NAPAC2019 - List of Authors (Bender, T.J.)

Paper	Title	Page
TUPLS02	APS Upgrade Insertion Device Vacuum Chamber Design	450
	J.E. Lerch, T.J. Bender, O.K. Mulvany, M.E. Szubert ANL, Lemont, Illinois, USA
	A straight section vacuum system (nominally 5.363 meters long) has been designed for the APS upgrade project. This vacuum system will be used in straight sections equipped with hybrid permanent magnet undulators (HPMU). The vacuum system assembly consists of the insertion device vacuum chamber (IDVC), the vacuum chamber distributed support, and the photon absorber. Numerous functional requirements constrained the IDVC design. These constraints included incorporation of the beam aperture transition into the end of the aluminium vacuum chamber extrusion (storage ring aperture to IDVC aperture), thin walls (~600 microns) surrounding the beam aperture to allow for as small a magnetic gap as possible, and complicated weld paths to ensure a continuous beam surface to minimize impedance. Additionally, extensive FEA and raytrace analysis were performed to ensure that the chamber would not fail due to structural or thermal perturbations.
	Poster TUPLS02 [3.816 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-TUPLS02
About •	paper received ※ 26 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPLS03	Advanced Photon Source Upgrade	453
	M.E. Szubert, E.R. Anliker, T.J. Bender, J.E. Lerch ANL, Lemont, Illinois, USA
	The Advanced Photon Source Upgrade (APS-U) in-cludes four straight sections equipped with full length Superconducting Undulators (SCUs). These sections require vacuum systems that must span 5.383 meters at nominal length, accommodate the SCU device, and ac-commodate additional magnets for the canted configura-tions. In the direction of the beam, the upstream portion of the vacuum system is a copper chamber doubling as a photon absorber with a design that is manufactured to allow a 13.5 mm canting magnet gap. This portion of the vacuum system operates at room temperature and shad-ows the length of the vacuum chamber that operates within the cryostat at 20K. The vacuum chamber inside the cryostat is a weldment including a machined alumi-num extrusion allowing for an 8mm magnetic gap, stain-less steel thermal insulators, copper shields, and bel-lows/flange assembly. The vacuum system includes an-other room temperature copper chamber and absorber on the downstream end of the straight section. The vacuum system provides Ultra-high Vacuum (UHV) continuity through the straight section, connecting the storage ring vacuum systems.
	Poster TUPLS03 [0.974 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-TUPLS03
About •	paper received ※ 26 August 2019 paper accepted ※ 13 September 2019 issue date ※ 08 October 2019
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

APS Upgrade Insertion Device Vacuum Chamber Design

450

J.E. Lerch, T.J. Bender, O.K. Mulvany, M.E. Szubert
ANL, Lemont, Illinois, USA

A straight section vacuum system (nominally 5.363 meters long) has been designed for the APS upgrade project. This vacuum system will be used in straight sections equipped with hybrid permanent magnet undulators (HPMU). The vacuum system assembly consists of the insertion device vacuum chamber (IDVC), the vacuum chamber distributed support, and the photon absorber. Numerous functional requirements constrained the IDVC design. These constraints included incorporation of the beam aperture transition into the end of the aluminium vacuum chamber extrusion (storage ring aperture to IDVC aperture), thin walls (~600 microns) surrounding the beam aperture to allow for as small a magnetic gap as possible, and complicated weld paths to ensure a continuous beam surface to minimize impedance. Additionally, extensive FEA and raytrace analysis were performed to ensure that the chamber would not fail due to structural or thermal perturbations.

Poster TUPLS02 [3.816 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-TUPLS02

About •

paper received ※ 26 August 2019 paper accepted ※ 31 August 2019 issue date ※ 08 October 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPLS03

Advanced Photon Source Upgrade

453

M.E. Szubert, E.R. Anliker, T.J. Bender, J.E. Lerch
ANL, Lemont, Illinois, USA

The Advanced Photon Source Upgrade (APS-U) in-cludes four straight sections equipped with full length Superconducting Undulators (SCUs). These sections require vacuum systems that must span 5.383 meters at nominal length, accommodate the SCU device, and ac-commodate additional magnets for the canted configura-tions. In the direction of the beam, the upstream portion of the vacuum system is a copper chamber doubling as a photon absorber with a design that is manufactured to allow a 13.5 mm canting magnet gap. This portion of the vacuum system operates at room temperature and shad-ows the length of the vacuum chamber that operates within the cryostat at 20K. The vacuum chamber inside the cryostat is a weldment including a machined alumi-num extrusion allowing for an 8mm magnetic gap, stain-less steel thermal insulators, copper shields, and bel-lows/flange assembly. The vacuum system includes an-other room temperature copper chamber and absorber on the downstream end of the straight section. The vacuum system provides Ultra-high Vacuum (UHV) continuity through the straight section, connecting the storage ring vacuum systems.

Poster TUPLS03 [0.974 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-NAPAC2019-TUPLS03

About •

paper received ※ 26 August 2019 paper accepted ※ 13 September 2019 issue date ※ 08 October 2019

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)