IPAC2012 - List of Authors (Lee, D.)

Paper	Title	Page
WEPPD046	Design of Machine Protection System for the Taiwan Photon Source	2618
	C.Y. Liao, J. Chen, Y.-S. Cheng, K.T. Hsu, K.H. Hu, C.H. Kuo, D. Lee, C.Y. Wu NSRRC, Hsinchu, Taiwan
	The Taiwan Photon Source (TPS) is being constructed at the campus of the NSRRC (National Synchrotron Radiation Research Center). In order to prevent damage to accelerator components induced by various events, design of the global machine protection system (MPS) is on-going. The MPS collect interlock and beam dump request from various system, perform decision, transmit dump beam request to RF system. The PLC based system will be used as a slow MPS which can delivery less than 8 msec reaction time. The fast MPS will dependent on event based timing system to deliver response time less than 5 μsec. Trigger signal for post-mortem will also be distributed by the fast MPS. To ensure alive of the system, several self-diagnostics mechanisms include heartbeat and transient capture will be implemented. The MPS architecture, plans and implementation were presented in this report.

THPPR011	Insertion Device Controls Plan of the Taiwan Photon Source	3987
	C.Y. Wu, J. Chen, Y.-S. Cheng, K.T. Hsu, S.Y. Hsu, K.H. Hu, C.H. Kuo, D. Lee, C.Y. Liao NSRRC, Hsinchu, Taiwan
	Insertion device (ID) is a crucial component in third-generation synchrotron light sources, which can produces highly-brilliant, forward-directed and quasi-monochromatic radiation over a broad energy range for various experiments. In the phase I of the Taiwan Photon Source (TPS) project, ten insertion devices (IDs) will be planned, constructed, and installed for the first seven beamlines. The control system for all the IDs is based on the EPICS architecture. The main control components include the motor with encoder for gap adjustment, trim coil power supply for corrector magnets, temperature sensor for ID environmental monitoring and baking (only for In-Vacuum Undulator), and interlock system (limit switches, tilt sensor) for safety. The progress of the controls plan will be summarized in this report.

Paper

Title

Page

Design of Machine Protection System for the Taiwan Photon Source

2618

C.Y. Liao, J. Chen, Y.-S. Cheng, K.T. Hsu, K.H. Hu, C.H. Kuo, D. Lee, C.Y. Wu
NSRRC, Hsinchu, Taiwan

The Taiwan Photon Source (TPS) is being constructed at the campus of the NSRRC (National Synchrotron Radiation Research Center). In order to prevent damage to accelerator components induced by various events, design of the global machine protection system (MPS) is on-going. The MPS collect interlock and beam dump request from various system, perform decision, transmit dump beam request to RF system. The PLC based system will be used as a slow MPS which can delivery less than 8 msec reaction time. The fast MPS will dependent on event based timing system to deliver response time less than 5 μsec. Trigger signal for post-mortem will also be distributed by the fast MPS. To ensure alive of the system, several self-diagnostics mechanisms include heartbeat and transient capture will be implemented. The MPS architecture, plans and implementation were presented in this report.

THPPR011

Insertion Device Controls Plan of the Taiwan Photon Source

3987

C.Y. Wu, J. Chen, Y.-S. Cheng, K.T. Hsu, S.Y. Hsu, K.H. Hu, C.H. Kuo, D. Lee, C.Y. Liao
NSRRC, Hsinchu, Taiwan

Insertion device (ID) is a crucial component in third-generation synchrotron light sources, which can produces highly-brilliant, forward-directed and quasi-monochromatic radiation over a broad energy range for various experiments. In the phase I of the Taiwan Photon Source (TPS) project, ten insertion devices (IDs) will be planned, constructed, and installed for the first seven beamlines. The control system for all the IDs is based on the EPICS architecture. The main control components include the motor with encoder for gap adjustment, trim coil power supply for corrector magnets, temperature sensor for ID environmental monitoring and baking (only for In-Vacuum Undulator), and interlock system (limit switches, tilt sensor) for safety. The progress of the controls plan will be summarized in this report.