Author: Miller, S.J.
Paper Title Page
MOOAC03 Superconducting Resonators Development for the FRIB and ReA Linacs at MSU: Recent Achievements and Future Goals 61
 
  • A. Facco
    INFN/LNL, Legnaro (PD), Italy
  • E.C. Bernard, J. Binkowski, C. Compton, J.L. Crisp, L.J. Dubbs, K. Elliott, A. Facco, L.L. Harle, M. Hodek, M.J. Johnson, D. Leitner, M. Leitner, I.M. Malloch, S.J. Miller, R. Oweiss, J. Popielarski, L. Popielarski, K. Saito, J. Wei, J. Wlodarczak, Y. Xu, Y. Zhang, Z. Zheng
    FRIB, East Lansing, Michigan, USA
  • A. Burrill, G.K. Davis, K. Macha, A.V. Reilly
    JLAB, Newport News, Virginia, USA
 
  Funding: This material is based upon work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661
The superconducting driver and post-accelerator linacs of the FRIB project, the large scale radioactive beam facility under construction at MSU, require the construction of about 400 low-beta Quarter-wave (QWR) and Half-wave resonators (HWR) with four different optimum velocities. 1st and 2nd generation prototypes of β=0.041 and 0.085 QWRs and β=0.53 HWRs have been built and tested, and have more than fulfilled the FRIB and ReA design goals. The present cavity surface preparation at MSU allowed production of low-beta cavities nearly free from field emission. The first two cryostats of β=0.041 QWRs are now in operation in the ReA3 linac. A 3rd generation design of the FRIB resonators allowed to further improve the cavity parameters, reducing the peak magnetic field in operation and increasing the possible operation gradient , with consequent reduction of the number of required resonators. The construction of the cavities for FRIB, which includes three phases for each cavity type (development, pre-production and production runs) has started. Cavity design, construction, treatment and performance will be described and discussed.
Michigan State University designs and establishes FRIB as a DOE Office of Science National User Facility in support of the mission of the Office of Nuclear Physics.
 
slides icon Slides MOOAC03 [4.009 MB]  
 
WEPPD006 Design of the FRIB Cryomodule 2507
 
  • M.J. Johnson, M. Barrios, J. Binkowski, S. Bricker, F. Casagrande, A.D. Fox, B.R. Lang, M. Leitner, S.J. Miller, T. Nellis, J.P. Ozelis, X. Rao, J. Weisend, Y. Xu
    FRIB, East Lansing, Michigan, USA
  • D. Arenius, V. Ganni, W.J. Schneider, M. Wiseman
    JLAB, Newport News, Virginia, USA
 
  Funding: This material is based upon work supported by the U.S. Department of Energy Office of Science under Cooperative Agreement DE-SC0000661
An advanced, modular bottom-supported cryomodule design is described which is highly optimized for mass-production and efficient precision-assembly. The FRIB driver linac uses 4 types of superconducting resonators and 2 solenoid lengths which in turn require 7 individual cryomodule configurations. To meet alignment tolerances a precision-machined bolted cryomodule rail system is described. A novel, kinematic mounting system of the cold mass is introduced which allows for thermal contractions while preserving alignment. A first prototype will incorporate a wire position monitor for alignment verification. The cold alignment structure is supported by composite posts which also function as thermal isolators. The cryogenic system provides separate 2 K and 4.5 K liquid helium lines to cavities and solenoids. Details of the JT valves, heat exchanger, cool-down circuit and junction to cryogenic line will be provided. Transient cool-down was simulated for stresses and buckling failure. A 1100-O Aluminum shield is used as a thermal radiation shield. The paper also describes cryomodule interfaces with the linac tunnel, the RF input cables, and the cryogenic distribution system.
Michigan State University designs and establishes FRIB as a DOE Office of Science National User Facility in support of the mission of the Office of Nuclear Physics.