter duration is proposed for 2011 and further. MadX simulation of linear beam parameters based on settings extracted from the LHC control system are used to justify the proposal. Further optimization of the squeeze setting generation is also discussed.

WEPC120	Status of JMAD, the JAVA-API for MADX	2292
	K. Fuchsberger, X. Buffat, Y.I. Levinsen, G.J. Müller CERN, Geneva, Switzerland
	MADX (Methodical Accelerator Design) is the de-facto standard software for modeling accelerator lattices at CERN. This feature-rich software package is implemented and still maintained in the programming languages C and FORTRAN. Nevertheless the controls environment of modern accelerators at CERN, e.g., of the LHC, is dominated by JAVA applications. A lot of these applications, for example, for lattice measurement and fitting, require a close interaction with the numerical models, which are all defined by the use of the proprietary MADX scripting language. To close this gap an API to MADX for the JAVA programming language (JMAD) was developed. JMAD was first presented to the public about one year ago. In the meantime, a number of improvements were done, and additional MADX features (e.g., tracking) were made available for JAVA applications. Additionally, the graphical user interface was improved, and the first release as open source software is in reach. This paper describes the current status and some new features of the project, as well as some usage examples.

Paper

Title

Page

90 m Optics Commissioning

1795

S. Cavalier
LAL, Orsay, France
H. Burkhardt, M. Fitterer, G.J. Müller, S. Redaelli, R. Tomás, G. Vanbavinckhove, J. Wenninger
CERN, Geneva, Switzerland

Special β* = 90 m optics have been developed for the two very high luminosity insertions of the LHC, as a first step towards to allow for very low angle precision measurements of the proton-proton collisions in the LHC. These optics were developed to be compatible with the standard LHC injection and ramp optics. The target value of β* = 90 m is reached by an un-squeeze from the injection β* = 11 m. We describe the implementation of this optics in the LHC and the first experience in the commissioning of these optics.

TUPZ006

Aperture Determination in the LHC Based on an Emittance Blowup Technique with Collimator Position Scan

1810

R.W. Assmann, R. Bruce, M. Giovannozzi, G.J. Müller, S. Redaelli, F. Schmidt, R. Tomás, J. Wenninger, D. Wollmann
CERN, Geneva, Switzerland
M. Alabau
IFIC, Valencia, Spain

A new method to determine the LHC aperture was proposed. The new component is a collimator scan technique that refers the globally measured aperture limit to the shadow of the primary collimator, expressed in σs of rms beam size. As a by-product the BLM response to beam loss is quantified. The method is described and LHC measurement results are presented.

TUPZ030

Simulation of Linear Beam Parameters to Minimize the Duration of the Squeeze at the LHC

1873

X. Buffat
EPFL, Lausanne, Switzerland
G.J. Müller, S. Redaelli, M. Strzelczyk
CERN, Geneva, Switzerland

The betatron squeeze allows to increase the luminosity of a collider by reducing the β function at the interaction points. This operation has shown to be very critical in previous colliders. In this state of mind, the squeezing was performed extremely safely during the first year of operation of the Large Hadron Collider, at the expense of the duration of the process. As the turnaround time is a relevant parameter for the integrated luminosity, a squeeze of shorter duration is proposed for 2011 and further. MadX simulation of linear beam parameters based on settings extracted from the LHC control system are used to justify the proposal. Further optimization of the squeeze setting generation is also discussed.

WEPC120

Status of JMAD, the JAVA-API for MADX

2292

K. Fuchsberger, X. Buffat, Y.I. Levinsen, G.J. Müller
CERN, Geneva, Switzerland

MADX (Methodical Accelerator Design) is the de-facto standard software for modeling accelerator lattices at CERN. This feature-rich software package is implemented and still maintained in the programming languages C and FORTRAN. Nevertheless the controls environment of modern accelerators at CERN, e.g., of the LHC, is dominated by JAVA applications. A lot of these applications, for example, for lattice measurement and fitting, require a close interaction with the numerical models, which are all defined by the use of the proprietary MADX scripting language. To close this gap an API to MADX for the JAVA programming language (JMAD) was developed. JMAD was first presented to the public about one year ago. In the meantime, a number of improvements were done, and additional MADX features (e.g., tracking) were made available for JAVA applications. Additionally, the graphical user interface was improved, and the first release as open source software is in reach. This paper describes the current status and some new features of the project, as well as some usage examples.