IPAC2011 - List of Authors (Minamikawa, T.)

Paper

Title

Page

Acceleration of High Intensity Proton Beams in the J-PARC Synchrotrons

2502

M. Yoshii
KEK/JAEA, Ibaraki-Ken, Japan
E. Ezura, K. Hara, K. Hasegawa, C. Ohmori, K. Takata, M. Toda
KEK, Tokai, Ibaraki, Japan
T. Minamikawa
University of Fukui, Fukui, Japan
M. Nomura, A. Schnase, T. Shimada, F. Tamura, M. Yamamoto
JAEA/J-PARC, Tokai-mura, Japan

The J-PARC accelerator complex consists of the linac, the 3GeV rapid cycling synchrotron (RCS) and the 50GeV main synchrotron (MR). These synchrotrons are the first MW-class proton accelerators which employ the high electric field gradient magnetic alloy (MA) loaded RF cavities. The beam commissioning was started in October 2007 for RCS and in May 2008 for MR. High intensity beam operation studies and user runs have been performed, while carefully controlling and minimizing the beam loss. The cycle to cycle beam operation is reproducible and quite stable, because of the stable linac beam energy and the reproducible bending field in both synchrotrons. The MA loaded RF systems and the full digital LLRF also guarantee the stable longitudinal particle motion and precise beam transfer synchronization from RCS to the MLF user facility as well as to the MR. A high intensity proton beam of 2.5·10¹³ ppp is accelerated in RCS. And in MR, a beam intensity up to ~100 Tera ppp was obtained.　We summarize the RF systems and the longitudinal parameters in both rings.

THOBB02

High Gradient Magnetic Alloy Cavities for J-PARC Upgrade

2885

C. Ohmori, O. Araoka, E. Ezura, K. Hara, K. Hasegawa, A. Koda, Y. Makida, Y. Miyake, R. Muto, K. Nishiyama, T. Ogitsu, H. Ohhata, K. Shimomura, A. Takagi, K. Takata, K.H. Tanaka, M. Toda, M. Yoshii
KEK, Tokai, Ibaraki, Japan
T. Minamikawa
University of Fukui, Fukui, Japan
M. Nomura, A. Schnase, T. Shimada, F. Tamura, M. Yamamoto
JAEA/J-PARC, Tokai-mura, Japan

Magnetic alloy cavities are used for both MR and RCS synchrotrons. Both cavity systems operate successfully and they generate a higher voltage than could be achieved by an ordinary ferrite cavity system. For the future upgrade of J-PARC, a higher RF voltage is needed. A new RF cavity system using the material, FT3L, is designed to achieve this higher field gradient. A large production system using an old cyclotron magnet was constructed to anneal 85-cm size FT3L cores in the J-PARC Hadron Experiment Hall. The muSR (Muon Spin Rotation/Relaxation/Resonance) Experiments were also carried out to study the magnetic alloy. The status of development on the J-PARC site and a new RF system design will be reported.

Slides THOBB02 [2.729 MB]

Paper	Title	Page
WEPS010	Acceleration of High Intensity Proton Beams in the J-PARC Synchrotrons	2502
	M. Yoshii KEK/JAEA, Ibaraki-Ken, Japan E. Ezura, K. Hara, K. Hasegawa, C. Ohmori, K. Takata, M. Toda KEK, Tokai, Ibaraki, Japan T. Minamikawa University of Fukui, Fukui, Japan M. Nomura, A. Schnase, T. Shimada, F. Tamura, M. Yamamoto JAEA/J-PARC, Tokai-mura, Japan
	The J-PARC accelerator complex consists of the linac, the 3GeV rapid cycling synchrotron (RCS) and the 50GeV main synchrotron (MR). These synchrotrons are the first MW-class proton accelerators which employ the high electric field gradient magnetic alloy (MA) loaded RF cavities. The beam commissioning was started in October 2007 for RCS and in May 2008 for MR. High intensity beam operation studies and user runs have been performed, while carefully controlling and minimizing the beam loss. The cycle to cycle beam operation is reproducible and quite stable, because of the stable linac beam energy and the reproducible bending field in both synchrotrons. The MA loaded RF systems and the full digital LLRF also guarantee the stable longitudinal particle motion and precise beam transfer synchronization from RCS to the MLF user facility as well as to the MR. A high intensity proton beam of 2.5·10¹³ ppp is accelerated in RCS. And in MR, a beam intensity up to ~100 Tera ppp was obtained.　We summarize the RF systems and the longitudinal parameters in both rings.

THOBB02	High Gradient Magnetic Alloy Cavities for J-PARC Upgrade	2885
	C. Ohmori, O. Araoka, E. Ezura, K. Hara, K. Hasegawa, A. Koda, Y. Makida, Y. Miyake, R. Muto, K. Nishiyama, T. Ogitsu, H. Ohhata, K. Shimomura, A. Takagi, K. Takata, K.H. Tanaka, M. Toda, M. Yoshii KEK, Tokai, Ibaraki, Japan T. Minamikawa University of Fukui, Fukui, Japan M. Nomura, A. Schnase, T. Shimada, F. Tamura, M. Yamamoto JAEA/J-PARC, Tokai-mura, Japan
	Magnetic alloy cavities are used for both MR and RCS synchrotrons. Both cavity systems operate successfully and they generate a higher voltage than could be achieved by an ordinary ferrite cavity system. For the future upgrade of J-PARC, a higher RF voltage is needed. A new RF cavity system using the material, FT3L, is designed to achieve this higher field gradient. A large production system using an old cyclotron magnet was constructed to anneal 85-cm size FT3L cores in the J-PARC Hadron Experiment Hall. The muSR (Muon Spin Rotation/Relaxation/Resonance) Experiments were also carried out to study the magnetic alloy. The status of development on the J-PARC site and a new RF system design will be reported.
	Slides THOBB02 [2.729 MB]