FEL2011 - List of Authors (Penn, G.)

Paper	Title	Page
MOPB32	System Trade Analysis for an FEL Facility	89
	M.W. Reinsch, B. Austin, J.N. Corlett, L.R. Doolittle, G. Penn, D. Prosnitz, J. Qiang, A. Sessler, M. Venturini, J.S. Wurtele LBNL, Berkeley, California, USA
	Designing an FEL from scratch requires the design team to balance multiple science needs, FEL and accelerator physics constraints and engineering limitations. STAFF (System Trade Analysis for an FEL Facility) enables the user to rapidly explore a large range of Linac and FEL design options. The model utilzes analytical models such as the Ming Xie formulas when appropriate and look-up tables when necessary to maintain speed, flexibility and extensiblity. STAFF allows for physics models for FEL harmonics, wake fields, cavity higher-order modes and aspects of linac particle dynamics. The code will permit the user to study error tolerances and multiple beamlines so as to explore the full capabilities of an entire user facility. This makes it possible to optimize the integrated system in terms of performance metrics such as photons/pulse, photons/sec and tunability range while ensuring that unrealistic requirements are not put on either the electron beam quality, undulator field/gap requirements or other system elements. This paper will describe preliminary results from STAFF as applied to a CW FEL soft X-ray facility.

MOPC14	Infrared Single Spike Pulses Generation Using a Short Period Superconducting Tape Undulator at APEX	129
	D. Filippetto, C. F. Papadopoulos, G. Penn, S. Prestemon, F. Sannibale LBNL, Berkeley, California, USA C. Pellegrini UCLA, Los Angeles, California, USA M. Yoon POSTECH, Pohang, Kyungbuk, Republic of Korea
	Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231 We report on the possibility of constructing an infrared FEL by combining a novel design super-conducting undulator developed at LBNL with the high brightness beam from the APEX injector facility at the Lawrence Berkeley National Laboratory. Calculations show that the resulting FEL is expected to deliver a saturated power of about a MW within a 4 m undulator length when operating in Self-Amplified-Spontaneus-Emission mode, with a single-spike of coherent radiation at 2 μm wavelength. The sub-cm undulator periods, associated with the relatively low energy of the APEX beam (20-25 MeV), forces the FEL to operate in a regime with unusual and interesting characteristics. The alternative option of laser seeding the FEL is also examined, showing the potential to reduce the saturation length even further.

TUPB12	Combined Optimization of a Linac-based FEL Light Source Using a Multiobjective Genetic Algorithm	283
	C. F. Papadopoulos, D. Filippetto, G. Penn, J. Qiang, F. Sannibale, M. Venturini LBNL, Berkeley, California, USA
	Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231 We report on the development status and preliminary results of a combined optimization scheme for a linac-based, high repetition rate, soft X-ray FEL. The underlying model includes the injector and linac parts of the machine, and the scheme will integrate the design process of these components toward the optimization of the FEL performance. For this, a parallel, multi-objective genetic algorithm is used. We also discuss the beam dynamics considerations that lead to the choices of objectives, or figure-of-merit beam parameters, and describe numerical solutions compatible with the requirements of a high repetition rate user facility.

WEPB02	Study of Highly Isochronous Beamlines for FEL Seeding	391
	C. Sun, H. Nishimura, G. Penn, M.W. Reinsch, D. Robin, F. Sannibale, C. Steier, W. Wan LBNL, Berkeley, California, USA
	Recently seeding schemes, such as ECHO for short (nm) wavelength FELs, have been proposed. These schemes require that the nm level longitudinal bunch structure be preserved over distance of several meters. This poses a challenge for the beamline design. In this paper we present our studies of several solutions for beamlines that are nearly isochronous.

