FEL2013 - List of Authors (Ischebeck, R.)

Paper

Title

Page

Slice Emittance Optimization at the SwissFEL Injector Test Facility

200

E. Prat, M. Aiba, S. Bettoni, B. Beutner, M.W. Guetg, R. Ischebeck, S. Reiche, T. Schietinger
PSI, Villigen PSI, Switzerland

Slice emittance measurements in the SwissFEL injector test facility have demonstrated emittances for the 10pC-200pC bunch charges which are well below the tight requirements of SwissFEL. Results, emittance tuning strategy and measurement methods are reported.

Slides TUOCNO06 [0.537 MB]

TUPSO14

Transverse Deflecting Structures for Bunch Length and Slice Emittance Measurements on SwissFEL

236

P. Craievich, R. Ischebeck, F. Löhl, G.L. Orlandi, E. Prat
PSI, Villigen PSI, Switzerland

The SwissFEL project, under development at the Paul Scherrer Institut, will produce FEL radiation in a wavelength range from 0.1 nm to 7 nm. The facility consists of an S-band rf-gun and booster, and a C-band main linac which accelerates the beam up to 5.8 GeV. Two magnetic chicanes will compress the beam between 2.5 fs rms and 25 fs rms depending on the operation mode. The bunch length and slice parameters will be measured after the first bunch compressor (330 MeV) by using an S-band transverse deflecting structure (TDS). A C-band TDS will be employed to measure the longitudinal parameters of the beam just upstream the undulator beamline (5.8 GeV). With the designed transverse beam optics, an integrated deflecting voltage of 70 MV is required in order to achieve a longitudinal resolution on the femtosecond time scale. In this paper we present the TDS measurement systems to be used at SwissFEL, with a particular emphasis on the new C-band device, including hardware, lattice layout and beam optics.

Paper	Title	Page
TUOCNO06	Slice Emittance Optimization at the SwissFEL Injector Test Facility	200
	E. Prat, M. Aiba, S. Bettoni, B. Beutner, M.W. Guetg, R. Ischebeck, S. Reiche, T. Schietinger PSI, Villigen PSI, Switzerland
	Slice emittance measurements in the SwissFEL injector test facility have demonstrated emittances for the 10pC-200pC bunch charges which are well below the tight requirements of SwissFEL. Results, emittance tuning strategy and measurement methods are reported.
	Slides TUOCNO06 [0.537 MB]

TUPSO14	Transverse Deflecting Structures for Bunch Length and Slice Emittance Measurements on SwissFEL	236
	P. Craievich, R. Ischebeck, F. Löhl, G.L. Orlandi, E. Prat PSI, Villigen PSI, Switzerland
	The SwissFEL project, under development at the Paul Scherrer Institut, will produce FEL radiation in a wavelength range from 0.1 nm to 7 nm. The facility consists of an S-band rf-gun and booster, and a C-band main linac which accelerates the beam up to 5.8 GeV. Two magnetic chicanes will compress the beam between 2.5 fs rms and 25 fs rms depending on the operation mode. The bunch length and slice parameters will be measured after the first bunch compressor (330 MeV) by using an S-band transverse deflecting structure (TDS). A C-band TDS will be employed to measure the longitudinal parameters of the beam just upstream the undulator beamline (5.8 GeV). With the designed transverse beam optics, an integrated deflecting voltage of 70 MV is required in order to achieve a longitudinal resolution on the femtosecond time scale. In this paper we present the TDS measurement systems to be used at SwissFEL, with a particular emphasis on the new C-band device, including hardware, lattice layout and beam optics.