IPAC2014 - List of Authors (Pei, Y.J.)

Paper	Title	Page
THPME144	Stripline Beam Position Monitor for THz Source Based FEL	3590
	J. Xu, L. Li, J. Liu, P. Lu, Y.J. Pei, B.G. Sun, K. Tang, J.G. Wang, F.F. Wu, H. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou USTC/NSRL, Hefei, Anhui, People's Republic of China
	A 14MeV Linac with both the micro-pulse repetition rate 2856MHz and the macro-pulse width 6us for the THz Source Based FEL was proposed. In order to measure the beam position, a stripline beam position monitor (BPM) was designed, and a commercial BPM electronics Libera Brilliance Single Pass was adopted. As the input carrier frequency of the BPM electrode signal is 2856MHz, but the operating frequency of the Libera Brilliance Single Pass is 500MHz, so a front-end electronics was needed before the electrode signals feed into Libera Brilliance Single Pass. The front-end electronics was designed to make the BPM electrode signals of 2856MHz convert to 500MHz.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME144
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPRI048	Design of an Accelerating Tube for a Standing-wave Accelerator based on Genetic Algorithm’s Optimal Calculation	3875
SUSPSNE090	use link to see paper's listing under its alternate paper code
	Z.X. Tang USTC, Hefei, Anhui, People's Republic of China Y.J. Pei USTC/NSRL, Hefei, Anhui, People's Republic of China
	A compact medical standing-wave (SW) electron accelerating tube has been designed that operating frequency is 2998MHz, operating mode is π/2, final energy is 6MeV and beam current is 100mA based on genetic algorithm (GA)’s optimal calculation. It employed a bi-periodic structure with nose cone shape. We performed the simulation experiment which proved that GA was feasible and gave a set of geometric parameter with higher shunt impedance. We performed tuning of the whole tube by CST MICROWAVE STUDIO and SUPERFISH and calculation of beam dynamics by ASTRA and Parmela in this paper. The total length of the tube is less than 300mm.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPRI048
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Stripline Beam Position Monitor for THz Source Based FEL

3590

J. Xu, L. Li, J. Liu, P. Lu, Y.J. Pei, B.G. Sun, K. Tang, J.G. Wang, F.F. Wu, H. Xu, Y.L. Yang, Z.R. Zhou, J.Y. Zou
USTC/NSRL, Hefei, Anhui, People's Republic of China

A 14MeV Linac with both the micro-pulse repetition rate 2856MHz and the macro-pulse width 6us for the THz Source Based FEL was proposed. In order to measure the beam position, a stripline beam position monitor (BPM) was designed, and a commercial BPM electronics Libera Brilliance Single Pass was adopted. As the input carrier frequency of the BPM electrode signal is 2856MHz, but the operating frequency of the Libera Brilliance Single Pass is 500MHz, so a front-end electronics was needed before the electrode signals feed into Libera Brilliance Single Pass. The front-end electronics was designed to make the BPM electrode signals of 2856MHz convert to 500MHz.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPME144

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPRI048

Design of an Accelerating Tube for a Standing-wave Accelerator based on Genetic Algorithm’s Optimal Calculation

3875

SUSPSNE090

use link to see paper's listing under its alternate paper code

Z.X. Tang
USTC, Hefei, Anhui, People's Republic of China
Y.J. Pei
USTC/NSRL, Hefei, Anhui, People's Republic of China

A compact medical standing-wave (SW) electron accelerating tube has been designed that operating frequency is 2998MHz, operating mode is π/2, final energy is 6MeV and beam current is 100mA based on genetic algorithm (GA)’s optimal calculation. It employed a bi-periodic structure with nose cone shape. We performed the simulation experiment which proved that GA was feasible and gave a set of geometric parameter with higher shunt impedance. We performed tuning of the whole tube by CST MICROWAVE STUDIO and SUPERFISH and calculation of beam dynamics by ASTRA and Parmela in this paper. The total length of the tube is less than 300mm.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2014-THPRI048

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)