IPAC2012 - List of Authors (Emma, P.)

Paper

Title

Page

Resistive Wall Heating of the Undulator in High Repetition Rate FELs

652

J. Qiang, J.N. Corlett, P. Emma
LBNL, Berkeley, California, USA
J. Wu
SLAC, Menlo Park, California, USA

Funding: Work supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
In next generation high repetition rate FELs, beam energy loss due to resistive wall wakefields will produce significant amount of heat. The heat load for a superconducting undulator (operating at low temperature), must be removed and will be expensive to remove. In this paper, we study this effect in an undulator proposed for a Next Generation Light Source (NGLS) at LBNL. We benchmark our calculations with measurements at the LCLS and carry out detailed parameter studies using beam from a start-to-end simulation. Our preliminary results suggest that the heat load in the undulator is about 2 W/m with an aperture size of 6 mm for nominal NGLS design parameters.

TUPPP038

Electron Beam Collimation for the Next Generation Light Source

1695

C. Steier, P. Emma, H. Nishimura, C. F. Papadopoulos, F. Sannibale
LBNL, Berkeley, California, USA

Funding: Work supported by the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
The Next Generation Light Source will deliver high (MHz) repetition rate electron beams to an array of free electron lasers. Because of the significant average current in such a facility, effective beam collimation is extremely important to minimize radiation damage to undulators, prevent quenches of superconducting cavities, limit dose rates outside of the accelerator tunnel and prevent equipment damage. This paper describes the conceptual design of the collimator system, as well as the results of simulations to test its effectiveness.

TUPPP070

Next Generation Light Source R&D and Design Studies at LBNL

1762

J.N. Corlett, B. Austin, K.M. Baptiste, D.L. Bowring, J.M. Byrd, S. De Santis, P. Denes, R.J. Donahue, L.R. Doolittle, P. Emma, D. Filippetto, G. Huang, T. Koettig, S. Kwiatkowski, D. Li, T.P. Lou, H. Nishimura, H.A. Padmore, C. F. Papadopoulos, G.C. Pappas, G. Penn, M. Placidi, S. Prestemon, D. Prosnitz, J. Qiang, A. Ratti, M.W. Reinsch, D. Robin, F. Sannibale, D. Schlueter, R.W. Schoenlein, J.W. Staples, C. Steier, C. Sun, T. Vecchione, M. Venturini, W. Wan, R.P. Wells, R.B. Wilcox, J.S. Wurtele
LBNL, Berkeley, California, USA

Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
LBNL is developing design concepts for a multi-beamline soft x-ray FEL array powered by a superconducting linear accelerator, operating with a high bunch repetition rate of approximately one MHz. The cw superconducting linear accelerator is supplied by an injector based on a high-brightness, high-repetition-rate photocathode electron gun. Electron bunches are distributed from the linac to the array of independently configurable FEL beamlines with nominal bunch rates up to 100 kHz in each FEL, and with even pulse spacing. Individual FELs may be configured for different modes of operation, and each may produce high peak and average brightness x-rays with a flexible pulse format, and with pulse durations ranging from sub-femtoseconds to hundreds of femtoseconds. In this paper we describe conceptual design studies and optimizations. We describe recent developments in the design and performance parameters, and progress in R&D activities.

TUPPP071

Design Concepts of a Beam Spreader for a Next Generation Free Electron Laser

1765

M. Placidi, P. Emma, J.-Y. Jung, G.C. Pappas, D. Robin, C. Sun, W. Wan
LBNL, Berkeley, California, USA

LBNL is developing design concepts for a multi-beamline soft x-ray FEL array powered by a superconducting linear accelerator, operating with a high bunch repetition rate of approximately one MHz. Electron bunches are distributed from the linac to the array (up to 10) independently configurable FEL beamlines with nominal bunch rates up to 100 kHz in each FEL, and with even pulse spacing. This distribution to the different FELs is made by the beam spreader for which the design has to relative compact while not significantly perturbing the quality of the electron beam and subsequent performance of the FELs. We report on our conceptual design for the spreader. The spreader lattice has two distinct parts, namely the beam take-off section and the FEL fan-out distributions section. Each section is achromatic and isochronous. The effect of coherent synchrotron radiation and micro-bunching has been studied when passing through the spreader and simulations show no significant deterioration in the beam quality.

