IPAC2018 - List of Authors (Shchegolkov, D.Y.)

Paper	Title	Page
THPAL024	A Simple Variable Focus Lens for Field Emitter Cathodes	3677
	R.L. Fleming, H.L. Andrews, K. Bishofberger, D. Kim, J.W. Lewellen, K.E. Nichols, D.Y. Shchegolkov, E.I. Simakov LANL, Los Alamos, New Mexico, USA
	Funding: Los Alamos National Laboratory LDRD Program We present the design for a simple, variable-focus solenoidal lens with integrated emittance filtering. The design was developed as a first-iteration injection optics solution for transport of a beam from a field-emitter cathode into a dielectric laser accelerator structure. The design is easy to fabricate and, while based on permanent magnets, can readily be modified to allow for remote control of the focal length. The emittance is controlled via selection of collimating irises. The focal length can be changed by altering the spacing between two permanent ring magnets. Results from fabrication and initial testing will be presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL024
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPML007	An Investigation of Electron Beam Divergence from a Single DFEA Emitter Tip	4662
	H.L. Andrews, B.K. Choi, R.L. Fleming, D. Kim, J.W. Lewellen, K.E. Nichols, D.Y. Shchegolkov, E.I. Simakov LANL, Los Alamos, New Mexico, USA
	Funding: We gratefully acknowledge the support of the U.S. Department of Energy through the LANL/LDRD Program for this work. Diamond Field-Emitter Array (DFEA) cathodes are arrays of micron-scale diamond pyramids with nanometer-scale tips. DFEAs can produce high emission currents with small emittance and energy spread. At LANL, we have an ongoing program to test DFEA cathodes for the purpose of using them to generate high-current, low-emittance electron beams for dielectric laser accelerators. We have recently upgraded our cathode test chamber to use a mesh anode in place of a solid luminescent anode. In addition to allowing for downstream beam transport, this arrangement may eliminate earlier problems with reduced cathode performance due to ion back-bombardment. We are measuring divergence of the electron beam past the mesh in an effort to characterize the inherent beam divergence off the diamond tip and divergence contribution from the mesh. We will compare these observations with theoretical and modeled values.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPML007
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPML010	Modeling of Diamond Field Emitter Arrays for Shaped Electron Beam Production	4668
	K.E. Nichols, H.L. Andrews, D.Y. Shchegolkov, E.I. Simakov LANL, Los Alamos, New Mexico, USA
	We present simulations of shaped electron beam production from diamond field emitter array (DFEA) cathodes. DFEAs are arrays of diamond pyramids with bases of the order of 10 microns that produce high current densities. These arrays can be fabricated in arbitrary shapes such as a triangle or a double triangle, so that they produce an inherently shaped beam. These transversely shaped beams can be put through an emittance exchanger to produce a longitudinally shaped electron beam distribution for use with high-transformer ratio wakefield accelerators. Simulations are conducted with MICHELLE. We design cathodes and focusing systems that preserve the beam's shape while transporting it to the emittance exchanger.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPML010
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPML011	Possibilities for Fabricating Polymer Dielectric Laser Accelerator Structures with Additive Manufacturing	4671
	E.I. Simakov, R.D. Gilbertson, M.J. Herman, G. Pilania, D.Y. Shchegolkov, E.M. Walker, E. Weis LANL, Los Alamos, New Mexico, USA R.J. England, K.P. Wootton SLAC, Menlo Park, California, USA
	Funding: Los Alamos National Laboratory LDRD Program We present results of recent studies of new materials designed for the additive manufacturing of accelerating structures for dielectric laser accelerators (DLAs). Demonstration of a stand-alone practical DLA requires innovation in design and fabrication of efficient laser accelerator structures and couplers. Many complicated three-dimensional structures for laser acceleration (such as a long woodpile structure with couplers) are difficult to manufacture with conventional microfabrication technologies. LANL has a large effort focused on developing new materials and techniques for additive manufacturing. The materials for DLA structures must have high dielectric constant (larger than 4), low loss in the infrared regime, high laser damage threshold, and be able to withstand the electron beam damage. This presentation will discuss the development of novel infrared dielectric materials that are of interest for laser acceleration and are compatible with additive manufacturing, as well as recent advances in additive manufacturing of dielectric woodpile structures using a Nanoscribe direct laser-writing 3D printer.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPML011
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

