IPAC2018 - List of Authors (Yang, B.X.)

Paper	Title	Page
TUZGBD3	Beam Diagnostics for the APS MBA Upgrade	1204
	N. Sereno, N.D. Arnold, R.W. Blake, A.R. Brill, H. Bui, J. Carwardine, G. Decker, L. Emery, T. Fors, P.S. Kallakuri, R.T. Keane, R.M. Lill, D.R. Paskvan, A.F. Pietryla, H. Shang, X. Sun, S. Veseli, J. Wang, S. Xu, B.X. Yang ANL, Argonne, Illinois, USA
	The Advanced Photon Source (APS) is currently in the preliminary design phase for a multi-bend acromat (MBA) lattice upgrade. Beam stability is critical where the requirements are driven from the beam size which is expected to approach 4 microns vertically at the insertion device (ID) source points. AC rms beam stability requirements are defined as 10 % the minimum source size at the ID in the band 0.01-1000 Hz. The vertical plane stability goal is the most ambitious requiring a stability of 400 nm at the ID source point. In addition, long term drift defined as motion over a seven day timescale can be no more than 1 micron. In order to achieve these demanding beam stability requirements, a suite of beam diagnostics will be required including rf BPMs, X-ray BPMs, a mechanical motion measurement system, beam size monitors and a real time orbit feedback system. In addition, a tune measurement system, transverse multi-bunch feedback system and current monitors are planned for the upgrade. We report on the beam diagnostics design and APS storage ring R&D results used to inform the design.
	Slides TUZGBD3 [16.748 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD3
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAF006	Fast Photodetector Bunch Duration Monitor for the Advanced Photon Source Particle Accumulator Ring	1819
	J.C. Dooling, J.R. Calvey, K.C. Harkay, B.X. Yang, C. Yao ANL, Argonne, Illinois, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. A fast photodetector is used to monitor the bunch duration in the Advanced Photon Source (APS) Particle Accumulator Ring (PAR). The Bunch Duration Monitor (BDM) diagnostic provides an accurate measure of the PAR bunch length. PAR BDM data show good agreement with streak camera measurements. The BDM is based on the metal-semiconductor-metal (MSM) photodetector Hamamatsu G4176-03 MSM with specified rise and fall times of 30 ps. The BDM has sufficient frequency response to resolve the PAR bunch near extraction where, under low-charge conditions, minimum rms pulse durations of 200-300 ps are observed. Beam from the PAR is injected into the Booster; for efficient capture, injected rms bunch duration from the PAR must be less than 600 ps. The MSM detector exhibits a ringing response to fast input signals. To overcome this, the BDM output is de-convolved with the impulse response function of the detector-amplifier circuit. Turn-by-turn bunch duration data is presented versus charge and time in the PAR cycle. Charge calibration is used to determine fit parameters for bunch duration measurements in peak-detection mode. Observations relevant to APS Upgrade high-charge studies are presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAF006
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Beam Diagnostics for the APS MBA Upgrade

1204

N. Sereno, N.D. Arnold, R.W. Blake, A.R. Brill, H. Bui, J. Carwardine, G. Decker, L. Emery, T. Fors, P.S. Kallakuri, R.T. Keane, R.M. Lill, D.R. Paskvan, A.F. Pietryla, H. Shang, X. Sun, S. Veseli, J. Wang, S. Xu, B.X. Yang
ANL, Argonne, Illinois, USA

The Advanced Photon Source (APS) is currently in the preliminary design phase for a multi-bend acromat (MBA) lattice upgrade. Beam stability is critical where the requirements are driven from the beam size which is expected to approach 4 microns vertically at the insertion device (ID) source points. AC rms beam stability requirements are defined as 10 % the minimum source size at the ID in the band 0.01-1000 Hz. The vertical plane stability goal is the most ambitious requiring a stability of 400 nm at the ID source point. In addition, long term drift defined as motion over a seven day timescale can be no more than 1 micron. In order to achieve these demanding beam stability requirements, a suite of beam diagnostics will be required including rf BPMs, X-ray BPMs, a mechanical motion measurement system, beam size monitors and a real time orbit feedback system. In addition, a tune measurement system, transverse multi-bunch feedback system and current monitors are planned for the upgrade. We report on the beam diagnostics design and APS storage ring R&D results used to inform the design.

Slides TUZGBD3 [16.748 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD3

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAF006

Fast Photodetector Bunch Duration Monitor for the Advanced Photon Source Particle Accumulator Ring

1819

J.C. Dooling, J.R. Calvey, K.C. Harkay, B.X. Yang, C. Yao
ANL, Argonne, Illinois, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
A fast photodetector is used to monitor the bunch duration in the Advanced Photon Source (APS) Particle Accumulator Ring (PAR). The Bunch Duration Monitor (BDM) diagnostic provides an accurate measure of the PAR bunch length. PAR BDM data show good agreement with streak camera measurements. The BDM is based on the metal-semiconductor-metal (MSM) photodetector Hamamatsu G4176-03 MSM with specified rise and fall times of 30 ps. The BDM has sufficient frequency response to resolve the PAR bunch near extraction where, under low-charge conditions, minimum rms pulse durations of 200-300 ps are observed. Beam from the PAR is injected into the Booster; for efficient capture, injected rms bunch duration from the PAR must be less than 600 ps. The MSM detector exhibits a ringing response to fast input signals. To overcome this, the BDM output is de-convolved with the impulse response function of the detector-amplifier circuit. Turn-by-turn bunch duration data is presented versus charge and time in the PAR cycle. Charge calibration is used to determine fit parameters for bunch duration measurements in peak-detection mode. Observations relevant to APS Upgrade high-charge studies are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAF006

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)