IPAC2018 - List of Authors (Sayeed, MNS.)

Paper	Title	Page
WEYGBF3	Nb3Sn Multicell Cavity Coating at JLab	1798
	U. Pudasaini, M.J. Kelley The College of William and Mary, Williamsburg, Virginia, USA G. Ciovati, G.V. Eremeev, M.J. Kelley, C.E. Reece JLab, Newport News, Virginia, USA M.J. Kelley Virginia Polytechnic Institute and State University, Blacksburg, USA I.P. Parajuli, MNS. Sayeed ODU, Norfolk, Virginia, USA
	Funding: This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics. Following encouraging results with Nb3Sn-coated R&D cavities, the existing coating system was upgraded to allow for Nb3Sn coating of CEBAF accelerator cavities. The upgrade was designed to allow Nb3Sn coating of original CEBAF 5-cell cavities with the vapor diffusion technique. Several CEBAF cavities were coated in the upgraded system to investigate vapor diffusion coatings on extended structures. Witness samples coated along with the cavities were characterized with material science techniques, while coated cavities were measured at 4 and 2 K. The progress, lessons learned, and the pathforward are discussed.
	Slides WEYGBF3 [2.381 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEYGBF3
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAL129	Magnetron Sputtering of Nb3Sn for SRF Cavities	3946
SUSPL076	use link to see paper's listing under its alternate paper code
	MNS. Sayeed, H. Elsayed-Ali ODU, Norfolk, Virginia, USA G.V. Eremeev, M.J. Kelley, C.E. Reece JLab, Newport News, Virginia, USA M.J. Kelley, U. Pudasaini The College of William and Mary, Williamsburg, Virginia, USA M.J. Kelley Virginia Polytechnic Institute and State University, Blacksburg, USA
	Nb3Sn is a potential candidate for surface material of SRF cavities since it can enable the cavity to operate at higher temperatures with high quality factor and at an increased accelerating gradient. Nb-Sn films were deposited using magnetron sputtering of individual Nb and Sn targets onto Nb and sapphire substrates. The as-deposited films were annealed at 1200 °C for 3 hours. The films were characterized for their structure by X-ray Diffraction (XRD), morphology by Field Emission Scanning Electron Microscopy (FESEM), and composition by Energy Dispersive X-ray Spectroscopy (EDS) and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The surface resistivity was measured down to cryogenic temperature to determine the superconducting transition temperature and its width. The composition of the multilayered films was controlled by varying the thickness of the Nb and Sn layers. The films showed crystalline Nb3Sn phases with Tc up to 17.6 K.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL129
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Nb3Sn Multicell Cavity Coating at JLab

1798

U. Pudasaini, M.J. Kelley
The College of William and Mary, Williamsburg, Virginia, USA
G. Ciovati, G.V. Eremeev, M.J. Kelley, C.E. Reece
JLab, Newport News, Virginia, USA
M.J. Kelley
Virginia Polytechnic Institute and State University, Blacksburg, USA
I.P. Parajuli, MNS. Sayeed
ODU, Norfolk, Virginia, USA

Funding: This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics.
Following encouraging results with Nb3Sn-coated R&D cavities, the existing coating system was upgraded to allow for Nb3Sn coating of CEBAF accelerator cavities. The upgrade was designed to allow Nb3Sn coating of original CEBAF 5-cell cavities with the vapor diffusion technique. Several CEBAF cavities were coated in the upgraded system to investigate vapor diffusion coatings on extended structures. Witness samples coated along with the cavities were characterized with material science techniques, while coated cavities were measured at 4 and 2 K. The progress, lessons learned, and the pathforward are discussed.

Slides WEYGBF3 [2.381 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEYGBF3

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAL129

Magnetron Sputtering of Nb3Sn for SRF Cavities

3946

SUSPL076

use link to see paper's listing under its alternate paper code

MNS. Sayeed, H. Elsayed-Ali
ODU, Norfolk, Virginia, USA
G.V. Eremeev, M.J. Kelley, C.E. Reece
JLab, Newport News, Virginia, USA
M.J. Kelley, U. Pudasaini
The College of William and Mary, Williamsburg, Virginia, USA
M.J. Kelley
Virginia Polytechnic Institute and State University, Blacksburg, USA

Nb3Sn is a potential candidate for surface material of SRF cavities since it can enable the cavity to operate at higher temperatures with high quality factor and at an increased accelerating gradient. Nb-Sn films were deposited using magnetron sputtering of individual Nb and Sn targets onto Nb and sapphire substrates. The as-deposited films were annealed at 1200 °C for 3 hours. The films were characterized for their structure by X-ray Diffraction (XRD), morphology by Field Emission Scanning Electron Microscopy (FESEM), and composition by Energy Dispersive X-ray Spectroscopy (EDS) and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The surface resistivity was measured down to cryogenic temperature to determine the superconducting transition temperature and its width. The composition of the multilayered films was controlled by varying the thickness of the Nb and Sn layers. The films showed crystalline Nb3Sn phases with Tc up to 17.6 K.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL129

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)