| Paper | Title | Page |
|---|---|---|
| MOPRO033 | Design and Feasibility Study of a Transverse Halo Collimation System for ATF2 | 145 |
|
||
|
Funding: Work supported by FPA2010-21456-C02-01 and by i-link 0704 This paper presents the design of a halo collimation system for the ATF2 beamline. The main objective is the reduction of background noise that limits the performance of key diagnostic devices around the final focal point (IP), especially the Shintake Monitor (IPBSM) used for measuring the nanometer level vertical beam sizes and the future Diamond Sensor (DS) for measuring the beam halo. Beam tracking simulations have been performed to optimize the position and characteristics of the halo collimation devices. Furthermore the collimator wakefield-induced effect is being studied. |
||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-MOPRO033 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| THPME091 | Beam Halo Measurements using Wire Scanners at ATF2 | 3445 |
|
||
|
Funding: Chinese Scholarship Council, FPA2010-21456-C02-01 and i-link 0704 Beam halo hitting on the beam pipe after the Interaction Point (IP) can generate a large amount of background for the measurements of the nano meter beam size using the laser interferometer beam size monitor (Shintake monitor) at ATF2. In order to investigate the beam halo transverse distribution, a diamond detector will be installed downstream of the IP. A feasibility study of a transverse halo collimation system to reduce the background for these measurements is also in progress. Prior to the diamond detector installation, a first attempt of beam halo measurements have been performed in 2013 using the currently installed wire scanners. Modeling of the beam halo distribution in the extraction (EXT) line was done and compared with the old modeling for ATF. Beam halo measurements were also done using the post-IP wire scanner to investigate the beam halo distribution at post-IP. Work supported by Chinese Scholarship Council, FPA2010-21456-C02-01 and i-link 0704 |
||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME091 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| THPME092 | Status of Diamond Detector Development for Beam Halo Investigation at ATF2 | 3449 |
| SUSPSNE070 | use link to see paper's listing under its alternate paper code | |
|
||
|
Funding: Chinese Scholarship Council We are developing a diamond detector for beam halo and Compton spectrum diagnostics after the interaction point (IP) of ATF2, a low energy (1.3 GeV) prototype of the final focus system for ILC and CLIC linear collider projects. Tests of a 500 μm thick sCVD diamond detector with a dimension of 4.5 mm×4.5 mm have been carried out with radioactive sources and with electron beam from PHIL low energy (<10 MeV) photo-injector at LAL. The tests at PHIL were done with different beam intensities in air, just after the exit window at the end of the beam line, to test the response of the diamond detector and the readout electronics. We have successfully detected signals from single electrons, using a 40 dB amplifier, and from an electron beam of 108 electrons, using a 24 dB attenuator. A diamond sensor with 4 strips has been designed and fabricated for installation in the vacuum chambers of ATF2 and PHIL, with the aim to scan both the beam halo (with 2 strips of 1.5 mm×4 mm) and the beam core (with 2 strips of 0.1 mm×4 mm) transverse distributions. |
||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME092 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |
| THPME147 | The High Position Resolution Cavity BPM Developments and Measurement for ILC Final Focus System | 3599 |
|
||
| An ultra high position resolution cavity BPM was developed for the final focus system of ATF2, which is a accelerator test facility for ILC final focus system. The main purpose of ATF2 are achievement of 37 nm beam size and nano-meter beam orbit stability at IP(Interaction Point). For these purposes, a few nano meter beam position resolution was required for this cavity BPM, which is called the IP-BPM. The IP-BPM was fabricated 2 blocks of IP-BPM, the first block consists of two cavities in one block and second block consists of single cavity. IP-BPM can measure beam position in vertical and horizontal independently by using rectangular shape single cavity. Three IP-BPMs were installed at ATF IP region inside IP-chamber, and its position resolution was measured. We will present the detailed results on the beam tests. | ||
| DOI • | reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME147 | |
| Export • | reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml) | |