TUPPP073

Machine Parameter Studies for an FEL Facility Using STAFF

1768

M.W. Reinsch, B. Austin, J.N. Corlett, L.R. Doolittle, P. Emma, G. Penn, D. Prosnitz, J. Qiang, A. Sessler, M. Venturini
LBNL, Berkeley, California, USA
J.S. Wurtele
UCB, Berkeley, California, USA

Designing an FEL facility requires balancing multiple science needs, FEL and accelerator physics constraints, and engineering limitations. STAFF (System Trade Analysis for an FEL Facility) is a MATLAB program that enables the user to rapidly explore a large range of Linac and FEL design options to meet science requirements. The code uses analytical models such as the Ming Xie formulas when appropriate and look-up tables when necessary to maintain speed and flexibility. STAFF's modular design simplifies the inclusion of new physics models for FEL harmonics, wake fields, cavity higher-order modes and aspects of linac design such as the optimization of a laser heater, harmonic linearizer, and one or more bunch compressors. Code for the microbunching instability has been included as well. STAFF also supports multiple undulator technologies. STAFF permits the user to study error tolerances and multiple beamlines so as to explore the full capabilities of an entire user facility. This makes it possible to optimize the integrated system in terms of performance metrics such as photons/pulse, photons/sec and tunability range.

TUPPP074

Beam Dynamics Studies of a High-repetition Rate Linac Driver for a 4th-generation Light Source

1771

M. Venturini, J.N. Corlett, P. Emma, C. F. Papadopoulos, G. Penn, M. Placidi, J. Qiang, M.W. Reinsch, F. Sannibale, C. Steier, R.P. Wells
LBNL, Berkeley, California, USA

We present progress toward the design of a super-conducting linac driver of a high repetition rate FEL-based soft x-ray light source. The machine is intended to accept beams generated by the APEX* photocathode gun, operating in the MHz range, and deliver them to an array of SASE and seeded FEL beamlines. After reviewing the beam-dynamics considerations that are informing specific lattice choices we discuss the expected performance of the proposed machine design and its ability to meet the desired FEL specifications. We consider the merit of possible alternate designs (e.g., a one-stage compressor vs. a two-stage compressor) and the trade-offs between competing demands on the beam attributes (e.g., high peak current vs. acceptable energy spread).
* F. Sannibale et al., this conference.

WEEPPB004

Status of the APEX Project at LBNL

2173

F. Sannibale, B.J. Bailey, K.M. Baptiste, J.M. Byrd, C.W. Cork, J.N. Corlett, S. De Santis, L.R. Doolittle, J.A. Doyle, P. Emma, J. Feng, D. Filippetto, G. Huang, H. Huang, T.D. Kramasz, S. Kwiatkowski, W.E. Norum, H.A. Padmore, C. F. Papadopoulos, G.C. Pappas, G.J. Portmann, J. Qiang, D.G. Quintas, J.W. Staples, T. Vecchione, M. Venturini, M. Vinco, W. Wan, R.P. Wells, M.S. Zolotorev, F.A. Zucca
LBNL, Berkeley, California, USA
M. J. Messerly, M.A. Prantil
LLNL, Livermore, California, USA
C.M. Pogue
NPS, Monterey, California, USA

Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231.
The Advanced Photo-injector Experiment (APEX) at the Lawrence Berkeley National Laboratory is focused on the development of a high-brightness high-repetition rate (MHz-class) electron injector for X-ray FEL applications. The injector is based on a new concept gun, utilizing a normal conducting 186 MHz RF cavity operating in cw mode in conjunction with high quantum efficiency photocathodes capable of delivering the required repetition rates with available laser technology. The APEX activities are staged in 3 main phases. In Phases 0 and I, the gun will be tested at its nominal energy of 750 keV and several different photocathodes are tested at full repetition rate. In Phase II, a pulsed linac will be added for accelerating the beam at several tens of MeV to reduce space charge effects and measure the high-brightness performance of the gun when integrated in an injector scheme. At Phase II energies, the radiation shielding configuration of APEX limits the repetition rate to a maximum of several Hz. Phase 0 is under commissioning, Phase I under installation, and initial activities for Phase II are underway. This paper presents an update on the status of these activities.