THPB14	APEX Project Phase 0 and I Status and Plans and Activities for Phase II	582
	F. Sannibale, B.J. Bailey, K.M. Baptiste, J.M. Byrd, A.L. Catalano, D. Colomb, C.W. Cork, J.N. Corlett, S. De Santis, L.R. Doolittle, J. Feng, D. Filippetto, G. Huang, S. Kwiatkowski, W.E. Norum, H.A. Padmore, C. F. Papadopoulos, G. Penn, G.J. Portmann, S. Prestemon, J. Qiang, D.G. Quintas, J.W. Staples, M.E. Stuart, T. Vecchione, M. Venturini, M. Vinco, W. Wan, R.P. Wells, M.S. Zolotorev, F.A. Zucca LBNL, Berkeley, California, USA M. J. Messerly, M.A. Prantil LLNL, Livermore, California, USA C. Pellegrini UCLA, Los Angeles, California, USA M. Yoon POSTECH, Pohang, Kyungbuk, Republic of Korea
	Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231 The APEX project at the Lawrence Berkeley National Laboratory is devoted to the development of a high repetition rate (MHz-class) electron injector for X-ray FEL applications. The injector is based on a new concept photo-gun, utilizing a normal conducting 187 MHz RF cavity operating in CW mode in conjunction with high quantum efficiency photocathodes able to deliver the required repetition rates with available laser technology. The APEX activities are staged in two phases. In Phase I, the electron photo-gun is constructed, tested and several different photo-cathodes, such as alkali antimonides, Cs₂Te [1], diamond amplifiers [2], and metals, are tested at full repetition rate. In Phase II, a pulsed linac is added for accelerating the beam at several tens of MeV to prove the high brightness performance of the gun when integrated in an injector scheme. Based on funding availability, after Phase II, the program could also include testing of new undulator technologies and FEL studies. The status of Phase I, in its initial experimental phase, is described together with plans and activities for Phase II and beyond. [1] In collaboration with INFN-LASA, Milano, Italy. [2] In collaboration with Brookhaven National Laboratory, Upton NY, USA

Paper

Title

Page

System Trade Analysis for an FEL Facility

89

M.W. Reinsch, B. Austin, J.N. Corlett, L.R. Doolittle, G. Penn, D. Prosnitz, J. Qiang, A. Sessler, M. Venturini, J.S. Wurtele
LBNL, Berkeley, California, USA

Designing an FEL from scratch requires the design team to balance multiple science needs, FEL and accelerator physics constraints and engineering limitations. STAFF (System Trade Analysis for an FEL Facility) enables the user to rapidly explore a large range of Linac and FEL design options. The model utilzes analytical models such as the Ming Xie formulas when appropriate and look-up tables when necessary to maintain speed, flexibility and extensiblity. STAFF allows for physics models for FEL harmonics, wake fields, cavity higher-order modes and aspects of linac particle dynamics. The code will permit the user to study error tolerances and multiple beamlines so as to explore the full capabilities of an entire user facility. This makes it possible to optimize the integrated system in terms of performance metrics such as photons/pulse, photons/sec and tunability range while ensuring that unrealistic requirements are not put on either the electron beam quality, undulator field/gap requirements or other system elements. This paper will describe preliminary results from STAFF as applied to a CW FEL soft X-ray facility.

MOPC14

Infrared Single Spike Pulses Generation Using a Short Period Superconducting Tape Undulator at APEX

129

D. Filippetto, C. F. Papadopoulos, G. Penn, S. Prestemon, F. Sannibale
LBNL, Berkeley, California, USA
C. Pellegrini
UCLA, Los Angeles, California, USA
M. Yoon
POSTECH, Pohang, Kyungbuk, Republic of Korea

Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231
We report on the possibility of constructing an infrared FEL by combining a novel design super-conducting undulator developed at LBNL with the high brightness beam from the APEX injector facility at the Lawrence Berkeley National Laboratory. Calculations show that the resulting FEL is expected to deliver a saturated power of about a MW within a 4 m undulator length when operating in Self-Amplified-Spontaneus-Emission mode, with a single-spike of coherent radiation at 2 μm wavelength. The sub-cm undulator periods, associated with the relatively low energy of the APEX beam (20-25 MeV), forces the FEL to operate in a regime with unusual and interesting characteristics. The alternative option of laser seeding the FEL is also examined, showing the potential to reduce the saturation length even further.

