Author: Liu, J.
Paper Title Page
WEPPC040 Evaluation of VATSEAL Technology to Seal Waveguide Serving High-field Superconducting RF Cavities 2298
 
  • B.K. Stillwell, J.D. Fuerst, J. Liu, G.J. Waldschmidt, G. Wu
    ANL, Argonne, USA
 
  Funding: Work supported by U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
A waveguide flange seal serving a high-field, superconducting, radio-frequency (SRF) cavity ideally possesses several characteristics. Seals must generally be ultrahigh-vacuum leak tight. Seals must also bridge the inner surfaces of connecting flanges for optimum transmission and minimal heating due to trapped modes. In addition, if seal contact areas are minimized, flange seals may serve as convenient thermal impedances. Finally, seals must be easily cleanable and not be prone to generate particulate matter during assembly and disassembly. A unique sealing technology known as VATSEAL may neatly address all of the above requirements. In this paper, we describe our evaluation of VATSEAL technology for use in SRF cavity assemblies.
 
 
WEPPC038 Status of the Short-Pulse X-ray Project at the Advanced Photon Source 2292
 
  • A. Nassiri, N.D. Arnold, T.G. Berenc, M. Borland, B. Brajuskovic, D.J. Bromberek, J. Carwardine, G. Decker, L. Emery, J.D. Fuerst, A.E. Grelick, D. Horan, J. Kaluzny, F. Lenkszus, R.M. Lill, J. Liu, H. Ma, V. Sajaev, T.L. Smith, B.K. Stillwell, G.J. Waldschmidt, G. Wu, B.X. Yang, Y. Yang, A. Zholents
    ANL, Argonne, USA
  • J.M. Byrd, L.R. Doolittle, G. Huang
    LBNL, Berkeley, California, USA
  • G. Cheng, G. Ciovati, P. Dhakal, G.V. Eremeev, J.J. Feingold, R.L. Geng, J. Henry, P. Kneisel, K. Macha, J.D. Mammosser, J. Matalevich, A.D. Palczewski, R.A. Rimmer, H. Wang, K.M. Wilson, M. Wiseman
    JLAB, Newport News, Virginia, USA
  • Z. Li, L. Xiao
    SLAC, Menlo Park, California, USA
 
  Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
The Advanced Photon Source Upgrade (APS-U) Project at Argonne will include generation of short-pulse x-rays based on Zholents’* deflecting cavity scheme. We have chosen superconducting (SC) cavities in order to have a continuous train of crabbed bunches and flexibility of operating modes. In collaboration with Jefferson Laboratory, we are prototyping and testing a number of single-cell deflecting cavities and associated auxiliary systems with promising initial results. In collaboration with Lawrence Berkeley National Laboratory, we are working to develop state-of-the-art timing, synchronization, and differential rf phase stability systems that are required for SPX. Collaboration with Advanced Computations Department at Stanford Linear Accelerator Center is looking into simulations of complex, multi-cavity geometries with lower- and higher-order modes waveguide dampers using ACE3P. This contribution provides the current R&D status of the SPX project.
* A. Zholents et al., NIM A 425, 385 (1999).
 
 
THPPC029 High-power Waveguide Dampers for the Short-Pulse X-Ray Project at the Advanced Photon Source 3344
 
  • G.J. Waldschmidt, B. Brajuskovic, J. Liu, M.E. Middendorf, A. Nassiri, T.L. Smith, G. Wu
    ANL, Argonne, USA
  • J. Henry, J.D. Mammosser, R.A. Rimmer, M. Wiseman
    JLAB, Newport News, Virginia, USA
 
  Funding: Work supported by U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
High-power waveguide dampers have been designed and prototyped for the Short-Pulse X-ray (SPX) cavities at the Advanced Photon Source. The cavities will operate at 2.815 GHz and utilize the TM110 dipole mode. As a result, higher-order (HOM) and lower-order mode (LOM) in-vacuum dampers have been designed to satisfy the demanding broadband damping requirements in the APS storage ring. The SPX single-cell cavity consists of two WR284 waveguides for damping the HOMs and one WR284 waveguide for primarily damping the LOM where up to 2kW will be dissipated in the damping material. The damper designs and high-power experimental results will be discussed in this paper.