WEPPP073

Dynamic Feedback Model for High Repetition Rate Linac-driven FELs

2879

J.M. Byrd, L.R. Doolittle, P. Emma, G. Huang, A. Ratti, C. Serrano
LBNL, Berkeley, California, USA

Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
One of the concepts for the next generation of linac-driven FELs is a cw superconducting linac driving an electron beam with MHz repetition rates. One of the challenges for next generation FELs is improve the shot-to-shot stability of the energy, charge, peak current, and timing jitter of the electron beam. The use of a cw RF system with MHz beam repetition rates presents an opportunity to use broadband feedback to stabilize the beam parameters. To understand the performance of such a feedback system, we are are developing a dynamic feedback model of the machine with a focus on the longitudinal beam properties. The model is being developed as an extension of the LITrack code and will include the dynamics of the beam-cavity interaction, RF feedback, beam-based feedback, and multibunch effects. In this paper, we will present the status of this model along with results.

WEPPR031

Injector Beam Dynamics for a High-repetition Rate 4th-generation Light Source

3000

C. F. Papadopoulos, J.N. Corlett, P. Emma, D. Filippetto, G. Penn, J. Qiang, M.W. Reinsch, F. Sannibale, C. Steier, M. Venturini, R.P. Wells
LBNL, Berkeley, California, USA

Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231.
We report on the beam dynamics studies and optimization methods for a high-repetition (1 MHz) photoinjector based on a VHF normal conducting electron source. The simultaneous goals of beam compression and preservation of 6-dimensional beam brightness have to be achieved in the injector, in order to accommodate a linac driven FEL light source. For this, a parallel, multiobjective optimization algorithm is used. We discuss the relative merits of different injector design points, as well as the constraints imposed on the beam dynamics by technical considerations such as the high repetition rate.

WEYB02

Hard X-ray Self-seeding at the Linac Coherent Light Source

P. Emma, J.W. Amann, F.-J. Decker, Y.T. Ding, Y. Feng, J.C. Frisch, D. Fritz, J.B. Hastings, Z. Huang, J. Krzywinski, H. Loos, A.A. Lutman, H.-D. Nuhn, D.F. Ratner, J.A. Rzepiela, S. Spampinati, D.R. Walz, J.J. Welch, J. Wu, D. Zhu
SLAC, Menlo Park, California, USA
W. Berg, R.R. Lindberg, D. Shu, Yu. Shvyd'ko, S. Stoupin, E. Trakhtenberg, A. Zholents
ANL, Argonne, USA
V.D. Blank, S. Terentiev
TISNCM, Troitsk, Russia

Funding: Work supported by US Department of Energy, contract number DE-AC02-76SF00515.
We report on experimental results of FEL self-seeding with Angstrom wavelengths at the Linac Coherent Light Source (LCLS) at SLAC. The scheme, suggested at DESY*, replaces the 16th 4-m long undulator segment (out of 33 total) with a weak magnetic chicane and a diamond-based monochromator in Bragg transmission geometry. The monochromatized SASE FEL pulse from the first half of the undulator line then seeds the second half. This demonstration of hard x-ray self-seeding is shown to narrow the FEL bandwidth by a factor 40-50, allows longitudinally coherent x-ray pulses near the Fourier-transform limit, and may eventually allow an increases in peak brightness by 1-2 orders of magnitude after applying an aggressive undulator field taper.
* G. Geloni, V. Kocharyan, E. Saldin, DESY 10-133, Aug. 2010.

