BNL, Upton, Long Island, New York, USA
AES, Medford, NY, USA
The 703 MHz superconducting gun for BNL ERL prototype was tested at JLab with and without choke-joint and cathode stalk. Without choke-joint and cathode stalk, the gradient reached 25MV/m with Q0~6·109. The gun cathode insertion port is equipped with a choke joint with triangular grooves for multipacting suppression. We carried out tests with choke-joint and cathode stalk. The test results show that there are at least two barriers at about 5MV/m and 3.5 MV/m. We considered several possibilities and finally found that the limitation was because the triangular grooves were rounded after BCP, which caused strong multipacting in the choke-joint. This paper presents the primary test result of test results of the gun and discusses the multipacting analysis in the choke-joint. It also suggests possible solutions for the gun and multipacting suppressing for a similar structure.
BNL, Upton, Long Island, New York, USA
Damping higher order modes (HOMs) significantly to avoid beam instability is a challenge for the high current Energy Recovery Linac-based eRHIC at BNL. To avoid the overheating effect and high tuning sensitivity, current, a new band-stop HOM coupler is being designed at BNL. The new HOM coupler has a bandwidth of tens of MHz to reject the fundamental mode, which will avoid overheating due to fundamental frequency shifting because of cooling down. In addition, the S21 parameter of the band-pass filter is nearly flat from first higher order mode to 5 times the fundamental frequency. The simulation results showed that the new couplers effectively damp HOMs for the eRHIC cavity with enlarged beam tube diameter and two 120° HOM couplers at each side of cavity. This paper presents the design of HOM coupler, HOM damping capacity for eRHIC cavity and prototype test results.
BNL, Upton, Long Island, New York, USA
AES, Medford, NY, USA
The 703MHz superconducting gun will have 2 fundamental power couplers (FPCs). Each FPC will deliver up to 500kW of RF power. In order to prepare the couplers for high power RF service and process multipacting, the FPCs should be conditioned before they are installed in the gun. A conditioning cart based test stand, which includes a vacuum pumping system, controllable bake-out system, diagnostics, interlocks and data log system has been designed, constructed and commissioned by collaboration of BNL and AES. This paper presents FPC conditioning cart systems and summarizes the conditioning process and results.
AES, Medford, NY, USA
Stony Brook University, Stony Brook, USA
BNL, Upton, Long Island, New York, USA
Advanced Energy Systems, Inc. is under contract to Stony Brook University to design and build a 704 MHz, high current, Superconducting RF (SRF) five cell cavity to be tested at Brookhaven National Laboratory. This cavity is being designed to the requirements of the SPL at CERN while also considering operation with electrons for a potential RHIC upgrade at Brookhaven. The β=1 cavity shape, developed by Brookhaven, is designed to accelerate 40 mA of protons at an accelerating field of 25 MV/m with a Q0 > 8·109 at 2K while providing excellent HOM damping for potential electron applications. 10-CFR-851 states that all pressurized vessels on DOE sites must conform to applicable national consensus codes or, if they do not apply, provide an equivalent level of safety and protection. This paper presents how the 2007 ASME Boiler and Pressure Vessel Code Section VIII, Division 2 requirements can be used to satisfy the DOE pressure safety requirements for a non-code specified material (niobium) pressure vessel.
BNL, Upton, Long Island, New York, USA
In order to meet the requirements of high average current accelerators, such as the Superconducting Proton Linac (SPL) at CERN and the electron–ion collider (eRHIC) at BNL, a high current 5-cell SRF cavity, called BNL3 cavity, was designed. The optimization process aimed at maximizing the R/Q of the fundamental mode and the geometry factor G under an acceptable RF field level of Bpeak/Eacc or Epeak/Eacc. In addition, a pivotal consideration for the high current accelerators is efficient damping of dangerous higher-order modes (HOM) to avoid inducing emittance degradation, cryogenic loading or beam-breakup (BBU). To transport the HOMs out of the cavity, the BNL3 cavity employs a larger beam pipe, allowing the propagation of HOMs but not the fundamental mode. Moreover, concerning the BBU effect, the BNL3 cavity is aimed at low (R/Q)Qext for dangerous modes, including dipole modes and quadrupole modes. This paper presents the design of the BNL3 cavity, including the optimization for the fundamental mode, and the BBU limitation for dipole and quadrupole modes. The BBU simulation results show that the designed cavity is qualified for high-current, multi-pass machines such as eRHIC.
BNL, Upton, Long Island, New York, USA
FRIB, East Lansing, Michigan, USA
MIT, Middleton, Massachusetts, USA
We present the design of future high-energy high-luminosity electron-hadron collider at RHIC called eRHIC. We plan on adding 20 (potentially 30) GeV energy recovery linacs to accelerate and to collide polarized and unpolarized electrons with hadrons in RHIC. The center-of-mass energy of eRHIC will range from 30 to 200 GeV. The luminosity exceeding 1034 cm-2 s-1 can be achieved in eRHIC using the low-beta interaction region with a 10 mrad crab crossing. We report on the progress of important eRHIC R&D such as the high-current polarized electron source, the coherent electron cooling and the compact magnets for recirculating passes. A natural staging scenario of step-by-step increases of the electron beam energy by builiding-up of eRHIC's SRF linacs and a potential of adding polarized positrons are also presented.
BNL, Upton, Long Island, New York, USA
JLAB, Newport News, Virginia, USA
AES, Medford, NY, USA
The Brookhaven National Laboratory (BNL) 5-cell, 703 MHz superconducting RF accelerating cavity has been installed in the high-current energy recovery linac (ERL) experiment. This experiment will function as a proving ground for the development of high-current machines in general and is particularly targeted at beam development for an electron-ion collider (eRHIC). The cavity performed well in vertical tests, demonstrating gradients of 20 MV/m and a Q0 of 1010. Here we will present its performance in the horizontal tests, and discuss technical issues involved in its implementation in the ERL.
BNL, Upton, Long Island, New York, USA
USTC/NSRL, Hefei, Anhui, People's Republic of China
FEL/Duke University, Durham, North Carolina, USA