Author: Lee, W.W.
Paper Title Page
WEPWA043 Construction of Injector Test Facility (ITF) for the PAL XFEL 2220
  • S.J. Park, H. J. Choi, T. Ha, J.H. Han, J.H. Hong, W.H. Hwang, H.-S. Kang, T.-H. Kang, D.T. Kim, J.M. Kim, S.-C. Kim, I.S. Ko, B.H. Lee, H.-S. Lee, W.W. Lee, C.-K. Min, Y.J. Park, Y.G. Son
    PAL, Pohang, Kyungbuk, Republic of Korea
  • M.S. Chae
    POSTECH, Pohang, Kyungbuk, Republic of Korea
  Funding: Work supported by the Ministry of Education, Science and Technology (MEST) in Korea.
An injector test facility (ITF) for the PAL-XFEL has been successfully constructed and its commissioning is under way. The facility is to demonstrate beam performances required by the PAL XFEL (beam energy of 139 MeV, projected rms emittance of < 0.5 mm mrad @ 200 pC, and beam repetition rate of 60 Hz) with good enough stabilities. We have constructed a dedicated building for the facility in which a radiation-shielding tunnel (19.2-m long, 3.5-m wide, and 2.4-m high inner space), a klystron-modulator gallery, a laser room, and a control room are installed. The injector consists of an in-house-developed photo-cathode rf gun, a 30-mJ Ti:Sa laser system, two accelerating structures (as well as two sets of klystron-modulator systems), and various diagnostics as well as magnets & instrumentations. The installation of a transverse deflecting cavity (S-band, 10-fs resolution) and a laser heater is scheduled in 2013. In this article we report on the facility construction and some of the early commisisoning results.
WEPFI043 S-band High Stability Solid State Amplifier for 10 GeV PAL-XFEL 2800
  • W.H. Hwang, J.Y. Huang, H.-S. Kang, H.-S. Lee, W.W. Lee
    PAL, Pohang, Kyungbuk, Republic of Korea
  In PAL, We are constructing a 10GeV PxFEL project. The output power of the klystron is 80 MW at the pulse width of 4 ㎲ and the repetition rate of 60 Hz. And the specifications of the rf phase and amplitude stability are 0.05 degrees(rms) and 0.05%(rms) respectively. The SSA(Solid State Amplifier) is used for driver of 80MW Klystron. The output power of SSA is 800W. Also, the measured rf stability of SSA output is 0.03 degrees rms and 0.025 % rms. This paper describes the microwave system and the SSA for the PxFEL.  
THPME026 First Results of the PAL-XFEL Prototype Undulator Measurements 3561
  • D.E. Kim, H.S. Han, Y.-G. Jung, H.-G. Lee, S.B. Lee, W.W. Lee, K.-H. Park, H.S. Suh
    PAL, Pohang, Kyungbuk, Republic of Korea
  • M.-H. Cho, I.S. Ko
    POSTECH, Pohang, Kyungbuk, Republic of Korea
  Pohang Accelerator Laboratory (PAL) is developing 10 GeV, 0.1 nm SASE based FEL for high power, short pulse X-ray coherent photon sources named PAL-XFEL. At the first stage PAL-XFEL needs two undulator lines for photon source. PAL is developing undulator magnetic structure based on EU-XFEL design. The hard X-ray undulator features 7.2 mm min magnetic gap, and 5.0 m magnetic length with maximum effective magnetic field larger than 0.908 T to achieve 0.1nm radiation at 10 GeV electron energy. A prototype for PAL-XFEL Xray undulator line is completed and the measurement, correction results are summarized.  
THPME027 Design and Fabrication of Prototype Phase Shifter for PAL XFEL 3564
  • H.-G. Lee, Y.-G. Jung, H.-S. Kang, D.E. Kim, S.B. Lee, W.W. Lee, K.-H. Park, H.S. Suh
    PAL, Pohang, Kyungbuk, Republic of Korea
  Pohang Accelerator Laboratory(PAL) is developing a SASE X-ray Free Electron Laser based on 10 GeV linear accelerator. Prototype phase shifters are being developed to be used for the X-ray and Soft X-ray undulator line. The phase shifters will be used to adjust the phase of the electron beam with respect to that of the radiation field. Two prototype phase shifters are being developed. One is based on the EU-XFEL phase shifter using zero-potential iron yoke, and the other one is similar to FERMI phase shifter where only permanent magnets are used. Driving system consists of 5 phase stepping motor, left/right handed ball screw and absolute linear encoder. In this paper, we describe the design, fabrication and test results of the two phase shifter prototypes.