IPAC2013 - List of Authors (De Santis, S.)

Paper	Title	Page
MOPWA071	A Comparison of Electron Cloud Density Measurements at CesrTA	843
	J.P. Sikora, J.A. Crittenden, D.O. Duggins, Y. Li, X. Liu CLASSE, Ithaca, New York, USA S. De Santis LBNL, Berkeley, California, USA
	Funding: This work is supported by the US National Science Foundation PHY-0734867, PHY-1002467, and the US Department of Energy DE-FC02-08ER41538, DE-SC0006505. Several techniques have been employed to measure the electron cloud (EC) density in accelerators. These include Time Resolved Retarding Field Analyzers (TR-RFA) and Shielded Pickups (SPU) that measure the flux of cloud electrons onto the beam-pipe wall, as well as TE wave resonance techniques that measure the EC density in a region within the volume of the beam-pipe. We have made measurements to test the EC mitigation properties of different surface coatings and geometries, often with more than one technique used in the same test chamber. We present a comparison of bare aluminum chambers with those having a TiN coating, as well as the effect of beam conditioning. In addition, we will compare the results of the different measurement techniques used in the same chamber. These measurements were made at the Cornell Electron Storage Ring (CESR) which has been reconfigured as a test accelerator (CesrTA) having positron or electron beam energies ranging from 2 GeV to 5 GeV.

WEPWA070	Design of a Collimation System for the Next Generation Light Source	2277
	C. Steier, J.M. Byrd, S. De Santis, P. Emma, D. Li, H. Nishimura, C. F. Papadopoulos, H.J. Qian, F. Sannibale LBNL, Berkeley, California, USA
	Funding: This work is supported by the Director, Office of Science, Office of Basic Energy Sciences, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. The Next Generation Light Source at LBNL will deliver MHz repetition rate electron beams to an array of free electron lasers. Because of the high beam power approaching one MW in such a facility, effective beam collimation is extremely important to minimize radiation damage, prevent quenches of superconducting cavities, limit dose rates outside of the accelerator tunnel and prevent equipment damage. This paper describes the conceptual design of a collimation system, including detailed simulations to verify its effectiveness.

WEPME061	A Wideband Slotted Kicker Design for SPS Transverse Intra-bunch Feedback	3073
	J.M. Cesaratto, J.D. Fox, C.H. Rivetta SLAC, Menlo Park, California, USA D. Alesini, A. Drago, A. Gallo, F. Marcellini, M. Zobov INFN/LNF, Frascati (Roma), Italy S. De Santis LBNL, Berkeley, California, USA W. Höfle CERN, Geneva, Switzerland
	Funding: Work supported by the U.S. Department of Energy under contract DE-AC02-76SF00515 and the US LHC Accelerator Research Program (LARP) and by the EU FP7 HiLumi LHC - Grant Agreement 284404. Control and mitigation of transverse beam instabilities caused by electron cloud and TMCI will be essential for the SPS to meet the beam intensity demands for the HL-LHC upgrade. A wideband intra-bunch feedback method is in development, based on a 4 GS/s data acquisition and processing, and with a back end frequency structure extending to 1 GHz. A slotted type kicker, similar to those used for stochastic cooling, has been considered as the terminal element of the feedback chain. It offers the most promising deflecting structure characteristics to meet the system requirements in terms of bandwidth, shunt impedance, and beam coupling impedance. Different types of slotted structures have been explored and simulated, including a ridged waveguide and coaxial type waveguide. In this paper we present our findings and the conceptual design of a vertical SPS wideband kicker consistent with the stay clear, vacuum, frequency band coverage, and peak shunt impedance requirements.

Paper

Title

Page

A Comparison of Electron Cloud Density Measurements at CesrTA

843

J.P. Sikora, J.A. Crittenden, D.O. Duggins, Y. Li, X. Liu
CLASSE, Ithaca, New York, USA
S. De Santis
LBNL, Berkeley, California, USA

Funding: This work is supported by the US National Science Foundation PHY-0734867, PHY-1002467, and the US Department of Energy DE-FC02-08ER41538, DE-SC0006505.
Several techniques have been employed to measure the electron cloud (EC) density in accelerators. These include Time Resolved Retarding Field Analyzers (TR-RFA) and Shielded Pickups (SPU) that measure the flux of cloud electrons onto the beam-pipe wall, as well as TE wave resonance techniques that measure the EC density in a region within the volume of the beam-pipe. We have made measurements to test the EC mitigation properties of different surface coatings and geometries, often with more than one technique used in the same test chamber. We present a comparison of bare aluminum chambers with those having a TiN coating, as well as the effect of beam conditioning. In addition, we will compare the results of the different measurement techniques used in the same chamber. These measurements were made at the Cornell Electron Storage Ring (CESR) which has been reconfigured as a test accelerator (CesrTA) having positron or electron beam energies ranging from 2 GeV to 5 GeV.

WEPWA070

Design of a Collimation System for the Next Generation Light Source

2277

C. Steier, J.M. Byrd, S. De Santis, P. Emma, D. Li, H. Nishimura, C. F. Papadopoulos, H.J. Qian, F. Sannibale
LBNL, Berkeley, California, USA

Funding: This work is supported by the Director, Office of Science, Office of Basic Energy Sciences, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
The Next Generation Light Source at LBNL will deliver MHz repetition rate electron beams to an array of free electron lasers. Because of the high beam power approaching one MW in such a facility, effective beam collimation is extremely important to minimize radiation damage, prevent quenches of superconducting cavities, limit dose rates outside of the accelerator tunnel and prevent equipment damage. This paper describes the conceptual design of a collimation system, including detailed simulations to verify its effectiveness.

WEPME061

A Wideband Slotted Kicker Design for SPS Transverse Intra-bunch Feedback

3073

J.M. Cesaratto, J.D. Fox, C.H. Rivetta
SLAC, Menlo Park, California, USA
D. Alesini, A. Drago, A. Gallo, F. Marcellini, M. Zobov
INFN/LNF, Frascati (Roma), Italy
S. De Santis
LBNL, Berkeley, California, USA
W. Höfle
CERN, Geneva, Switzerland

Funding: Work supported by the U.S. Department of Energy under contract DE-AC02-76SF00515 and the US LHC Accelerator Research Program (LARP) and by the EU FP7 HiLumi LHC - Grant Agreement 284404.
Control and mitigation of transverse beam instabilities caused by electron cloud and TMCI will be essential for the SPS to meet the beam intensity demands for the HL-LHC upgrade. A wideband intra-bunch feedback method is in development, based on a 4 GS/s data acquisition and processing, and with a back end frequency structure extending to 1 GHz. A slotted type kicker, similar to those used for stochastic cooling, has been considered as the terminal element of the feedback chain. It offers the most promising deflecting structure characteristics to meet the system requirements in terms of bandwidth, shunt impedance, and beam coupling impedance. Different types of slotted structures have been explored and simulated, including a ridged waveguide and coaxial type waveguide. In this paper we present our findings and the conceptual design of a vertical SPS wideband kicker consistent with the stay clear, vacuum, frequency band coverage, and peak shunt impedance requirements.