A Simple Variable Focus Lens for Field Emitter Cathodes

3677

R.L. Fleming, H.L. Andrews, K. Bishofberger, D. Kim, J.W. Lewellen, K.E. Nichols, D.Y. Shchegolkov, E.I. Simakov
LANL, Los Alamos, New Mexico, USA

Funding: Los Alamos National Laboratory LDRD Program
We present the design for a simple, variable-focus solenoidal lens with integrated emittance filtering. The design was developed as a first-iteration injection optics solution for transport of a beam from a field-emitter cathode into a dielectric laser accelerator structure. The design is easy to fabricate and, while based on permanent magnets, can readily be modified to allow for remote control of the focal length. The emittance is controlled via selection of collimating irises. The focal length can be changed by altering the spacing between two permanent ring magnets. Results from fabrication and initial testing will be presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL024

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPML007

An Investigation of Electron Beam Divergence from a Single DFEA Emitter Tip

4662

H.L. Andrews, B.K. Choi, R.L. Fleming, D. Kim, J.W. Lewellen, K.E. Nichols, D.Y. Shchegolkov, E.I. Simakov
LANL, Los Alamos, New Mexico, USA

Funding: We gratefully acknowledge the support of the U.S. Department of Energy through the LANL/LDRD Program for this work.
Diamond Field-Emitter Array (DFEA) cathodes are arrays of micron-scale diamond pyramids with nanometer-scale tips. DFEAs can produce high emission currents with small emittance and energy spread. At LANL, we have an ongoing program to test DFEA cathodes for the purpose of using them to generate high-current, low-emittance electron beams for dielectric laser accelerators. We have recently upgraded our cathode test chamber to use a mesh anode in place of a solid luminescent anode. In addition to allowing for downstream beam transport, this arrangement may eliminate earlier problems with reduced cathode performance due to ion back-bombardment. We are measuring divergence of the electron beam past the mesh in an effort to characterize the inherent beam divergence off the diamond tip and divergence contribution from the mesh. We will compare these observations with theoretical and modeled values.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPML007

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPML010

Modeling of Diamond Field Emitter Arrays for Shaped Electron Beam Production

4668

K.E. Nichols, H.L. Andrews, D.Y. Shchegolkov, E.I. Simakov
LANL, Los Alamos, New Mexico, USA

We present simulations of shaped electron beam production from diamond field emitter array (DFEA) cathodes. DFEAs are arrays of diamond pyramids with bases of the order of 10 microns that produce high current densities. These arrays can be fabricated in arbitrary shapes such as a triangle or a double triangle, so that they produce an inherently shaped beam. These transversely shaped beams can be put through an emittance exchanger to produce a longitudinally shaped electron beam distribution for use with high-transformer ratio wakefield accelerators. Simulations are conducted with MICHELLE. We design cathodes and focusing systems that preserve the beam's shape while transporting it to the emittance exchanger.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPML010

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPML011

Possibilities for Fabricating Polymer Dielectric Laser Accelerator Structures with Additive Manufacturing

4671

E.I. Simakov, R.D. Gilbertson, M.J. Herman, G. Pilania, D.Y. Shchegolkov, E.M. Walker, E. Weis
LANL, Los Alamos, New Mexico, USA
R.J. England, K.P. Wootton
SLAC, Menlo Park, California, USA

Funding: Los Alamos National Laboratory LDRD Program
We present results of recent studies of new materials designed for the additive manufacturing of accelerating structures for dielectric laser accelerators (DLAs). Demonstration of a stand-alone practical DLA requires innovation in design and fabrication of efficient laser accelerator structures and couplers. Many complicated three-dimensional structures for laser acceleration (such as a long woodpile structure with couplers) are difficult to manufacture with conventional microfabrication technologies. LANL has a large effort focused on developing new materials and techniques for additive manufacturing. The materials for DLA structures must have high dielectric constant (larger than 4), low loss in the infrared regime, high laser damage threshold, and be able to withstand the electron beam damage. This presentation will discuss the development of novel infrared dielectric materials that are of interest for laser acceleration and are compatible with additive manufacturing, as well as recent advances in additive manufacturing of dielectric woodpile structures using a Nanoscribe direct laser-writing 3D printer.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPML011

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)