IPAC2011 - List of Authors (Benabderrahmane, C.)

Paper	Title	Page
THPC149	Development of PrFeB Cryogenic Undulator (CPMU) at SOLEIL	3233
	C. Benabderrahmane, P. Berteaud, N. Béchu, L. Chapuis, M.-E. Couprie, J.P. Daguerre, J.-M. Filhol, C. Herbeaux, A. Lestrade, M. Louvet, J.L. Marlats, K. Tavakoli, M. Valléau, D. Zerbib SOLEIL, Gif-sur-Yvette, France
	A R&D programme for the construction of a 2 m long 18 mm period CPMU is under progress at SOLEIL. The cryogenic undulator will provide photons in the region of 1.4 to 30 keV. It will be installed in the next few months on the long straight section (SDL13) of the storage ring, and could be used later on to produce photons for the NANOSCOPIUM beamline. The use of PrFeB which features a 1.35 T remanence (Br) at room temperature enables to increase the peak magnetic field at 5.5 mm minimum gap, from 1.04 T at room temperature to 1.15 T at a cryogenic temperature of 77 K. Praseodymium was chosen instead of Neodymium magnetic material, because it is more resistant against the appearance of the Spin Reorientation Transition. Different corrections were performed first at room temperature to adjust the phase error, the electron trajectory and to reduce the multipolar components. The mounting inside the vacuum chamber enables the fitting of a dedicated magnetic measurement bench to check the magnetic performance of the undulator at low temperature. The results of the magnetic measurements at low temperature and the comparison with the measurement at room temperature are reported.

THPC150	Review of Insertion Device Dedicated to HIgh Energy Photons at SOLEIL	3236
	O. Marcouillé, C. Benabderrahmane, P. Berteaud, F. Briquez, L. Chapuis, M.-E. Couprie, T.K. El Ajjouri, F. Marteau, M. Valléau, J. Vétéran SOLEIL, Gif-sur-Yvette, France
	Producing high energy photons between 10 keV and 70 keV is a challenging topic in a medium energy storage ring. It requires up-to-date measurement techniques and specific Insertion Device (ID) technologies to produce high magnetic fields and short periods. SOLEIL (2.75 GeV) has designed and built eight conventional in-vacuum hybrid undulators operating at high radiation harmonics and also one small gap multipole wiggler to produce high magnetic field. The construction has been progressively improved by the choice of new magnetic materials of better quality and higher magnetization, additional correction techniques and mechanical changes. A 2-m long full scale cryogenic undulator made of PrFeB and vanadium permendur has been built, measured, corrected and is to be tested on the beam. An additional wiggler dedicated for Slicing experiments has been designed. The required magnetic field is high enough to also consider the ID as a good candidate for the production of hard X-ray photons. This paper presents the ID dedicated for the high energy photons and their spectral performances.

THPC152	Measurements of SOLEIL Insertion Devices using Pulsed Wire Method	3242
	M. Valléau, C. Benabderrahmane, M.-E. Couprie, O. Marcouillé, F. Marteau, J. Vétéran SOLEIL, Gif-sur-Yvette, France
	SOLEIL permanent magnets insertion devices are usually measured with a Hall probe in order to evaluate the electron angular deflexion, their deviation and the optical phase error, a figure of merit related to the quality of the insertion device radiation. A pulsed wire bench is developed at SOLEIL for reducing the measurement time of an undulator and for providing a measurement method without lateral access. A current pulse injected in a stretched wire inside the magnetic field area generates acoustic wave. The wire motion is detected by optical sensors whose signals are proportional to the local integral value. The signal-to-noise ratio of this method is often reduced due to several effects such as electronic noise, external and wire vibrations. However, following some hardware optimization it was possible to increase it up to almost 26 dB, making the method accurate and reproducible in order to realize efficient corrections. Measurements of first and second integral performed with Pulse wire, with Hall probe and with the electron beam are compared on three different types of insertions: an U18 in-vacuum cryogenic undulator, a HU60 APPLE-II undulator and a WSV50 in-vacuum wiggler.

