2011 Particle Accelerator Conference - List of Authors (Mi, C.)

Paper	Title	Page
MOP248	Automating Power Supply Checkout	577
	J.S. Laster, D. Bruno, T. D'Ottavio, J. Drozd, G.J. Marr, C. Mi BNL, Upton, Long Island, New York, USA
	Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy. Power Supply checkout is a necessary, pre-beam, time-critical function. At odds are the desire to decrease the amount of time to perform the checkout while at the same time maximizing the number and types of checks that can be performed and analyzing the results quickly (in case any problems exist that must be addressed). Controls and Power Supply Group personnel have worked together to develop tools to accomplish these goals. Power Supply checkouts are now accomplished in a time-frame of hours rather than days, reducing the number of person-hours needed to accomplish the checkout and making the system available more quickly for beam development.

TUP225	Overview of Recent Studies and Modifications Being Made to RHIC to Mitigate the Effects of a Potential Failure to the Helium Distribution System	1241
	J.E. Tuozzolo, D. Bruno, A. Di Lieto, G. Heppner, R. Karol, E.T. Lessard, C.J. Liaw, G.T. McIntyre, C. Mi, J. Reich, J. Sandberg, S.K. Seberg, L. Smart, T.N. Tallerico, R. Than, C. Theisen, R.J. Todd, R. Zapasek BNL, Upton, Long Island, New York, USA
	Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy. In order to cool the superconducting magnets in RHIC, its helium refrigerator distributes 4.5 K helium throughout the tunnel via a series of distribution and return lines. The worst case for failure would be a release from the magnet distribution line, which operates at 3.5 to 4.5 atmospheres and contains the energized magnet bus. Should the bus insulation system fail or an electrical connection open, there is the potential for releasing up to 70 MJoules of stored energy. Studies were done to determine release rate of the helium and the resultant reduction in O2 concentration in the RHIC tunnel and service buildings. Equipment and components were also reviewed for reliability and the effects of 10 years of operations. Modifications were made to reduce the likelihood of failure and to reduce the amount of helium gas that could be released into tunnels and service buildings while personnel are present. This paper describes the issues reviewed, the steps taken, and remaining work to be done to reduce the hazards.

THP060	RHIC 12x150A Current Lead Temperature Controller: Design and Implementation	2238
	C. Mi, D. Bruno, N.M. Day, A. Di Lieto, G. Ganetis, K. Hamdi, G. Heppner, J.P. Jamilkowski, W. Louie, J. Sandberg, S.K. Seberg, C. Sirio, J.E. Tuozzolo, K.L. Unger BNL, Upton, Long Island, New York, USA
	Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy There are 60 12×150A current leads distributed in 6 RHIC service buildings; each current lead delivers power supply current from room temperature to cryogenic temperature in RHIC. Due to the humid environment, condensation frequently occurs and ice was quickly formed during operation, especially during an extensive storage period. This condition generated warnings and alarms that personal had to respond to, in order to provide temporary solutions, to keep the machine operational. A temperature control system was designed to avoid such occasions. We will discuss design, implementation and some results of this design in this paper.

Paper

Title

Page

Automating Power Supply Checkout

577

J.S. Laster, D. Bruno, T. D'Ottavio, J. Drozd, G.J. Marr, C. Mi
BNL, Upton, Long Island, New York, USA

Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy.
Power Supply checkout is a necessary, pre-beam, time-critical function. At odds are the desire to decrease the amount of time to perform the checkout while at the same time maximizing the number and types of checks that can be performed and analyzing the results quickly (in case any problems exist that must be addressed). Controls and Power Supply Group personnel have worked together to develop tools to accomplish these goals. Power Supply checkouts are now accomplished in a time-frame of hours rather than days, reducing the number of person-hours needed to accomplish the checkout and making the system available more quickly for beam development.

TUP225

Overview of Recent Studies and Modifications Being Made to RHIC to Mitigate the Effects of a Potential Failure to the Helium Distribution System

1241

J.E. Tuozzolo, D. Bruno, A. Di Lieto, G. Heppner, R. Karol, E.T. Lessard, C.J. Liaw, G.T. McIntyre, C. Mi, J. Reich, J. Sandberg, S.K. Seberg, L. Smart, T.N. Tallerico, R. Than, C. Theisen, R.J. Todd, R. Zapasek
BNL, Upton, Long Island, New York, USA

Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy.
In order to cool the superconducting magnets in RHIC, its helium refrigerator distributes 4.5 K helium throughout the tunnel via a series of distribution and return lines. The worst case for failure would be a release from the magnet distribution line, which operates at 3.5 to 4.5 atmospheres and contains the energized magnet bus. Should the bus insulation system fail or an electrical connection open, there is the potential for releasing up to 70 MJoules of stored energy. Studies were done to determine release rate of the helium and the resultant reduction in O2 concentration in the RHIC tunnel and service buildings. Equipment and components were also reviewed for reliability and the effects of 10 years of operations. Modifications were made to reduce the likelihood of failure and to reduce the amount of helium gas that could be released into tunnels and service buildings while personnel are present. This paper describes the issues reviewed, the steps taken, and remaining work to be done to reduce the hazards.

THP060

RHIC 12x150A Current Lead Temperature Controller: Design and Implementation

2238

C. Mi, D. Bruno, N.M. Day, A. Di Lieto, G. Ganetis, K. Hamdi, G. Heppner, J.P. Jamilkowski, W. Louie, J. Sandberg, S.K. Seberg, C. Sirio, J.E. Tuozzolo, K.L. Unger
BNL, Upton, Long Island, New York, USA

Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy
There are 60 12×150A current leads distributed in 6 RHIC service buildings; each current lead delivers power supply current from room temperature to cryogenic temperature in RHIC. Due to the humid environment, condensation frequently occurs and ice was quickly formed during operation, especially during an extensive storage period. This condition generated warnings and alarms that personal had to respond to, in order to provide temporary solutions, to keep the machine operational. A temperature control system was designed to avoid such occasions. We will discuss design, implementation and some results of this design in this paper.