TUPB12

Combined Optimization of a Linac-based FEL Light Source Using a Multiobjective Genetic Algorithm

283

C. F. Papadopoulos, D. Filippetto, G. Penn, J. Qiang, F. Sannibale, M. Venturini
LBNL, Berkeley, California, USA

Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231
We report on the development status and preliminary results of a combined optimization scheme for a linac-based, high repetition rate, soft X-ray FEL. The underlying model includes the injector and linac parts of the machine, and the scheme will integrate the design process of these components toward the optimization of the FEL performance. For this, a parallel, multi-objective genetic algorithm is used. We also discuss the beam dynamics considerations that lead to the choices of objectives, or figure-of-merit beam parameters, and describe numerical solutions compatible with the requirements of a high repetition rate user facility.

WEPB02

Study of Highly Isochronous Beamlines for FEL Seeding

391

C. Sun, H. Nishimura, G. Penn, M.W. Reinsch, D. Robin, F. Sannibale, C. Steier, W. Wan
LBNL, Berkeley, California, USA

Recently seeding schemes, such as ECHO for short (nm) wavelength FELs, have been proposed. These schemes require that the nm level longitudinal bunch structure be preserved over distance of several meters. This poses a challenge for the beamline design. In this paper we present our studies of several solutions for beamlines that are nearly isochronous.

THPB14

APEX Project Phase 0 and I Status and Plans and Activities for Phase II

582

F. Sannibale, B.J. Bailey, K.M. Baptiste, J.M. Byrd, A.L. Catalano, D. Colomb, C.W. Cork, J.N. Corlett, S. De Santis, L.R. Doolittle, J. Feng, D. Filippetto, G. Huang, S. Kwiatkowski, W.E. Norum, H.A. Padmore, C. F. Papadopoulos, G. Penn, G.J. Portmann, S. Prestemon, J. Qiang, D.G. Quintas, J.W. Staples, M.E. Stuart, T. Vecchione, M. Venturini, M. Vinco, W. Wan, R.P. Wells, M.S. Zolotorev, F.A. Zucca
LBNL, Berkeley, California, USA
M. J. Messerly, M.A. Prantil
LLNL, Livermore, California, USA
C. Pellegrini
UCLA, Los Angeles, California, USA
M. Yoon
POSTECH, Pohang, Kyungbuk, Republic of Korea

Funding: This work was supported by the Director of the Office of Science of the US Department of Energy under Contract no. DEAC02-05CH11231
The APEX project at the Lawrence Berkeley National Laboratory is devoted to the development of a high repetition rate (MHz-class) electron injector for X-ray FEL applications. The injector is based on a new concept photo-gun, utilizing a normal conducting 187 MHz RF cavity operating in CW mode in conjunction with high quantum efficiency photocathodes able to deliver the required repetition rates with available laser technology. The APEX activities are staged in two phases. In Phase I, the electron photo-gun is constructed, tested and several different photo-cathodes, such as alkali antimonides, Cs₂Te [1], diamond amplifiers [2], and metals, are tested at full repetition rate. In Phase II, a pulsed linac is added for accelerating the beam at several tens of MeV to prove the high brightness performance of the gun when integrated in an injector scheme. Based on funding availability, after Phase II, the program could also include testing of new undulator technologies and FEL studies. The status of Phase I, in its initial experimental phase, is described together with plans and activities for Phase II and beyond.
[1] In collaboration with INFN-LASA, Milano, Italy.
[2] In collaboration with Brookhaven National Laboratory, Upton NY, USA