Slides WEYB02 [5.946 MB]

Paper	Title	Page
MOPPP040	Resistive Wall Heating of the Undulator in High Repetition Rate FELs	652
	J. Qiang, J.N. Corlett, P. Emma LBNL, Berkeley, California, USA J. Wu SLAC, Menlo Park, California, USA
	Funding: Work supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. In next generation high repetition rate FELs, beam energy loss due to resistive wall wakefields will produce significant amount of heat. The heat load for a superconducting undulator (operating at low temperature), must be removed and will be expensive to remove. In this paper, we study this effect in an undulator proposed for a Next Generation Light Source (NGLS) at LBNL. We benchmark our calculations with measurements at the LCLS and carry out detailed parameter studies using beam from a start-to-end simulation. Our preliminary results suggest that the heat load in the undulator is about 2 W/m with an aperture size of 6 mm for nominal NGLS design parameters.

TUPPP038	Electron Beam Collimation for the Next Generation Light Source	1695
	C. Steier, P. Emma, H. Nishimura, C. F. Papadopoulos, F. Sannibale LBNL, Berkeley, California, USA
	Funding: Work supported by the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. The Next Generation Light Source will deliver high (MHz) repetition rate electron beams to an array of free electron lasers. Because of the significant average current in such a facility, effective beam collimation is extremely important to minimize radiation damage to undulators, prevent quenches of superconducting cavities, limit dose rates outside of the accelerator tunnel and prevent equipment damage. This paper describes the conceptual design of the collimator system, as well as the results of simulations to test its effectiveness.

TUPPP070	Next Generation Light Source R&D and Design Studies at LBNL	1762
	J.N. Corlett, B. Austin, K.M. Baptiste, D.L. Bowring, J.M. Byrd, S. De Santis, P. Denes, R.J. Donahue, L.R. Doolittle, P. Emma, D. Filippetto, G. Huang, T. Koettig, S. Kwiatkowski, D. Li, T.P. Lou, H. Nishimura, H.A. Padmore, C. F. Papadopoulos, G.C. Pappas, G. Penn, M. Placidi, S. Prestemon, D. Prosnitz, J. Qiang, A. Ratti, M.W. Reinsch, D. Robin, F. Sannibale, D. Schlueter, R.W. Schoenlein, J.W. Staples, C. Steier, C. Sun, T. Vecchione, M. Venturini, W. Wan, R.P. Wells, R.B. Wilcox, J.S. Wurtele LBNL, Berkeley, California, USA
	Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. LBNL is developing design concepts for a multi-beamline soft x-ray FEL array powered by a superconducting linear accelerator, operating with a high bunch repetition rate of approximately one MHz. The cw superconducting linear accelerator is supplied by an injector based on a high-brightness, high-repetition-rate photocathode electron gun. Electron bunches are distributed from the linac to the array of independently configurable FEL beamlines with nominal bunch rates up to 100 kHz in each FEL, and with even pulse spacing. Individual FELs may be configured for different modes of operation, and each may produce high peak and average brightness x-rays with a flexible pulse format, and with pulse durations ranging from sub-femtoseconds to hundreds of femtoseconds. In this paper we describe conceptual design studies and optimizations. We describe recent developments in the design and performance parameters, and progress in R&D activities.

TUPPP071	Design Concepts of a Beam Spreader for a Next Generation Free Electron Laser	1765
	M. Placidi, P. Emma, J.-Y. Jung, G.C. Pappas, D. Robin, C. Sun, W. Wan LBNL, Berkeley, California, USA
	LBNL is developing design concepts for a multi-beamline soft x-ray FEL array powered by a superconducting linear accelerator, operating with a high bunch repetition rate of approximately one MHz. Electron bunches are distributed from the linac to the array (up to 10) independently configurable FEL beamlines with nominal bunch rates up to 100 kHz in each FEL, and with even pulse spacing. This distribution to the different FELs is made by the beam spreader for which the design has to relative compact while not significantly perturbing the quality of the electron beam and subsequent performance of the FELs. We report on our conceptual design for the spreader. The spreader lattice has two distinct parts, namely the beam take-off section and the FEL fan-out distributions section. Each section is achromatic and isochronous. The effect of coherent synchrotron radiation and micro-bunching has been studied when passing through the spreader and simulations show no significant deterioration in the beam quality.

