BNL, Upton, Long Island, New York, USA
LBNL, Berkeley, California, USA
In the present design of the future electron-ion collider eRHIC at the Brookhaven National Laboratory, a crossing angle of 22~mrad between the electron and proton orbits at the interaction region is adopted. To compensate the geometric luminosity loss, a local compensation scheme with two sets of crab cavities for each beam is considered. In this article, we first carry out strong-strong beam-beam simulation to study possible coherent beam-beam instability. Under the assumption of no coherent beam-beam motion, we then carry out a weak-strong beam-beam simulation to determine the long-term stability of the proton beam with the equilibrium electron beam sizes extracted from the strong-strong beam-beam simulation.
BNL, Upton, Long Island, New York, USA
Tech-X, Boulder, Colorado, USA
We have refined the design for the Rapid Cycling Synchrotron (RCS) polarized electron injector for eRHIC. The newer design includes bypasses for the eRHIC detectors and definition of the lattice layout in the existing RHIC tunnel. Additionally, we provide more details on the RF, alignment and orbit control, and magnet specifications.
BNL, Upton, Long Island, New York, USA
Fermilab, Batavia, Illinois, USA
The electron-ion collider eRHIC aims at a luminosity around 1034cm-2sec-1, using strong cooling of the hadron beam. Since the required cooling techniques are not yet readily available, an initial version with a peak luminosity of 3*1033cm-2sec-1 is being developed that can later be outfitted with strong hadron cooling. We will report on the current design status and the envisioned path towards 1034cm-2sec-1 luminosity.
Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
BNL, Upton, Long Island, New York, USA
JLab, Newport News, Virginia, USA
Cockcroft Institute, Warrington, Cheshire, United Kingdom
Cornell University, Ithaca, New York, USA
STFC/RAL/ASTeC, Chilton, Didcot, Oxon, United Kingdom
HZB, Berlin, Germany
A collaboration between Cornell University and Brookhaven National Laboratory has designed and is constructing CBETA, the Cornell-BNL ERL Test Accelerator on the Cornell campus. The ERL technology that has been prototyped at Cornell for many years is being used for this new accelerator, including a DC electron source and an SRF injector Linac with world-record current and normalized brightness in a bunch train, a high-current linac cryomodule optimized for ERLs, a high-power beam stop, and several diagnostics tools for high-current and high-brightness beams. BNL has designed multi-turn ERLs for several purpose, dominantly for the electron beam of eRHIC, its Electron Ion Collider (EIC) project and for the associated fast electron cooling system. Also in JLEIC, the EIC designed at JLAB, an ERL is envisioned to be used for electron cooling. The number of transport lines in an ERL is minimized by using return arcs that are comprised of a Fixed Field Alternating-gradient (FFA) design. This technique will be tested in CBETA, which has a single return for the 4-beam energies with strongly-focusing permanent magnets of Halbach type. The high-brightness beam with 150~MeV and up to 40~mA will have applications beyond accelerator research, in industry, in nuclear physics, and in X-ray science. Low current electron beam has already been sent through the most relevant parts of CBETA, from the DC gun through both cryomodules, through one of the 8 similar separator lines, and through one of the 27 similar FFA structures. Further construction is envisioned to lead to a commissioning start for the full system early in 2019.
BNL, Upton, Long Island, New York, USA
The impedance budget for the eRHIC project is discussed at its earlier stage of development. As a first step, with the eRHIC lattice and beam parameters , we use the geometric impedances of the vacuum chamber components simulated for the NSLS-II project. The impedance budged will be updated next with more impedance data simulated for the optimized eRHIC vacuum components. It will allows us to keep track on the collective effects changes with more realistic components added to the ring.
BNL, Upton, Long Island, New York, USA
The electron-ion collider eRHIC requires a variety of kickers and septa for injection and extraction of beams throughout the entire collider complex. We plan to use pulsed systems for beam injection and extraction in Electron RCS, Electron Storage Ring, and Hadron ring. In this paper, we describe the pulsed systems required for beam transfer in the eRHIC Ring-Ring Pre-conceptual Design. We will outline the parameter ranges, technology choices, and opportunities for research and development in pulsed power technology.