IPAC2011 - List of Authors (Losito, R.)

Paper	Title	Page
MOPC150	High Charge PHIN Photo Injector at CERN with Fast Phase Switching within the Bunch Train for Beam Combination	430
	M. Divall Csatari, A. Andersson, B. Bolzon, E. Bravin, E. Chevallay, A.E. Dabrowski, S. Döbert, V. Fedosseev, C. Heßler, T. Lefèvre, S. Livesley, R. Losito, O. Mete, M. Olvegård, M. Petrarca, A. Rabiller CERN, Geneva, Switzerland A. Drozdy BUTE, Budapest, Hungary D. Egger EPFL, Lausanne, Switzerland
	The high charge PHIN photo-injector was developed within the frame of the European CARE program to provide an alternative to the drive beam thermionic gun in CTF3 (CLIC Test Facility) at CERN. In PHIN 1908 bunches are delivered with bunch spacing of 1.5 GHz and 2.33 nC charge per bunch. Furthermore the drive beam generated by CTF3 requires several fast 180 deg phase-shifts with respect to the 1.5 GHz bunch repetition frequency in order to allow the beam combination scheme developed at CTF3. A total of 8 sub-trains, each 140 ns long and shifted in phase with respect to each other, have to be produced with very high phase and amplitude stability. A novel fiber modulator based phase-switching technique developed on the laser system provides this phase-shift between two consecutive pulses much faster and cleaner than the base line scheme, where a thermionic electron gun and sub-harmonic bunching are used. The paper describes the fiber-based switching system and the measurements verifying the scheme. Stability measurements are presented for the phase-coded system. The paper also discusses the latest 8nC charge production and cathode life-time studies on Cs2Te.

TUPS039	Reduction of Magnetic Interference on the Position Sensors of the LHC Collimators	1623
	A. Masi, M. Lamberti, R. Losito, M. Martino CERN, Geneva, Switzerland
	The jaws of the LHC collimators have to be positioned with respect to the beam with an accuracy of 20 μm. On some collimators, installed in the LHC transfer lines from SPS, huge reading errors of several tens of micrometers have been observed on the Linear Variable Differential Transformer (LVDT) positioning sensors in synchronization with the variable magnetic field produced by the feed cables of the pulsed resistive dipoles of the transfer line. In this paper we introduce and describe in detail the problem, the model developed using FLUXTM for the simulation of the magnetic flux density generated by the current cables in the complex environment of an LHC transfer line, and the magnetic shielding we designed and implemented. Finally, we compare the results of simulations with experimental measurements taken during on-line pulsed magnets test campaigns.

TUPS040	Driving the LHC Collimators' Stepping Motors over 1 km with High Accuracy avoiding EMI Effects	1626
	A. Masi, G. Conte, R. Losito, M. Martino CERN, Geneva, Switzerland
	The LHC collimators are exposed to very high levels of radiation, which means that the power drivers must be installed far from the stepping motors that they drive. Due to the geometry of the underground installations, the distances can be up to 1 km. The long cables that connect the drivers to the motors behave as transmission lines modifying dramatically the impedance seen by the drivers and consequently jeopardizing the control performance of Pulse Width Modulation (PWM) drivers. In this paper we address this problem, provide an analytical model of the driver-cable-motor system and describe the analog solution we have developed to improve the performance of a typical off the shelf driver. Finally we characterize the improvement of the performances with measurements of positioning repeatability and show that electromagnetic emissions from the long cables are drastically reduced, making the use of stepping motors compatible with extremely sensitive instrumentation such as the LHC Beam Loss Monitors (BLM).

Paper

Title

Page

High Charge PHIN Photo Injector at CERN with Fast Phase Switching within the Bunch Train for Beam Combination

430

M. Divall Csatari, A. Andersson, B. Bolzon, E. Bravin, E. Chevallay, A.E. Dabrowski, S. Döbert, V. Fedosseev, C. Heßler, T. Lefèvre, S. Livesley, R. Losito, O. Mete, M. Olvegård, M. Petrarca, A. Rabiller
CERN, Geneva, Switzerland
A. Drozdy
BUTE, Budapest, Hungary
D. Egger
EPFL, Lausanne, Switzerland

The high charge PHIN photo-injector was developed within the frame of the European CARE program to provide an alternative to the drive beam thermionic gun in CTF3 (CLIC Test Facility) at CERN. In PHIN 1908 bunches are delivered with bunch spacing of 1.5 GHz and 2.33 nC charge per bunch. Furthermore the drive beam generated by CTF3 requires several fast 180 deg phase-shifts with respect to the 1.5 GHz bunch repetition frequency in order to allow the beam combination scheme developed at CTF3. A total of 8 sub-trains, each 140 ns long and shifted in phase with respect to each other, have to be produced with very high phase and amplitude stability. A novel fiber modulator based phase-switching technique developed on the laser system provides this phase-shift between two consecutive pulses much faster and cleaner than the base line scheme, where a thermionic electron gun and sub-harmonic bunching are used. The paper describes the fiber-based switching system and the measurements verifying the scheme. Stability measurements are presented for the phase-coded system. The paper also discusses the latest 8nC charge production and cathode life-time studies on Cs2Te.

TUPS039

Reduction of Magnetic Interference on the Position Sensors of the LHC Collimators

1623

A. Masi, M. Lamberti, R. Losito, M. Martino
CERN, Geneva, Switzerland

The jaws of the LHC collimators have to be positioned with respect to the beam with an accuracy of 20 μm. On some collimators, installed in the LHC transfer lines from SPS, huge reading errors of several tens of micrometers have been observed on the Linear Variable Differential Transformer (LVDT) positioning sensors in synchronization with the variable magnetic field produced by the feed cables of the pulsed resistive dipoles of the transfer line. In this paper we introduce and describe in detail the problem, the model developed using FLUXTM for the simulation of the magnetic flux density generated by the current cables in the complex environment of an LHC transfer line, and the magnetic shielding we designed and implemented. Finally, we compare the results of simulations with experimental measurements taken during on-line pulsed magnets test campaigns.

TUPS040

Driving the LHC Collimators' Stepping Motors over 1 km with High Accuracy avoiding EMI Effects

1626

A. Masi, G. Conte, R. Losito, M. Martino
CERN, Geneva, Switzerland

The LHC collimators are exposed to very high levels of radiation, which means that the power drivers must be installed far from the stepping motors that they drive. Due to the geometry of the underground installations, the distances can be up to 1 km. The long cables that connect the drivers to the motors behave as transmission lines modifying dramatically the impedance seen by the drivers and consequently jeopardizing the control performance of Pulse Width Modulation (PWM) drivers. In this paper we address this problem, provide an analytical model of the driver-cable-motor system and describe the analog solution we have developed to improve the performance of a typical off the shelf driver. Finally we characterize the improvement of the performances with measurements of positioning repeatability and show that electromagnetic emissions from the long cables are drastically reduced, making the use of stepping motors compatible with extremely sensitive instrumentation such as the LHC Beam Loss Monitors (BLM).