TUPPP073	Machine Parameter Studies for an FEL Facility Using STAFF	1768
	M.W. Reinsch, B. Austin, J.N. Corlett, L.R. Doolittle, P. Emma, G. Penn, D. Prosnitz, J. Qiang, A. Sessler, M. Venturini LBNL, Berkeley, California, USA J.S. Wurtele UCB, Berkeley, California, USA
	Designing an FEL facility requires balancing multiple science needs, FEL and accelerator physics constraints, and engineering limitations. STAFF (System Trade Analysis for an FEL Facility) is a MATLAB program that enables the user to rapidly explore a large range of Linac and FEL design options to meet science requirements. The code uses analytical models such as the Ming Xie formulas when appropriate and look-up tables when necessary to maintain speed and flexibility. STAFF's modular design simplifies the inclusion of new physics models for FEL harmonics, wake fields, cavity higher-order modes and aspects of linac design such as the optimization of a laser heater, harmonic linearizer, and one or more bunch compressors. Code for the microbunching instability has been included as well. STAFF also supports multiple undulator technologies. STAFF permits the user to study error tolerances and multiple beamlines so as to explore the full capabilities of an entire user facility. This makes it possible to optimize the integrated system in terms of performance metrics such as photons/pulse, photons/sec and tunability range.

TUPPP074	Beam Dynamics Studies of a High-repetition Rate Linac Driver for a 4th-generation Light Source	1771
	M. Venturini, J.N. Corlett, P. Emma, C. F. Papadopoulos, G. Penn, M. Placidi, J. Qiang, M.W. Reinsch, F. Sannibale, C. Steier, R.P. Wells LBNL, Berkeley, California, USA
	We present progress toward the design of a super-conducting linac driver of a high repetition rate FEL-based soft x-ray light source. The machine is intended to accept beams generated by the APEX* photocathode gun, operating in the MHz range, and deliver them to an array of SASE and seeded FEL beamlines. After reviewing the beam-dynamics considerations that are informing specific lattice choices we discuss the expected performance of the proposed machine design and its ability to meet the desired FEL specifications. We consider the merit of possible alternate designs (e.g., a one-stage compressor vs. a two-stage compressor) and the trade-offs between competing demands on the beam attributes (e.g., high peak current vs. acceptable energy spread). * F. Sannibale et al., this conference.

WEEPPB004	Status of the APEX Project at LBNL	2173
	F. Sannibale, B.J. Bailey, K.M. Baptiste, J.M. Byrd, C.W. Cork, J.N. Corlett, S. De Santis, L.R. Doolittle, J.A. Doyle, P. Emma, J. Feng, D. Filippetto, G. Huang, H. Huang, T.D. Kramasz, S. Kwiatkowski, W.E. Norum, H.A. Padmore, C. F. Papadopoulos, G.C. Pappas, G.J. Portmann, J. Qiang, D.G. Quintas, J.W. Staples, T. Vecchione, M. Venturini, M. Vinco, W. Wan, R.P. Wells, M.S. Zolotorev, F.A. Zucca LBNL, Berkeley, California, USA M. J. Messerly, M.A. Prantil LLNL, Livermore, California, USA C.M. Pogue NPS, Monterey, California, USA
	Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231. The Advanced Photo-injector Experiment (APEX) at the Lawrence Berkeley National Laboratory is focused on the development of a high-brightness high-repetition rate (MHz-class) electron injector for X-ray FEL applications. The injector is based on a new concept gun, utilizing a normal conducting 186 MHz RF cavity operating in cw mode in conjunction with high quantum efficiency photocathodes capable of delivering the required repetition rates with available laser technology. The APEX activities are staged in 3 main phases. In Phases 0 and I, the gun will be tested at its nominal energy of 750 keV and several different photocathodes are tested at full repetition rate. In Phase II, a pulsed linac will be added for accelerating the beam at several tens of MeV to reduce space charge effects and measure the high-brightness performance of the gun when integrated in an injector scheme. At Phase II energies, the radiation shielding configuration of APEX limits the repetition rate to a maximum of several Hz. Phase 0 is under commissioning, Phase I under installation, and initial activities for Phase II are underway. This paper presents an update on the status of these activities.

