Author: Kakihara, K.
Paper Title Page
MOPFI018 Design Study of a New Large Aperture Flux Concentrator 318
  • L. Zang, M. Akemoto, S. Fukuda, K. Furukawa, T. Higo, K. Kakihara, T. Kamitani, Y. Ogawa, H. Someya, T. Takatomi
    KEK, Ibaraki, Japan
  For high luminosity electron-positron colliders, intense positron beam production is one of the key issues. Flux Concentrator (FC) is a pulsed solenoid that can generate high magnetic field of several Tesla and is often used for focusing positrons emerged from a production target. It works as an optical matching device in a positron capture section. With this device, high capture efficiency is achieved. In this paper, we will introduce a new design of a FC for the SuperKEKB positron source. The advantages of the new design are: 1. the aperture could be doubled of the previous design, 2. the transverse components are only 1/10 of the previous design, 3. maintain the same high peak longitudinal field. The new FC modeling has been done in CST Studio and we will report the results of new FC field evaluation. In order to calculate the positron yield and capture efficiency, a tracking simulation to the end of capture section has also been carried out, which is also included in this paper.  
TUPME010 High-intensity and Low-emittance Upgrade of 7-GeV Injector Linac towards SuperKEKB 1583
  • K. Furukawa, M. Akemoto, D.A. Arakawa, Y. Arakida, A. Enomoto, S. Fukuda, H. Honma, R. Ichimiya, N. Iida, M. Ikeda, E. Kadokura, K. Kakihara, T. Kamitani, H. Katagiri, M. Kurashina, S. Matsumoto, T. Matsumoto, H. Matsushita, S. Michizono, K. Mikawa, T. Miura, F. Miyahara, T. Mori, H. Nakajima, K. Nakao, T. Natsui, Y. Ogawa, S. Ohsawa, F. Qiu, M. Satoh, T. Shidara, A. Shirakawa, H. Sugimoto, T. Suwada, T. Takatomi, T. Takenaka, M. Tanaka, Y. Yano, K. Yokoyama, M. Yoshida, L. Zang, X. Zhou
    KEK, Ibaraki, Japan
  • D. Satoh
    TIT, Tokyo, Japan
  After a decade of successful operation at KEKB a new electron/positron collider, SuperKEKB, is being constructed to commission within FY2014. It aims at a luminosity of 8 x 1035 /s.cm2, 40-times higher than that of KEKB, in order to study the flavor physics of elementary particles further, by mainly squeezing the beams at the collision point. The injector linac should provide high-intensity and low-emittance beams of 7-GeV electron and 4-GeV positron by newly installing a RF-gun, a flux concentrator, and a damping ring with careful emittance and energy management. It also have to perform simultaneous top-up injections into four storage rings by pulse-to-pulse beam modulations not to interfare between three facilities of SuperKEKB, Photon Factory and PF-AR. This paper describes the injector design decisions and present status of the construction.  
WEPFI019 High Power Test of Kanthal-coated L-band Lossy Cavity 2744
  • F. Miyahara, Y. Arakida, Y. Higashi, T. Higo, K. Kakihara, S. Matsumoto
    KEK, Ibaraki, Japan
  • K. Saito
    Hitachi, Ltd., Energy and Environmental System Laboratory, Hitachi-shi, Japan
  • H. Sakurabata
    Hitachi, Ltd., Power & Industrial Systems R&D Laboratory, Ibaraki-ken, Japan
  We have been developing a Kanthal (Al-Cr-Fe)-coated collinear load as a possible candidate of the L-band acc. structure of SuperKEKB positron capture system. In order to achieve the higher capture efficiency comparing to that of KEKB, the upgrade of the e+ production and capture section is required. The system consists of a W target with a flux concentrator followed by acc. structures surrounded by solenoids. The increase of the e+ bunch charge and the reduction of satellite bunches are the main issues for this system. The frequency choice of L-band is based on the larger transverse and longitudinal acceptances than those of the S-band one. The load is preferable to compose the system with compact magnets and to minimize the dip in the solenoid field. The design of the load was reported in previous work*. We understand that the Kanthal-coated cell should be confirmed in high power to confirm the feasibility at our design field of 10 MV/m level. We are making a test cavity which consists of 3 cells and one of them is composed of Kanthal-coated disks to lower the intrinsic Q value from 20000 to the order of 1000. The cavity production and the experimental result will be reported.
*Development of L-band accelerating structure with Kanthal-coated collinear load for SuperKEKB, IPAC12, THLR04.