Author: AbbasiDavani, F.
Paper Title Page
MOPPC066 A Design of Thermionic Electron Gun for Traveling Wave Electron-linac in order to Inject Beam into Booster Synchrotron Accelerator 286
  • S. Ahmadian, F. AbbasiDavani, F. Ghasemi, M.Sh. Shafiee
    sbu, Tehran, Iran
  Applying computational codes functioning on the basis of methods such as Finite Integration caused the designing of different parts of an accelerator to be done faster and with more precision. The first step in using new software is the validation of these codes by experimental results, analytic relations or validating them against other codes whose validity has already been proved. This research aims to design an appropriate structure for thermionic electron gun of traveling wave electron-linac to be used to inject beam into synchrotron accelerators. Firstly, a simple structure of an electron gun used in TWT tube was simulated, and the parameters such as current, perveance, waist beam position, waist beam radius, beam radius entering anode aperture, and also the electric potential variation in the anode-cathode distance and the electric field of anode aperture were compared by experimental results and analytic relations. After verifying the software accuracy, a design for an electron gun with energy and current respectively 200 keV, 18 A and also initial beam radius of 8mm and minimum beam radius of 2.4 mm situated at the distance of 67.44mm from the cathode, was presented.  
TUPPR050 Design and simulation of Prebuncher for S-band Traveling Linear Accelerator 1930
  • S. Zarei, F. AbbasiDavani, S. Ahmadiannamini, F. Ghasemi
    sbu, Tehran, Iran
  • H. Shaker
    IPM, Tehran, Iran
  An S-band Traveling wave linear accelerator with an RF input peak power level up to 2.5 MW, for accelerating 1 mA beam of electron up to 15 MeV, is under construction in Iran. This article presents design procedure of a prebuncher for this accelerator. One standing-cavity type prebuncher is required for bunching electron beam for this accelerator. The intended prebuncher is driven by a coaxial line at 2 kW and operated at the same frequency of the other parts of the accelerator. The magnetic coupling applied has been applied for power coupling to the prebuncher cavity. The optimum dimensions of the prebuncher were obtained by using 2D and 3D electromagnetic codes in the frequency domain. Prebuncher cavity consists of a copper body and coupling loop feed.  
WEPPD063 Construction of Disk-loaded Buncher for S-Band Low Energy TW Electron Linear Accelerator 2666
  • F. Ghasemi, F. AbbasiDavani, S. Ahmadiannamini, M.Sh. Shafiee
    sbu, Tehran, Iran
  • M.L. Lamehi Rashti, H. Shaker
    IPM, Tehran, Iran
  The project of design and construction of Traveling linear electron accelerator is being performed by the Institute for Research in Fundamental Sciences (IPM) and Shahid Beheshti University in Iran. By using the results of the calculations and by dynamic simulation of electron beam in the designed buncher, the dimensions of the designed sample have been obtained. This paper discuss construction of this buncher.  
THPPD070 Design of High Power Pulse Modulator for Driving of Twystron used in S-band Linear Accelerator 3674
  • V. Aslani, F. AbbasiDavani, F. Ghasemi, M.Sh. Shafiee
    sbu, Tehran, Iran
  This design related to an s-band linear accelerator that the main tube and buncher of it have been made. RF power supply is used in this accelerator tube made up of a Twystron with 2.5 MW peak power and frequency band width 2.9~3.1 GHz. This paper offers the design of modulator for this RF amplifier. This modulator design uses solid-state method and is under construction with specification of ; Adjustable voltage from 0 to 120 kV, adjustable pulse width 2 until7μsecond, adjustable repetition rate 80-120 Hz ,ripple less than0.25% and efficiency up 80 percent. This system designed with series of 6 modules that each of them provides 5kV and IGBT switches that transform the voltage on the pulse transformer.