Paper

Title

Page

Development of PrFeB Cryogenic Undulator (CPMU) at SOLEIL

3233

C. Benabderrahmane, P. Berteaud, N. Béchu, L. Chapuis, M.-E. Couprie, J.P. Daguerre, J.-M. Filhol, C. Herbeaux, A. Lestrade, M. Louvet, J.L. Marlats, K. Tavakoli, M. Valléau, D. Zerbib
SOLEIL, Gif-sur-Yvette, France

A R&D programme for the construction of a 2 m long 18 mm period CPMU is under progress at SOLEIL. The cryogenic undulator will provide photons in the region of 1.4 to 30 keV. It will be installed in the next few months on the long straight section (SDL13) of the storage ring, and could be used later on to produce photons for the NANOSCOPIUM beamline. The use of PrFeB which features a 1.35 T remanence (Br) at room temperature enables to increase the peak magnetic field at 5.5 mm minimum gap, from 1.04 T at room temperature to 1.15 T at a cryogenic temperature of 77 K. Praseodymium was chosen instead of Neodymium magnetic material, because it is more resistant against the appearance of the Spin Reorientation Transition. Different corrections were performed first at room temperature to adjust the phase error, the electron trajectory and to reduce the multipolar components. The mounting inside the vacuum chamber enables the fitting of a dedicated magnetic measurement bench to check the magnetic performance of the undulator at low temperature. The results of the magnetic measurements at low temperature and the comparison with the measurement at room temperature are reported.

THPC150

Review of Insertion Device Dedicated to HIgh Energy Photons at SOLEIL

3236

O. Marcouillé, C. Benabderrahmane, P. Berteaud, F. Briquez, L. Chapuis, M.-E. Couprie, T.K. El Ajjouri, F. Marteau, M. Valléau, J. Vétéran
SOLEIL, Gif-sur-Yvette, France

Producing high energy photons between 10 keV and 70 keV is a challenging topic in a medium energy storage ring. It requires up-to-date measurement techniques and specific Insertion Device (ID) technologies to produce high magnetic fields and short periods. SOLEIL (2.75 GeV) has designed and built eight conventional in-vacuum hybrid undulators operating at high radiation harmonics and also one small gap multipole wiggler to produce high magnetic field. The construction has been progressively improved by the choice of new magnetic materials of better quality and higher magnetization, additional correction techniques and mechanical changes. A 2-m long full scale cryogenic undulator made of PrFeB and vanadium permendur has been built, measured, corrected and is to be tested on the beam. An additional wiggler dedicated for Slicing experiments has been designed. The required magnetic field is high enough to also consider the ID as a good candidate for the production of hard X-ray photons. This paper presents the ID dedicated for the high energy photons and their spectral performances.

THPC152

Measurements of SOLEIL Insertion Devices using Pulsed Wire Method

3242

M. Valléau, C. Benabderrahmane, M.-E. Couprie, O. Marcouillé, F. Marteau, J. Vétéran
SOLEIL, Gif-sur-Yvette, France

SOLEIL permanent magnets insertion devices are usually measured with a Hall probe in order to evaluate the electron angular deflexion, their deviation and the optical phase error, a figure of merit related to the quality of the insertion device radiation. A pulsed wire bench is developed at SOLEIL for reducing the measurement time of an undulator and for providing a measurement method without lateral access. A current pulse injected in a stretched wire inside the magnetic field area generates acoustic wave. The wire motion is detected by optical sensors whose signals are proportional to the local integral value. The signal-to-noise ratio of this method is often reduced due to several effects such as electronic noise, external and wire vibrations. However, following some hardware optimization it was possible to increase it up to almost 26 dB, making the method accurate and reproducible in order to realize efficient corrections. Measurements of first and second integral performed with Pulse wire, with Hall probe and with the electron beam are compared on three different types of insertions: an U18 in-vacuum cryogenic undulator, a HU60 APPLE-II undulator and a WSV50 in-vacuum wiggler.