WEPPP073	Dynamic Feedback Model for High Repetition Rate Linac-driven FELs	2879
	J.M. Byrd, L.R. Doolittle, P. Emma, G. Huang, A. Ratti, C. Serrano LBNL, Berkeley, California, USA
	Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. One of the concepts for the next generation of linac-driven FELs is a cw superconducting linac driving an electron beam with MHz repetition rates. One of the challenges for next generation FELs is improve the shot-to-shot stability of the energy, charge, peak current, and timing jitter of the electron beam. The use of a cw RF system with MHz beam repetition rates presents an opportunity to use broadband feedback to stabilize the beam parameters. To understand the performance of such a feedback system, we are are developing a dynamic feedback model of the machine with a focus on the longitudinal beam properties. The model is being developed as an extension of the LITrack code and will include the dynamics of the beam-cavity interaction, RF feedback, beam-based feedback, and multibunch effects. In this paper, we will present the status of this model along with results.

WEPPR031	Injector Beam Dynamics for a High-repetition Rate 4th-generation Light Source	3000
	C. F. Papadopoulos, J.N. Corlett, P. Emma, D. Filippetto, G. Penn, J. Qiang, M.W. Reinsch, F. Sannibale, C. Steier, M. Venturini, R.P. Wells LBNL, Berkeley, California, USA
	Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231. We report on the beam dynamics studies and optimization methods for a high-repetition (1 MHz) photoinjector based on a VHF normal conducting electron source. The simultaneous goals of beam compression and preservation of 6-dimensional beam brightness have to be achieved in the injector, in order to accommodate a linac driven FEL light source. For this, a parallel, multiobjective optimization algorithm is used. We discuss the relative merits of different injector design points, as well as the constraints imposed on the beam dynamics by technical considerations such as the high repetition rate.

WEYB02	Hard X-ray Self-seeding at the Linac Coherent Light Source
	P. Emma, J.W. Amann, F.-J. Decker, Y.T. Ding, Y. Feng, J.C. Frisch, D. Fritz, J.B. Hastings, Z. Huang, J. Krzywinski, H. Loos, A.A. Lutman, H.-D. Nuhn, D.F. Ratner, J.A. Rzepiela, S. Spampinati, D.R. Walz, J.J. Welch, J. Wu, D. Zhu SLAC, Menlo Park, California, USA W. Berg, R.R. Lindberg, D. Shu, Yu. Shvyd'ko, S. Stoupin, E. Trakhtenberg, A. Zholents ANL, Argonne, USA V.D. Blank, S. Terentiev TISNCM, Troitsk, Russia
	Funding: Work supported by US Department of Energy, contract number DE-AC02-76SF00515. We report on experimental results of FEL self-seeding with Angstrom wavelengths at the Linac Coherent Light Source (LCLS) at SLAC. The scheme, suggested at DESY, replaces the 16th 4-m long undulator segment (out of 33 total) with a weak magnetic chicane and a diamond-based monochromator in Bragg transmission geometry. The monochromatized SASE FEL pulse from the first half of the undulator line then seeds the second half. This demonstration of hard x-ray self-seeding is shown to narrow the FEL bandwidth by a factor 40-50, allows longitudinally coherent x-ray pulses near the Fourier-transform limit, and may eventually allow an increases in peak brightness by 1-2 orders of magnitude after applying an aggressive undulator field taper. G. Geloni, V. Kocharyan, E. Saldin, DESY 10-133, Aug. 2010.
	Slides WEYB02 [5.946 MB]