FEL2014 - List of Authors (Li, R.K.)

Paper	Title	Page
THP042	The LCLS-II Injector Design	815
	J.F. Schmerge, A. Brachmann, D. Dowell, A.R. Fry, R.K. Li, Z. Li, T.O. Raubenheimer, T. Vecchione, F. Zhou SLAC, Menlo Park, California, USA A.C. Bartnik, I.V. Bazarov, B.M. Dunham, C.M. Gulliford, C.E. Mayes Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA D. Filippetto, R. Huang, C. F. Papadopoulos, G.J. Portmann, J. Qiang, F. Sannibale, S.P. Virostek, R.P. Wells LBNL, Berkeley, California, USA A. Lunin, N. Solyak, A. Vivoli Fermilab, Batavia, Illinois, USA
	The new LCLS-II project will construct a 4 GeV continuous wave (CW) superconducting linear accelerator to simultaneously feed two undulators which will cover the spectral ranges 0.2-1.2 keV and 1-5 keV, respectively. The injector must provide up to 300 pC/bunch with a normalized emittance < 0.6 mm and peak current > 30 A at up to 1 MHz repetition rate. An electron gun with the required brightness at such high repetition rate has not yet been demonstrated. However, several different options have been explored with results that meet or exceed the performance requirements of LCLS-II. The available technologies for high repetition-rate guns, and the need to keep dark current within acceptable values, limit the accelerating gradient in the electron gun. We propose a CW normal conducting low frequency RF gun for the electron source due to a combination of the simplicity of operation and the highest achieved gradient in a CW gun, potentially allowing for lower beam emittances. The high gradient is especially significant at the 300 pC/bunch charge where beam quality can suffer due to space charge. This paper describes the design challenges and presents our solutions for the LCLS-II injector.

Paper

Title

Page

The LCLS-II Injector Design

815

J.F. Schmerge, A. Brachmann, D. Dowell, A.R. Fry, R.K. Li, Z. Li, T.O. Raubenheimer, T. Vecchione, F. Zhou
SLAC, Menlo Park, California, USA
A.C. Bartnik, I.V. Bazarov, B.M. Dunham, C.M. Gulliford, C.E. Mayes
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
D. Filippetto, R. Huang, C. F. Papadopoulos, G.J. Portmann, J. Qiang, F. Sannibale, S.P. Virostek, R.P. Wells
LBNL, Berkeley, California, USA
A. Lunin, N. Solyak, A. Vivoli
Fermilab, Batavia, Illinois, USA

The new LCLS-II project will construct a 4 GeV continuous wave (CW) superconducting linear accelerator to simultaneously feed two undulators which will cover the spectral ranges 0.2-1.2 keV and 1-5 keV, respectively. The injector must provide up to 300 pC/bunch with a normalized emittance < 0.6 mm and peak current > 30 A at up to 1 MHz repetition rate. An electron gun with the required brightness at such high repetition rate has not yet been demonstrated. However, several different options have been explored with results that meet or exceed the performance requirements of LCLS-II. The available technologies for high repetition-rate guns, and the need to keep dark current within acceptable values, limit the accelerating gradient in the electron gun. We propose a CW normal conducting low frequency RF gun for the electron source due to a combination of the simplicity of operation and the highest achieved gradient in a CW gun, potentially allowing for lower beam emittances. The high gradient is especially significant at the 300 pC/bunch charge where beam quality can suffer due to space charge. This paper describes the design challenges and presents our solutions for the LCLS-II injector.