Paper |
Title |
Page |
MOCZB1 |
A Picosecond Sampling Electronic “KAPTURE” for Terahertz Synchrotron Radiation |
24 |
|
- C.M. Caselle, M. Brosi, S.A. Chilingaryan, T. Dritschler, N. Hiller, V. Judin, A. Kopmann, A.-S. Müller, L. Petzold, J. Raasch, L. Rota, M. Siegel, N.J. Smale, J.L. Steinmann, M. Vogelgesang, M. Weber, S. Wuensch
KIT, Karlsruhe, Germany
|
|
|
For a few years, coherent synchrotron radiation (CSR) generated by short electron bunches has been provided at the ANKA light source. Electron bunches can be filled in up to 184 buckets with a distance between two adjacent bunches of 2 ns corresponding to the RF system frequency of 500 MHz. Arbitrary filling patterns are generated to investigate the interaction of adjacent bunches in CSR. To study the THz emission characteristics over multiple revolutions superconducting YBa2Cu3O7−δ (YBCO) film detectors are used. The intrinsic response time of YBCO thin films is in the order of a few picoseconds only. For fast, continuous sampling of these individual ultra-short terahertz pulses, a novel digitizer system has been developed. The KAPTURE (KArlsruhe Pulse Taking Ultra-fast Readout Electronics) consists of a wideband low-noise amplifier, a picosecond pulse sampling card and a GByte transfer data link back-end readout card. High-end graphic processing units (GPUs) perform real-time data analysis. The KAPTURE system was successfully demonstrated for readout of the intensity fluctuations in the CSR at the ANKA Storage Ring detected in THz range. Four samples are recorded in parallel for each fast pulse with programmable sampling times in the range of 3 to 100 psec. A clean jitter phase locked loop (PLL) provides a clock signal with high temporal accuracy. The back-end card receives the 4 digital samples every 2 ns with 12 bits resolution and transmits the data to the data analysis unit. The readout board is based on programmable logic FPGA and DDR3 memories for on-line data preprocessing and temporary storage. The data is transmitted to the GPU computing node by a fast data transfer links based on a bus master DMA engine connected to PCI express endpoint logic to ensure a continuous high data throughput of up to 4 GByte/s. This heterogeneous real-time system architecture based on FPGA and GPU is used for on-line pulse reconstruction and evaluations and calculates the peak amplitude of each pulse and the time between consecutive bunches with a picosecond time resolution. A Fast Fourier Transform (FFT) is performed on-line for the frequency analysis of the CSR undulations. With the presented acquisition system it was possible to resolve the bursting behavior of single bunches even in a multi-bunch environment to study the bunch-bunch-interactions at ANKA. First results obtained have already been published in the synchrotron machine physic community. The monitoring of bursting for different ANKA parameters using KAPTURE system opens up new analysis and diagnostics possibilities for electron storage rings operating at short bunch lengths.
|
|
|
Slides MOCZB1 [11.326 MB]
|
|
Export • |
reference for this paper to
※ LaTeX,
※ Text,
※ IS/RefMan,
※ EndNote (xml)
|
|
|
TUPD10 |
An Ultrafast Linear Array Detector for Single-Shot Electro-Optical Bunch Profile Measurements |
435 |
|
- L. Rota, C.M. Caselle, N. Hiller, A.-S. Müller, M. Weber
KIT, Karlsruhe, Germany
|
|
|
A new spectrometer system has been developed at ANKA for near-field single-shot Electro-Optical (EO) bunch profile measurements with a frame rate of 5 Mfps. The frame rate of commercial line detectors is limited to several tens of kHz, unsuitable for measuring fast dynamic changes of the bunch conditions. The new system aims to realize continuous data acquisition and over long observation periods without dead time. InGaAs or Si linear array pixel sensors are used to detect the near IR and visible spectrum radiation. The detector signals are fed via wire-bonding connections to the GOTTHARD ASIC, a charge-sensitive amplifier with analog outputs. The front-end board is also equipped with an array of fast ADCs. The digital samples are then acquired by an FPGA-based readout card and transmitted to an external DAQ system via a high-speed PCI-Express data link. The DAQ system uses high-end Graphics Processors Units (GPUs) to perform a real-time analysis of the beam conditions. In this paper we present the concept, the first prototype and the low-noise layout techniques used for fast linear detectors.
|
|
|
Poster TUPD10 [5.159 MB]
|
|
Export • |
reference for this paper to
※ LaTeX,
※ Text,
※ IS/RefMan,
※ EndNote (xml)
|
|
|