IPAC2017 - List of Authors (Ortiz, E.)

Paper	Title	Page
TUPAB124	Development of the Manufacturing and QA Processes for the Magnetic Modules of the LCLS-II Soft X-Ray Undulators	1609
	K.L. Ray, D. Arbelaez, A.J. Band, D. Bianculli, A.P. Brown, J.N. Corlett, A.J. DeMello, J.R. Dougherty, L. Garcia Fajardo, K. Hanzel, D.E. Humphries, J.-Y. Jung, D. Leitner, M. Leitner, S. Marks, K.A. McCombs, D.V. Munson, D.A. Sadlier, D. Schlueter, E.J. Wallén, V. Waring, A. Zikmund LBNL, Berkeley, California, USA D.E. Bruch, A.L. Callen, G. Janša, D.S. Martinez-Galarce, H.-D. Nuhn, E. Ortiz, Ž. Oven, M. Rowen, Z.R. Wolf SLAC, Menlo Park, California, USA
	Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231. A new free electron laser being built at SLAC National Accelerator Laboratory, the Linear Coherent Light Source II (LCLS-II), will use 21 soft x-ray undulators (SXR) and 32 hard x-ray undulators (HGVPU). Lawrence Berkeley National Laboratory (LBNL) is responsible for the design and manufacturing of all variable-gap, hybrid permanent-magnet undulators. The physics requirements for the undulators specify a longitudinal pole misalignment maximum rms error of 25 μm and a vertical pole misalignment maximum error of 50 μm. In addition, magnet positioning critically influences the gap-dependent field properties due to saturation effects at the smallest operational gaps. This paper discusses the manufacturing and QA methods developed to carefully control the longitudinal and vertical pole and magnet positions during undulator production. Inspection results are discussed based on data gathered during construction of a prototype as well as pre-production soft x-ray undulator.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-TUPAB124
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Development of the Manufacturing and QA Processes for the Magnetic Modules of the LCLS-II Soft X-Ray Undulators

1609

K.L. Ray, D. Arbelaez, A.J. Band, D. Bianculli, A.P. Brown, J.N. Corlett, A.J. DeMello, J.R. Dougherty, L. Garcia Fajardo, K. Hanzel, D.E. Humphries, J.-Y. Jung, D. Leitner, M. Leitner, S. Marks, K.A. McCombs, D.V. Munson, D.A. Sadlier, D. Schlueter, E.J. Wallén, V. Waring, A. Zikmund
LBNL, Berkeley, California, USA
D.E. Bruch, A.L. Callen, G. Janša, D.S. Martinez-Galarce, H.-D. Nuhn, E. Ortiz, Ž. Oven, M. Rowen, Z.R. Wolf
SLAC, Menlo Park, California, USA

Funding: Work supported by the Director, Office of Science, of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231.
A new free electron laser being built at SLAC National Accelerator Laboratory, the Linear Coherent Light Source II (LCLS-II), will use 21 soft x-ray undulators (SXR) and 32 hard x-ray undulators (HGVPU). Lawrence Berkeley National Laboratory (LBNL) is responsible for the design and manufacturing of all variable-gap, hybrid permanent-magnet undulators. The physics requirements for the undulators specify a longitudinal pole misalignment maximum rms error of 25 μm and a vertical pole misalignment maximum error of 50 μm. In addition, magnet positioning critically influences the gap-dependent field properties due to saturation effects at the smallest operational gaps. This paper discusses the manufacturing and QA methods developed to carefully control the longitudinal and vertical pole and magnet positions during undulator production. Inspection results are discussed based on data gathered during construction of a prototype as well as pre-production soft x-ray undulator.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2017-TUPAB124

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)